Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › from 2017.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0261011 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB4  Open in Outer Mirror Indicator(Master)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor LH detects an open in the outer rear view mirror indicator LH.

DTC No. DTC Detection Condition Trouble Area
C1AB4
Both of the following conditions are met:
·

The blind spot monitor system is on

·

The current flowing to the indicator is below a specified value when indicator operation voltage is being sent to the indicator


·

Outer mirror LH (outer rear view mirror indicator LH)

·

Outer rear view mirror assembly LH

·

Harness or connector

·

Blind spot monitor sensor LH

·

Outer mirror control ECU assembly LH



WIRING DIAGRAM

E329056E33
1.563,1.229 1.719,1.427 0.156,0.198 10 false 2 1.583,1.729 1.854,1.938 0.271,0.208 10 false 1 1.375,1.365 1.531,1.563 0.156,0.198 10 false + 1.375,1.823 1.531,2.021 0.156,0.198 10 false - 0.323,2.198 0.979,2.427 0.656,0.229 10 false IND2 0.323,2.344 2.052,2.74 1.729,0.396 10 false Outer Mirror LH (Outer Rear View Mirror Indicator LH) 0.208,3.406 2.688,3.698 2.479,0.292 10 false Outer Rear View Mirror Assembly LH 2.875,1.354 3.344,1.552 0.469,0.198 10 false z18 2.875,1.833 3.344,2.031 0.469,0.198 10 false z18 2.958,1.177 3.208,1.365 0.25,0.188 10 false 8 2.917,1.646 3.385,1.844 0.469,0.198 10 false 12 3.281,1.354 3.75,1.552 0.469,0.198 10 false BDIL 3.281,1.854 3.75,2.052 0.469,0.198 10 false HTR- 3.198,3.406 4.438,3.823 1.24,0.417 10 false Outer Mirror Control ECU Assembly LH 4.021,1.375 4.49,1.573 0.469,0.198 10 false BDSL 4.104,1.833 4.573,2.031 0.469,0.198 10 false GND 4.531,1.354 5,1.552 0.469,0.198 10 false K12 4.542,1.823 5.01,2.021 0.469,0.198 10 false K12 4.583,1.167 5.052,1.365 0.469,0.198 10 false 13 4.604,1.646 5.073,1.844 0.469,0.198 10 false 7 5.969,1.375 6.438,1.573 0.469,0.198 10 false OMIL 5.781,1.25 6.25,1.448 0.469,0.198 10 false 4 5.885,3.396 6.354,3.594 0.469,0.198 10 false R42 5.885,3.583 7.094,4.198 1.208,0.615 10 false Blind Spot Monitor Sensor LH

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor system is on.


PROCEDURE

1.CHECK DTC

b.

Recheck for DTCs and check if the same DTC is output again.

OK:

DTC C1AB4 is not output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - OUTER MIRROR CONTROL ECU ASSEMBLY LH AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - OUTER MIRROR CONTROL ECU ASSEMBLY LH AND BODY GROUND)
a.

Disconnect the R42 blind spot monitor sensor LH connector.


b.

Disconnect the K12 outer mirror control ECU assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R42-4 (OMIL) - K12-13 (BDSL) Always Below 1 Ω
K12-7 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT OUTER MIRROR CONTROL ECU ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT OUTER MIRROR CONTROL ECU ASSEMBLY LH
a.
E297461C29
2.25,0.281 2.646,0.469 0.396,0.188 0.719,0.302 1.115,0.49 0.396,0.188 1.875,1.094 1.833,1.688 1.833,1.688 1.688,1.688 true 2.156,1.292 2.385,1.906 2.385,1.906 2.563,1.906 true 0.292,1.125 0.198,1.781 0.198,1.781 0.344,1.781 true 0.969,1.313 0.958,1.958 0.958,1.958 1.115,1.958 true 0.104,0.042 0.417,0.198 0.313,0.156 10 false *a 2.323,0.302 2.635,0.458 0.313,0.156 10 false K12 1.344,1.615 1.75,1.792 0.406,0.177 10 false GND 2.635,1.823 3.042,2 0.406,0.177 10 false BDSL 0.823,0.313 1.135,0.469 0.313,0.156 10 false z18 0.406,1.708 1.021,1.885 0.615,0.177 10 false BDIL 1.198,1.865 1.823,2.063 0.625,0.198 10 false HTR-
*a Component without harness connected
(Outer Mirror Control ECU Assembly LH)


Remove the outer mirror control ECU assembly LH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR CONTROL ECU>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K12-13 (BDSL) - z18-8 (BDIL) Always Below 1 Ω
K12-7 (GND) - z18-12 (HTR-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK OUTER REAR VIEW MIRROR ASSEMBLY LH

NG

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY LH

4.CHECK OUTER REAR VIEW MIRROR ASSEMBLY LH
a.

Disconnect the z18 outer mirror control ECU assembly LH connector.


b.

Disconnect the IND2 outer mirror LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z18-8 (BDIL) - IND2-2 (+) Always Below 1 Ω
z18-12 (HTR-) - IND1-2 (-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK OUTER MIRROR LH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

5.CHECK OUTER MIRROR LH
a.


c.

Recheck for DTCs and check if the same DTC is output again.

OK:

DTC C1AB4 is not output.



Result:
Proceed to
OK
NG



OK

END (OUTER MIRROR LH WAS DEFECTIVE)

NG