Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › from 2017.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0261011 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB0  Short to +B in Outer Mirror Indicator(Master)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor LH detects a +B short in the outer rear view mirror indicator LH.

DTC No. DTC Detection Condition Trouble Area
C1AB0
Both of the following conditions are met:
·

The blind spot monitor system is on

·

The blind spot monitor sensor is not sending voltage to the indicator but the indicator receives voltage above a specified level for a specified period of time


·

Outer mirror LH (outer rear view mirror indicator LH)

·

Outer rear view mirror assembly LH

·

Harness or connector

·

Blind spot monitor sensor LH

·

Outer mirror control ECU assembly LH



WIRING DIAGRAM

E329056E33
1.563,1.229 1.719,1.427 0.156,0.198 10 false 2 1.583,1.729 1.854,1.938 0.271,0.208 10 false 1 1.375,1.365 1.531,1.563 0.156,0.198 10 false + 1.375,1.823 1.531,2.021 0.156,0.198 10 false - 0.323,2.198 0.979,2.427 0.656,0.229 10 false IND2 0.323,2.344 2.052,2.74 1.729,0.396 10 false Outer Mirror LH (Outer Rear View Mirror Indicator LH) 0.208,3.406 2.688,3.698 2.479,0.292 10 false Outer Rear View Mirror Assembly LH 2.875,1.354 3.344,1.552 0.469,0.198 10 false z18 2.875,1.833 3.344,2.031 0.469,0.198 10 false z18 2.958,1.177 3.208,1.365 0.25,0.188 10 false 8 2.917,1.646 3.385,1.844 0.469,0.198 10 false 12 3.281,1.354 3.75,1.552 0.469,0.198 10 false BDIL 3.281,1.854 3.75,2.052 0.469,0.198 10 false HTR- 3.198,3.406 4.438,3.823 1.24,0.417 10 false Outer Mirror Control ECU Assembly LH 4.021,1.375 4.49,1.573 0.469,0.198 10 false BDSL 4.104,1.833 4.573,2.031 0.469,0.198 10 false GND 4.531,1.354 5,1.552 0.469,0.198 10 false K12 4.542,1.823 5.01,2.021 0.469,0.198 10 false K12 4.583,1.167 5.052,1.365 0.469,0.198 10 false 13 4.604,1.646 5.073,1.844 0.469,0.198 10 false 7 5.969,1.375 6.438,1.573 0.469,0.198 10 false OMIL 5.781,1.25 6.25,1.448 0.469,0.198 10 false 4 5.885,3.396 6.354,3.594 0.469,0.198 10 false R42 5.885,3.583 7.094,4.198 1.208,0.615 10 false Blind Spot Monitor Sensor LH

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor system is on.


PROCEDURE

1.CHECK DTC

b.

Recheck for DTCs and check if the same DTC is output again.

OK:

DTC C1AB0 is not output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - OUTER MIRROR LH)
2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - OUTER MIRROR LH)
a.
E383327C01
1.438,0.25 1.938,0.5 0.5,0.25 1.854,1.146 2.24,0.604 2.24,0.604 2.49,0.604 true 1.573,0.292 2.031,0.49 0.458,0.198 10 false R42 0.042,0.031 0.5,0.229 0.458,0.198 10 false *a 2.552,0.521 3.01,0.719 0.458,0.198 10 false OMIL
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)


Disconnect the blind spot monitor sensor LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R42-4 (OMIL) - Body ground Engine switch on (IG) Below 1 V



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - OUTER REAR VIEW MIRROR ASSEMBLY LH)
3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - OUTER REAR VIEW MIRROR ASSEMBLY LH)
a.
E383327C01
1.438,0.25 1.938,0.5 0.5,0.25 1.854,1.146 2.24,0.604 2.24,0.604 2.49,0.604 true 1.573,0.292 2.031,0.49 0.458,0.198 10 false R42 0.042,0.031 0.5,0.229 0.458,0.198 10 false *a 2.552,0.521 3.01,0.719 0.458,0.198 10 false OMIL
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)


Disconnect the blind spot monitor sensor LH connector.


b.

Disconnect the IND2 outer mirror LH connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R42-4 (OMIL) - Body ground Engine switch on (IG) Below 1 V



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - OUTER MIRROR CONTROL ECU ASSEMBLY LH)
4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - OUTER MIRROR CONTROL ECU ASSEMBLY LH)
a.
E383327C01
1.438,0.25 1.938,0.5 0.5,0.25 1.854,1.146 2.24,0.604 2.24,0.604 2.49,0.604 true 1.573,0.292 2.031,0.49 0.458,0.198 10 false R42 0.042,0.031 0.5,0.229 0.458,0.198 10 false *a 2.552,0.521 3.01,0.719 0.458,0.198 10 false OMIL
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)


Disconnect the blind spot monitor sensor LH connector.


b.

Disconnect the z18 outer mirror control ECU assembly LH connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R42-4 (OMIL) - Body ground Engine switch on (IG) Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

NG

5.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - OUTER MIRROR CONTROL ECU ASSEMBLY LH)
5.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - OUTER MIRROR CONTROL ECU ASSEMBLY LH)
a.
E383327C01
1.438,0.25 1.938,0.5 0.5,0.25 1.854,1.146 2.24,0.604 2.24,0.604 2.49,0.604 true 1.573,0.292 2.031,0.49 0.458,0.198 10 false R42 0.042,0.031 0.5,0.229 0.458,0.198 10 false *a 2.552,0.521 3.01,0.719 0.458,0.198 10 false OMIL
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)


Disconnect the blind spot monitor sensor LH connector.


b.

Disconnect the K12 outer mirror control ECU assembly LH connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R42-4 (OMIL) - Body ground Engine switch on (IG) Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR