Home › Steering › STEERING COLUMN › POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM › from 2017.08
RM27T0E _55 Steering _053718 STEERING COLUMN _0260955 POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM C

STEERING COLUMN  POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM  B2611  Telescopic Position Sensor or Telescopic Motor Circuit Malfunction  


DESCRIPTION

The telescopic motor is operated by the power source voltage supplied from the multiplex tilt and telescopic ECU and slides the steering column forward and backward. The telescopic position sensor (Hall IC) in the telescopic motor detects the sliding position of the steering column in the forward and backward directions and sends a signal to the multiplex tilt and telescopic ECU based on that sliding amount.

C152160E07
0.521,0.198 2.469,0.635 1.948,0.438 10 Telescopic Steering Contracted Mechanical Lock Position 4.698,0.198 6.635,0.615 1.938,0.417 10 Telescopic Steering Extended Mechanical Lock Position 1.104,2 3.042,2.354 1.938,0.354 10 Telescopic Steering Contracted Limit Position 4.333,2 6.219,2.375 1.885,0.375 10 Telescopic Steering Extended Limit Position 2.99,1.313 4.188,1.51 1.198,0.198 10 Operation Range

HINT:

Limit positions can be confirmed on the GTS.


DTC No. Detection Item DTC Detection Condition Trouble Area
B2611 Telescopic Position Sensor or Telescopic Motor Circuit Malfunction Telescopic operation stops within the operation range while operating.
·

Telescopic position sensor or telescopic motor (steering column assembly (tilt steering gear assembly with motor))

·

Harness or connector

·

Multiplex tilt and telescopic ECU



WIRING DIAGRAM

C244373E37
2.156,0.885 2.927,1.073 0.771,0.188 10 false from Battery 3.5,1.063 4.094,1.271 0.594,0.208 10 false TI & TE 4.698,0.885 4.99,1.031 0.292,0.146 10 false +B 4.49,0.802 4.594,0.948 0.104,0.146 10 false 2 1.667,1.198 2.083,1.344 0.417,0.146 10 false TEM+ 2.135,1.99 2.25,2.135 0.115,0.146 10 false 1 1.688,1.99 2.115,2.135 0.427,0.146 10 false TEM- 2.146,1.198 2.26,1.344 0.115,0.146 10 false 2 1.729,2.75 2.208,2.896 0.479,0.146 10 false VCE 2.146,2.74 2.385,2.969 0.24,0.229 10 false 5 1.76,3.156 2.094,3.302 0.333,0.146 10 false TES 2.146,3.146 2.385,3.354 0.24,0.208 10 false 4 1.854,3.552 2.052,3.698 0.198,0.146 10 false E2 2.146,3.531 2.375,3.76 0.229,0.229 10 false 3 0.771,1.469 2,1.677 1.229,0.208 10 false Telescopic Motor 4.688,1.198 5.104,1.396 0.417,0.198 10 false TEM+ 4.688,2 5.063,2.198 0.375,0.198 10 false TEM- 4.677,2.76 5,2.958 0.323,0.198 10 false VCE 4.688,3.146 5.021,3.344 0.333,0.198 10 false TES 4.688,3.542 4.938,3.74 0.25,0.198 10 false E2 0.49,3.802 1.781,4.208 1.292,0.406 10 false Telescopic Position Sensor 4.417,2 4.604,2.198 0.188,0.198 10 false 19 4.417,2.76 4.604,2.969 0.188,0.208 10 false 14 4.427,3.146 4.74,3.354 0.313,0.208 10 false 15 4.688,4.75 5.198,4.958 0.51,0.208 10 false G211 4.49,1.208 4.729,1.406 0.24,0.198 10 false 6 4.479,3.844 4.719,4.042 0.24,0.198 10 false 8 4.417,3.542 4.729,3.74 0.313,0.198 10 false 17 4.677,3.854 5.24,4.052 0.563,0.198 10 false GND2 4.49,4.24 4.729,4.438 0.24,0.198 10 false 1 4.677,4.323 5.24,4.521 0.563,0.198 10 false GND 6.021,1.021 6.333,1.219 0.313,0.198 10 false +B 6.021,1.813 6.333,2.01 0.313,0.198 10 false +B 6.083,3.042 6.49,3.24 0.406,0.198 10 false 12 V 6.031,3.75 6.604,3.948 0.573,0.198 10 false to CPU 4.688,4.927 6.833,5.125 2.146,0.198 10 false Multiplex Tilt and Telescopic ECU 0.438,4.906 3.26,5.292 2.823,0.385 10 false Telescopic Motor (Steering Column Assembly (Tilt Steering Gear Assembly with Motor)) 0.438,4.74 1.125,5.021 0.688,0.281 10 false G221

CAUTION / NOTICE / HINT

HINT:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (TILT OPERATION)
a.
C106469C01
1.313,0.229 1.563,0.427 0.25,0.198 10 *a 2.458,1.792 2.688,1.99 0.229,0.198 10 *b
*a Extend
*b Contract


Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Check that the steering column contracts and extends.


f.

Enter the following menus: Body Electrical / Tilt & Telescopic / Active Test.

Body Electrical > Tilt&Telescopic > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Telesco Operation Telesco Operation LONG/SHORT -

OK:

The steering column contracts and extends.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TELESCOPIC POSITION SENSOR)

NG

6.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BATTERY)
2.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TELESCOPIC POSITION SENSOR)
a.

Disconnect the G211 multiplex tilt and telescopic ECU connector.


b.

