Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › from 2017.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0261011 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB3  Short to GND in Outer Mirror Indicator(Slave)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor RH detects a ground short in the outer rear view mirror indicator RH.

DTC No. DTC Detection Condition Trouble Area
C1AB3
Both of the following conditions are met:
·

The blind spot monitor system is on

·

The current that is sent from the blind spot monitor sensor to the indicator is above a specified level for a specified period of time


·

Outer mirror RH (outer rear view mirror indicator RH)

·

Outer rear view mirror assembly RH

·

Harness or connector

·

Blind spot monitor sensor RH

·

Outer mirror control ECU assembly RH



WIRING DIAGRAM

E329056E34
1.563,1.229 1.719,1.427 0.156,0.198 10 false 2 1.583,1.729 1.854,1.938 0.271,0.208 10 false 1 1.375,1.365 1.531,1.563 0.156,0.198 10 false + 1.375,1.823 1.531,2.021 0.156,0.198 10 false - 0.323,2.198 0.979,2.427 0.656,0.229 10 false IND1 0.323,2.344 2.052,2.74 1.729,0.396 10 false Outer Mirror RH (Outer Rear View Mirror Indicator RH) 0.208,3.406 2.688,3.698 2.479,0.292 10 false Outer Rear View Mirror Assembly RH 2.875,1.354 3.344,1.552 0.469,0.198 10 false z19 2.875,1.833 3.344,2.031 0.469,0.198 10 false z19 2.958,1.177 3.208,1.365 0.25,0.188 10 false 8 2.917,1.646 3.385,1.844 0.469,0.198 10 false 12 3.281,1.354 3.75,1.552 0.469,0.198 10 false BDIR 3.281,1.854 3.75,2.052 0.469,0.198 10 false HTR- 3.198,3.406 4.438,3.823 1.24,0.417 10 false Outer Mirror Control ECU Assembly RH 4.021,1.375 4.49,1.573 0.469,0.198 10 false BDSR 4.104,1.833 4.573,2.031 0.469,0.198 10 false GND 4.531,1.354 5,1.552 0.469,0.198 10 false J12 4.542,1.823 5.01,2.021 0.469,0.198 10 false J12 4.583,1.167 5.052,1.365 0.469,0.198 10 false 13 4.604,1.646 5.073,1.844 0.469,0.198 10 false 7 5.969,1.375 6.438,1.573 0.469,0.198 10 false OMIR 5.781,1.25 6.25,1.448 0.469,0.198 10 false 4 5.885,3.396 6.354,3.594 0.469,0.198 10 false R43 5.885,3.583 7.094,4.198 1.208,0.615 10 false Blind Spot Monitor Sensor RH

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor system is on.


PROCEDURE

1.CHECK DTC

b.

Recheck for DTCs and check if the same DTC is output again.

OK:

DTC C1AB3 is not output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - OUTER MIRROR CONTROL ECU ASSEMBLY RH)
2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - OUTER MIRROR CONTROL ECU ASSEMBLY RH)
a.
E383327C02
1.438,0.25 1.938,0.5 0.5,0.25 1.854,1.146 2.24,0.604 2.24,0.604 2.49,0.604 true 1.573,0.292 2.031,0.49 0.458,0.198 10 false R43 0.042,0.031 0.5,0.229 0.458,0.198 10 false *a 2.552,0.521 3.01,0.719 0.458,0.198 10 false OMIR
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH)


Disconnect the blind spot monitor sensor RH connector.


b.

Disconnect the J12 outer mirror control ECU assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R43-4 (OMIR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK OUTER REAR VIEW MIRROR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK OUTER REAR VIEW MIRROR ASSEMBLY RH
a.
E166711C79
0.375,0.781 0.781,1.063 0.406,0.281 2.24,1.01 2.51,1.198 2.51,1.198 2.667,1.198 true 0.479,0.844 0.792,1.042 0.313,0.198 10 false z19 0.115,0.104 0.427,0.302 0.313,0.198 10 false *a 2.74,1.135 3.24,1.333 0.5,0.198 10 false BDIR
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly RH)


Disconnect the outer mirror control ECU assembly RH connector.


b.

Disconnect the IND1 outer mirror RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z19-8 (BDIR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK OUTER MIRROR CONTROL ECU ASSEMBLY RH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

4.CHECK OUTER MIRROR CONTROL ECU ASSEMBLY RH
a.
E297461C28
2.25,0.281 2.646,0.469 0.396,0.188 1.875,1.094 1.635,1.771 1.635,1.771 1.5,1.771 true 2.156,1.292 2.385,1.906 2.385,1.906 2.563,1.906 true 0.063,0.125 0.375,0.281 0.313,0.156 10 false *a 2.323,0.292 2.635,0.448 0.313,0.156 10 false J12 1.156,1.688 1.563,1.865 0.406,0.177 10 false GND 2.615,1.823 3.021,2 0.406,0.177 10 false BDSR
*a Component without harness connected
(Outer Mirror Control ECU Assembly RH)


Disconnect the outer mirror control ECU assembly RH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J12-13 (BDSR) - J12-7 (GND) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK OUTER MIRROR RH

NG

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH

5.CHECK OUTER MIRROR RH
a.


c.

Recheck for DTCs and check if the same DTC is output again.

OK:

DTC C1AB3 is not output.



Result:
Proceed to
OK
NG



OK

END (OUTER MIRROR RH WAS DEFECTIVE)

NG