Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column) › 2017.08–2020.08
RM27T0E _55 Steering _053718 STEERING COLUMN _0260958 STEERING COLUMN ASSEMBLY(for Power Tilt and Power Telescopic Steering Column) A

STEERING COLUMN  STEERING COLUMN ASSEMBLY(for Power Tilt and Power Telescopic Steering Column)  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing the steering wheel (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1.PLACE FRONT WHEELS FACING STRAIGHT AHEAD

Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

a.

Disable the auto tilt away function by changing the customize parameter (See pageSteering>STEERING COLUMN>POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM>CUSTOMIZE PARAMETERS ).

NOTICE:

Record the current customize parameter setting (whether the auto tilt away function is enabled or disabled) in order to restore the current setting after finishing the operation.


HINT:

Performing the above operation causes the auto tilt away function to be disabled when the engine switch is turned off.



b.

Turn the engine switch on (IG). Operate the tilt and telescopic switch to fully extend and lower the steering column assembly.


c.

Turn the engine switch off and disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




Hide 3.REMOVE FRONT WHEEL LH

Hide 45100 4.REMOVE STEERING WHEEL ASSEMBLY

Hide 45287 5.REMOVE STEERING COLUMN LOWER COVER

a.
C384107

Remove the 3 screws.


b.

Detach the 2 claws and remove the steering column lower cover.

NOTICE:

Do not damage the tilt and telescopic switch.



Hide 45286B 6.REMOVE STEERING COLUMN UPPER COVER

a.
C384108

Detach the 4 clips.


b.

Detach the claw and remove the steering column upper cover.


Hide 89235A 7.REMOVE TILT AND TELESCOPIC SWITCH

Hide 8.REMOVE COMBINATION SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

a.

Disconnect the connectors from the combination switch with spiral cable.


b.
C384109

Use pliers to hold the clamp and raise the claw with a screwdriver. Then remove the combination switch switch assembly with spiral cable sub-assembly from the steering column assembly.


Hide 55045 9.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (w/o Knee Airbag)

Hide 73900 10.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Knee Airbag)

Hide 45250 11.REMOVE STEERING COLUMN ASSEMBLY

a.

Disconnect the connectors.


b.

Detach the claws and remove the wire harness protector and wire harness.


c.
C215861E07
1.656,1.073 2.688,1.625 2.688,1.625 3.042,1.625 true 1.688,0.906 2.917,1.625 true 3.063,1.531 3.396,1.792 0.333,0.26 10 true *a

Put matchmarks on the steering actuator and steering column.

Text in Illustration
*a Matchmark


d.

Remove the bolt.


e.
C384110

Remove the 4 nuts, steering column and steering shaft stopper.


Hide 53736B 12.REMOVE FRONT NO. 1 FENDER APRON TO FRAME SEAL RH