Home › Steering › STEERING COLUMN › POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM › from 2017.08
RM27T0E _55 Steering _053718 STEERING COLUMN _0260955 POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM C

STEERING COLUMN  POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM  B2610  Tilt Position Sensor or Tilt Motor Circuit Malfunction  


DESCRIPTION

The tilt motor is operated by the power source voltage supplied from the multiplex tilt and telescopic ECU and tilts the steering column up and down. The tilt position sensor (Hall IC) in the tilt motor detects the tilt angle of the steering column and sends a signal to the multiplex tilt and telescopic ECU based on that angle.

C152160E06
1.031,0.198 2.24,0.542 1.208,0.344 10 Tilt Up Mechanical Lock Position 5.313,0.198 7.01,0.604 1.698,0.406 10 Tilt Down Mechanical Lock Position 2.969,1.292 4.115,1.49 1.146,0.198 10 Operation Range 1.302,2.083 2.615,2.354 1.313,0.271 10 Tilt Up Limit Position 4.333,2.083 5.896,2.333 1.563,0.25 10 Tilt Down Limit Position

HINT:

Limit positions can be confirmed on the GTS.


DTC No. Detection Item DTC Detection Condition Trouble Area
B2610 Tilt Position Sensor or Tilt Motor Circuit Malfunction Tilt operation stops within the operation range while operating.
·

Tilt position sensor or tilt motor (steering column assembly (tilt steering gear assembly with motor))

·

Harness or connector

·

Multiplex tilt and telescopic ECU



WIRING DIAGRAM

C244371E50
0.979,1.427 1.792,1.615 0.813,0.188 10 false Tilt Motor 2.146,0.781 2.99,0.99 0.844,0.208 10 false from Battery 3.49,0.958 4.073,1.167 0.583,0.208 10 false TI & TE 4.677,4.802 5.24,5 0.563,0.198 10 false G211 4.688,0.802 4.979,0.948 0.292,0.146 10 false +B 6.01,0.927 6.302,1.073 0.292,0.146 10 false +B 6.01,1.729 6.302,1.875 0.292,0.146 10 false +B 6.073,2.938 6.531,3.135 0.458,0.198 10 false 12 V 5.99,3.656 6.604,3.885 0.615,0.229 10 false to CPU 4.688,1.125 5.042,1.271 0.354,0.146 10 false TIM+ 4.688,2.667 5.073,2.875 0.385,0.208 10 false VCI 4.688,3.063 4.958,3.219 0.271,0.156 10 false TIS 4.688,3.865 5.25,4.063 0.563,0.198 10 false GND2 4.688,4.979 6.792,5.146 2.104,0.167 10 false Multiplex Tilt and Telescopic ECU 4.688,3.458 4.99,3.635 0.302,0.177 10 false E1 4.688,1.917 5.042,2.063 0.354,0.146 10 false TIM- 4.479,0.708 4.646,0.917 0.167,0.208 10 false 2 4.417,1.927 4.656,2.073 0.24,0.146 10 false 20 4.417,2.667 4.698,2.875 0.281,0.208 10 false 13 4.417,3.063 4.656,3.26 0.24,0.198 10 false 16 4.479,1.125 4.708,1.323 0.229,0.198 10 false 7 4.479,3.479 4.667,3.625 0.188,0.146 10 false 4 4.479,3.865 4.708,4.052 0.229,0.188 10 false 8 4.688,4.396 5.25,4.594 0.563,0.198 10 false GND 4.479,4.302 4.667,4.448 0.188,0.146 10 false 1 0.5,3.75 1.906,3.948 1.406,0.198 10 false Tilt Position Sensor 0.406,4.771 1.052,5.01 0.646,0.24 10 false G122 0.406,4.948 3.563,5.344 3.156,0.396 10 false Tilt Motor (Steering Column Assembly (Tilt Steering Gear Assembly with Motor)) 1.719,1.115 2.094,1.302 0.375,0.188 10 false TIM+ 2.125,1.917 2.354,2.094 0.229,0.177 10 false 2 1.729,1.906 2.146,2.115 0.417,0.208 10 false TIM- 2.125,1.125 2.375,1.344 0.25,0.219 10 false 1 1.771,2.656 2.094,2.865 0.323,0.208 10 false VCI 2.135,2.656 2.323,2.865 0.188,0.208 10 false 4 1.792,3.052 2.083,3.24 0.292,0.188 10 false TIS 2.135,3.052 2.365,3.26 0.229,0.208 10 false 5 1.833,3.448 2.125,3.667 0.292,0.219 10 false E1 2.135,3.458 2.365,3.677 0.229,0.219 10 false 6

CAUTION / NOTICE / HINT

HINT:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (TILT OPERATION)
a.
C106468C01
2.219,0.271 2.5,0.469 0.281,0.198 10 *a 2.333,1.104 2.656,1.313 0.323,0.208 10 *b
*a Up
*b Down


Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Check that the steering wheel tilts up and down.


f.

Enter the following menus: Body Electrical / Tilt & Telescopic / Active Test.

Body Electrical > Tilt&Telescopic > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Tilt Operation Tilt operation UP/DOWN -

OK:

The steering wheel tilts up and down.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT POSITION SENSOR)

NG

6.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BATTERY)
2.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT POSITION SENSOR)
a.

Disconnect the G211 multiplex tilt and telescopic ECU connector.


b.

