Different voltage values are sent to the multiplex tilt and telescopic ECU by operating the tilt and telescopic switch. The multiplex tilt and telescopic ECU then judges which motor and in which direction that motor should operate based on the voltage value.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2603 | Tilt and Telescopic Manual Switch Circuit Malfunction | When operating the tilt and telescopic switch, an abnormal voltage value is sent to the multiplex tilt and telescopic ECU. | ·
Tilt and telescopic switch ·
Harness or connector ·
Multiplex tilt and telescopic ECU |
| *1 | Tilt and Telescopic Switch |
| *a | Tilt Up |
| *b | Tilt Down |
| *c | Telescopic Extend (Long) |
| *d | Telescopic Contract (Short) |
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Check the tilt and telescopic switch.
Enter the following menus: Body Electrical / Tilt & Telescopic / Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Tilt Up Switch | Input state of tilt up switch | ON or OFF | ON: Tilt up switch activated
OFF: Tilt up switch not activated |
- |
| Tilt Down Switch | Input state of tilt down switch | ON or OFF | ON: Tilt down switch activated
OFF: Tilt down switch not activated |
- |
| Telesco Short Switch | Input state of telescopic contract switch | ON or OFF | ON: Telescopic contract switch activated
OFF: Telescopic contract switch not activated |
- |
| Telesco Long Switch | Input state of telescopic extend switch | ON or OFF | ON: Telescopic extend switch activated
OFF: Telescopic extend switch not activated |
- |
"ON" is displayed on the GTS screen when each switch is turned on.
"OFF" is displayed on the GTS screen when each switch is turned off.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Click hereSteering>STEERING COLUMN>POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM>DTC CHECK / CLEAR
Check for DTCs.
Click hereSteering>STEERING COLUMN>POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTCs are output. | A |
| DTCs are not output. | B |
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Disconnect the G211 multiplex tilt and telescopic ECU connector.
Disconnect the G223 tilt and telescopic switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G211-5 (VC) - G223-1 (VC) | Always | Below 1 Ω |
| G211-18 (MSW) - G223-3 (MSW) | Always | Below 1 Ω |
| G211-5 (VC) or G223-1 (VC) - Body ground | Always | 10 kΩ or higher |
| G211-18 (MSW) or G223-3 (MSW) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Multiplex Tilt and Telescopic ECU) |
Reconnect the G211 multiplex tilt and telescopic ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G211-5 (VC) - G211-18 (MSW) | Ignition switch ON | 4.9 to 5.1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Tilt and Telescopic Switch) |
Remove the tilt and telescopic switch.
Click hereSteering>STEERING COLUMN>TILT AND TELESCOPIC MANUAL SWITCH>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (VC) - 3 (MSW) | Tilt up | 342 to 378 Ω |
| Tilt down | 1890.5 to 2089.5 Ω | |
| Telescopic contract | 750.5 to 829.5 Ω | |
| Telescopic extend | 152 to 168 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG