Home › Steering › STEERING COLUMN › POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM › from 2017.08
RM27T0E _55 Steering _053718 STEERING COLUMN _0260955 POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM J

STEERING COLUMN  POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM  Tilt and Telescopic Manual Switch Circuit  


DESCRIPTION

Different voltage values are sent to the multiplex tilt and telescopic ECU by operating the tilt and telescopic switch. The multiplex tilt and telescopic ECU then judges which motor and in which direction that motor should operate based on the voltage value.

WIRING DIAGRAM

C240527E72
4.917,3.875 7.073,4.188 2.156,0.313 10 false Multiplex Tilt and Telescopic ECU 1.458,3.75 3.583,3.906 2.125,0.156 10 false Tilt and Telescopic Switch 3.75,2.646 4.115,2.802 0.365,0.156 10 false MSW 3.906,1 4.125,1.156 0.219,0.156 10 false VC 5.125,2.75 5.49,2.906 0.365,0.156 10 false MSW 5.135,1.094 5.354,1.25 0.219,0.156 10 false VC 0.708,1.979 1.333,2.448 0.625,0.469 10 false Tilt Down 1.573,1.896 2.25,2.458 0.677,0.563 10 false Telescopic Contract 2.448,1.979 2.979,2.281 0.531,0.302 10 false Tilt Up 3.333,1.885 4.031,2.469 0.698,0.583 10 false Telescopic Extend 4.927,1 5.104,1.167 0.177,0.167 10 false 5 4.865,2.646 5.104,2.813 0.24,0.167 10 false 18 4.917,3.688 5.469,3.885 0.552,0.198 10 false G211 1.458,3.563 2.031,3.792 0.573,0.229 10 false G223 4.177,2.646 4.354,2.813 0.177,0.167 10 false 3 4.177,1 4.354,1.167 0.177,0.167 10 false 1

PROCEDURE

1.READ VALUE USING GTS (TILT UP/DOWN SWITCH, TELESCOPIC SHORT/LONG SWITCH)
a.
C113518C03
1.26,0.198 1.521,0.396 0.26,0.198 10 false *a 1.771,1.781 2.458,1.979 0.688,0.198 10 false *b 2.24,0.542 2.521,0.75 0.281,0.208 10 false *c 0.844,1.354 1.083,1.573 0.24,0.219 10 false *d 0.094,0.073 0.406,0.271 0.313,0.198 10 false *1
*1 Tilt and Telescopic Switch
*a Tilt Up
*b Tilt Down
*c Telescopic Extend (Long)
*d Telescopic Contract (Short)


Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Check the tilt and telescopic switch.


f.

Enter the following menus: Body Electrical / Tilt & Telescopic / Data List.

Body Electrical > Tilt&Telescopic > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Tilt Up Switch Input state of tilt up switch ON or OFF ON: Tilt up switch activated
OFF: Tilt up switch not activated
-
Tilt Down Switch Input state of tilt down switch ON or OFF ON: Tilt down switch activated
OFF: Tilt down switch not activated
-
Telesco Short Switch Input state of telescopic contract switch ON or OFF ON: Telescopic contract switch activated
OFF: Telescopic contract switch not activated
-
Telesco Long Switch Input state of telescopic extend switch ON or OFF ON: Telescopic extend switch activated
OFF: Telescopic extend switch not activated
-

OK:

"ON" is displayed on the GTS screen when each switch is turned on.

"OFF" is displayed on the GTS screen when each switch is turned off.



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

NG

2.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT AND TELESCOPIC SWITCH)
2.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT AND TELESCOPIC SWITCH)
a.

Disconnect the G211 multiplex tilt and telescopic ECU connector.


b.

Disconnect the G223 tilt and telescopic switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G211-5 (VC) - G223-1 (VC) Always Below 1 Ω
G211-18 (MSW) - G223-3 (MSW) Always Below 1 Ω
G211-5 (VC) or G223-1 (VC) - Body ground Always 10 kΩ or higher
G211-18 (MSW) or G223-3 (MSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VC TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VC TERMINAL VOLTAGE)
a.
C267905C82
1.458,0.24 1.917,0.5 0.458,0.26 1.167,0.906 1.167,0.677 true 1.167,1.521 1.167,1.146 true 1.521,0.292 2.031,0.5 0.51,0.208 10 false G211 1.073,0.49 1.354,0.656 0.281,0.167 10 false VC 1.01,1.552 1.458,1.771 0.448,0.219 10 false MSW 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a
*a Component with harness connected
(Multiplex Tilt and Telescopic ECU)


Reconnect the G211 multiplex tilt and telescopic ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G211-5 (VC) - G211-18 (MSW) Ignition switch ON 4.9 to 5.1 V



Result:
Proceed to
OK
NG



OK

4.CHECK TILT AND TELESCOPIC SWITCH

NG

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

4.CHECK TILT AND TELESCOPIC SWITCH
a.
C240949C05
1.479,1.458 1.156,1.844 false 1.938,1.458 2.281,1.854 false 0.125,0.031 0.385,0.188 0.26,0.156 10 *a 0.938,1.865 1.333,2.052 0.396,0.188 10 MSW 2.219,1.865 2.615,2.052 0.396,0.188 10 VC
*a Component without harness connected
(Tilt and Telescopic Switch)


Remove the tilt and telescopic switch.

Click hereSteering>STEERING COLUMN>TILT AND TELESCOPIC MANUAL SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (VC) - 3 (MSW) Tilt up 342 to 378 Ω
Tilt down 1890.5 to 2089.5 Ω
Telescopic contract 750.5 to 829.5 Ω
Telescopic extend 152 to 168 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE TILT AND TELESCOPIC SWITCH