Disconnect the G221 telescopic motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G211-14 (VCE) - G221-5 (VCE) Always Below 1 Ω
G211-15 (TES) - G221-4 (TES) Always Below 1 Ω
G211-17 (E2) - G221-3 (E2) Always Below 1 Ω
G211-14 (VCE) or G221-5 (VCE) - Body ground Always 10 kΩ or higher
G211-15 (TES) or G221-4 (TES) - Body ground Always 10 kΩ or higher
G211-17 (E2) or G221-3 (E2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)
a.
C387819C01
1.469,0.281 1.917,0.521 0.448,0.24 0.802,0.979 0.719,0.677 0.719,0.677 0.552,0.677 true 0.771,1.229 0.729,1.615 0.729,1.615 0.563,1.615 true 1.531,0.323 2.146,0.521 0.615,0.198 10 false G211 0.167,1.531 0.781,1.729 0.615,0.198 10 false GND2 0.219,0.604 0.833,0.802 0.615,0.198 10 false GND
*a Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)


Disconnect the G211 multiplex tilt and telescopic ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G211-1 (GND) - Body ground Always Below 1 Ω
G211-8 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VCE, TES TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VCE, TES TERMINAL VOLTAGE)
a.
C267905C84
1.417,0.24 1.979,0.51 0.563,0.271 1.948,1.552 1.583,1.135 true 1.24,1.531 1.302,1.146 true 2.427,1.563 1.719,1.146 true 1.531,0.302 2.083,0.51 0.552,0.208 10 false G211 1.156,1.552 1.438,1.719 0.281,0.167 10 false E2 1.844,1.563 2.167,1.792 0.323,0.229 10 false TES 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a 2.302,1.563 2.76,1.76 0.458,0.198 10 false VCE
*a Component with harness connected
(Multiplex Tilt and Telescopic ECU)


Disconnect the G221 telescopic motor connector.


b.

Reconnect the G211 multiplex tilt and telescopic ECU connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G211-14 (VCE) - G211-17 (E2) Ignition switch ON 8 to 14 V
G211-15 (TES) - G211-17 (E2) Ignition switch ON 8 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK TELESCOPIC POSITION SENSOR

NG

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

5.CHECK TELESCOPIC POSITION SENSOR
a.
C287133C44
1.417,0.313 1.958,0.573 0.542,0.26 1.802,1.417 2.271,1.823 2.271,1.823 2.5,1.823 true 2.052,1.354 2.417,1.021 2.417,1.021 2.646,1.021 true 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 1.521,0.365 1.875,0.583 0.354,0.219 10 false G221 2.542,1.74 3.083,1.948 0.542,0.208 10 false TES 2.698,0.948 3.156,1.146 0.458,0.198 10 false E2
*a Component with harness connected
(Telescopic Motor)


Reconnect the G211 multiplex tilt and telescopic ECU connector.


b.

Reconnect the G221 telescopic motor connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G221-4 (TES) - G221-3 (E2) Steering column contracting or extending Pulse generation
High: 8 to 14 V
Low: Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

NG

REPLACE STEERING COLUMN ASSEMBLY (TILT STEERING GEAR ASSEMBLY WITH MOTOR)

6.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BATTERY)
a.

Disconnect the G211 multiplex tilt and telescopic ECU connector.


b.
C387819C02
1.469,0.281 1.917,0.521 0.448,0.24 0.979,0.979 0.865,0.521 0.865,0.521 0.698,0.521 true 1.531,0.323 2.146,0.521 0.615,0.198 10 false G211 0.479,0.448 1.094,0.646 0.615,0.198 10 false +B
*a Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G211-2 (+B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)
a.
C387819C01
1.469,0.281 1.917,0.521 0.448,0.24 0.802,0.979 0.719,0.677 0.719,0.677 0.552,0.677 true 0.771,1.229 0.729,1.615 0.729,1.615 0.563,1.615 true 1.531,0.323 2.146,0.521 0.615,0.198 10 false G211 0.167,1.531 0.781,1.729 0.615,0.198 10 false GND2 0.219,0.604 0.833,0.802 0.615,0.198 10 false GND
*a Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)


Disconnect the G211 multiplex tilt and telescopic ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G211-1 (GND) - Body ground Always Below 1 Ω
G211-8 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TELESCOPIC MOTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TELESCOPIC MOTOR)
a.

Disconnect the G211 multiplex tilt and telescopic ECU connector.


b.

Disconnect the G221 telescopic motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G211-6 (TEM+) - G221-2 (TEM+) Always Below 1 Ω
G211-19 (TEM-) - G221-1 (TEM-) Always Below 1 Ω
G211-6 (TEM+) or G221-2 (TEM+) - Body ground Always 10 kΩ or higher
G211-19 (TEM-) or G221-1 (TEM-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK TELESCOPIC MOTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK TELESCOPIC MOTOR
a.
C197978C07
2.031,1.115 2.344,0.667 false 1.344,1.135 1.031,0.688 false 0.302,0.229 0.51,0.417 0.208,0.188 10 *a 2.385,0.563 2.844,0.75 0.458,0.188 10 TEM- 0.646,0.563 1.135,0.75 0.49,0.188 10 TEM+
*a Component without harness connected
(Telescopic Motor)


Apply 12 V battery voltage to the telescopic motor connector. Then check the steering column telescopic operation.

OK:
Measurement Condition Specified Condition
·

12 V battery positive (+) lead → Terminal 2 (TEM+)

·

12 V battery negative (-) lead → Terminal 1 (TEM-)


The steering column contracts.
·

12 V battery positive (+) lead → Terminal 1 (TEM-)

·

12 V battery negative (-) lead → Terminal 2 (TEM+)


The steering column extends.



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

NG

REPLACE STEERING COLUMN ASSEMBLY (TILT STEERING GEAR ASSEMBLY WITH MOTOR)