Disconnect the G122 tilt motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G211-13 (VCI) - G122-4 (VCI) Always Below 1 Ω
G211-16 (TIS) - G122-5 (TIS) Always Below 1 Ω
G211-4 (E1) -G122-6 (E1) Always Below 1 Ω
G211-13 (VCI) or G122-4 (VCI) - Body ground Always 10 kΩ or higher
G211-16 (TIS) or G122-5 (TIS) - Body ground Always 10 kΩ or higher
G211-4 (E1) or G122-6 (E1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)
a.
C387819C01
1.469,0.281 1.917,0.521 0.448,0.24 0.802,0.979 0.719,0.677 0.719,0.677 0.552,0.677 true 0.771,1.229 0.729,1.615 0.729,1.615 0.563,1.615 true 1.531,0.323 2.146,0.521 0.615,0.198 10 false G211 0.167,1.531 0.781,1.729 0.615,0.198 10 false GND2 0.219,0.604 0.833,0.802 0.615,0.198 10 false GND
*a Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)


Disconnect the G211 multiplex tilt and telescopic ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G211-1 (GND) - Body ground Always Below 1 Ω
G211-8 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VCI, TIS TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VCI, TIS TERMINAL VOLTAGE)
a.
C267905C83
1.417,0.24 1.979,0.51 0.563,0.271 1.302,0.896 1.167,0.667 true 1.24,1.531 1.448,1.156 true 2.115,1.552 1.875,1.146 true 1.531,0.292 1.917,0.5 0.385,0.208 10 false G211 1.063,0.49 1.344,0.656 0.281,0.167 10 false E1 1.135,1.552 1.458,1.781 0.323,0.229 10 false TIS 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a 2.01,1.563 2.469,1.76 0.458,0.198 10 false VCI
*a Component with harness connected
(Multiplex Tilt and Telescopic ECU)


Disconnect the G122 tilt motor connector.


b.

Reconnect the G211 multiplex tilt and telescopic ECU connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G211-13 (VCI) - G211-4 (E1) Ignition switch ON 8 to 14 V
G211-16 (TIS) - G211-4 (E1) Ignition switch ON 8 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK TILT POSITION SENSOR

NG

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

5.CHECK TILT POSITION SENSOR
a.
C287133C43
1.417,0.313 1.958,0.573 0.542,0.26 0.938,1.823 1.354,1.406 true 1.667,1.406 2.635,1.823 true 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 1.531,0.354 2.146,0.625 0.615,0.271 10 false G122 0.719,1.76 1.031,1.958 0.313,0.198 10 false E1 2.698,1.76 3.156,1.958 0.458,0.198 10 false TIS
*a Component with harness connected
(Tilt Motor)


Reconnect the G211 multiplex tilt and telescopic ECU connector.


b.

Reconnect the G122 tilt motor connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G122-5 (TIS) - G122-6 (E1) Steering wheel tilting up or tilting down Pulse generation
High: 8 to 14 V
Low: Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

NG

REPLACE STEERING COLUMN ASSEMBLY (TILT STEERING GEAR ASSEMBLY WITH MOTOR)

6.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BATTERY)
a.
C387819C02
1.469,0.281 1.917,0.521 0.448,0.24 0.979,0.979 0.865,0.521 0.865,0.521 0.698,0.521 true 1.531,0.323 2.146,0.521 0.615,0.198 10 false G211 0.479,0.448 1.094,0.646 0.615,0.198 10 false +B
*a Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)


Disconnect the G211 multiplex tilt and telescopic ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G211-2 (+B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)
a.
C387819C01
1.469,0.281 1.917,0.521 0.448,0.24 0.802,0.979 0.719,0.677 0.719,0.677 0.552,0.677 true 0.771,1.229 0.729,1.615 0.729,1.615 0.563,1.615 true 1.531,0.323 2.146,0.521 0.615,0.198 10 false G211 0.167,1.531 0.781,1.729 0.615,0.198 10 false GND2 0.219,0.604 0.833,0.802 0.615,0.198 10 false GND
*a Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)


Disconnect the G211 multiplex tilt and telescopic ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G211-1 (GND) - Body ground Always Below 1 Ω
G211-8 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT MOTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT MOTOR)
a.

Disconnect the G211 multiplex tilt and telescopic ECU connector.


b.

Disconnect the G122 tilt motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G211-7 (TIM+) - G122-1 (TIM+) Always Below 1 Ω
G211-20 (TIM-) - G122-2 (TIM-) Always Below 1 Ω
G211-7 (TIM+) or G122-1 (TIM+) - Body ground Always 10 kΩ or higher
G211-20 (TIM-) or G122-2 (TIM-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK TILT MOTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK TILT MOTOR
a.
C197978C63
2.042,1.115 2.354,0.667 true 1.354,1.115 1.042,0.667 true 0.302,0.229 0.51,0.417 0.208,0.188 10 false *a 2.406,0.573 2.927,0.781 0.521,0.208 10 false TIM+ 0.729,0.573 1.188,0.781 0.458,0.208 10 false TIM-
*a Component without harness connected
(Tilt Motor)


Apply 12 V battery voltage to the tilt motor connector. Then check the steering wheel tilt operation.

OK:
Measurement Condition Specified Condition
·

12 V battery positive (+) lead → Terminal 2 (TIM-)

·

12 V battery negative (-) lead → Terminal 1 (TIM+)


The steering wheel tilts down.
·

12 V battery positive (+) lead → Terminal 1 (TIM+)

·

12 V battery negative (-) lead → Terminal 2 (TIM-)


The steering wheel tilts up.



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

NG

REPLACE STEERING COLUMN ASSEMBLY (TILT STEERING GEAR ASSEMBLY WITH MOTOR)