Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › from 2017.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0261011 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB5  Open in Outer Mirror Indicator(Slave)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor RH detects an open in the outer rear view mirror indicator RH.

DTC No. DTC Detection Condition Trouble Area
C1AB5
Both of the following conditions are met:
·

The blind spot monitor system is on

·

The current flowing to the indicator is below a specified value when indicator operation voltage is being sent to the indicator


·

Outer mirror RH (outer rear view mirror indicator RH)

·

Outer rear view mirror assembly RH

·

Harness or connector

·

Blind spot monitor sensor RH

·

Outer mirror control ECU assembly RH



WIRING DIAGRAM

E329056E34
1.563,1.229 1.719,1.427 0.156,0.198 10 false 2 1.583,1.729 1.854,1.938 0.271,0.208 10 false 1 1.375,1.365 1.531,1.563 0.156,0.198 10 false + 1.375,1.823 1.531,2.021 0.156,0.198 10 false - 0.323,2.198 0.979,2.427 0.656,0.229 10 false IND1 0.323,2.344 2.052,2.74 1.729,0.396 10 false Outer Mirror RH (Outer Rear View Mirror Indicator RH) 0.208,3.406 2.688,3.698 2.479,0.292 10 false Outer Rear View Mirror Assembly RH 2.875,1.354 3.344,1.552 0.469,0.198 10 false z19 2.875,1.833 3.344,2.031 0.469,0.198 10 false z19 2.958,1.177 3.208,1.365 0.25,0.188 10 false 8 2.917,1.646 3.385,1.844 0.469,0.198 10 false 12 3.281,1.354 3.75,1.552 0.469,0.198 10 false BDIR 3.281,1.854 3.75,2.052 0.469,0.198 10 false HTR- 3.198,3.406 4.438,3.823 1.24,0.417 10 false Outer Mirror Control ECU Assembly RH 4.021,1.375 4.49,1.573 0.469,0.198 10 false BDSR 4.104,1.833 4.573,2.031 0.469,0.198 10 false GND 4.531,1.354 5,1.552 0.469,0.198 10 false J12 4.542,1.823 5.01,2.021 0.469,0.198 10 false J12 4.583,1.167 5.052,1.365 0.469,0.198 10 false 13 4.604,1.646 5.073,1.844 0.469,0.198 10 false 7 5.969,1.375 6.438,1.573 0.469,0.198 10 false OMIR 5.781,1.25 6.25,1.448 0.469,0.198 10 false 4 5.885,3.396 6.354,3.594 0.469,0.198 10 false R43 5.885,3.583 7.094,4.198 1.208,0.615 10 false Blind Spot Monitor Sensor RH

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor system is on.


PROCEDURE

1.CHECK DTC

b.

Recheck for DTCs and check if the same DTC is output again.

OK:

DTC C1AB5 is not output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - OUTER MIRROR CONTROL ECU ASSEMBLY RH AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - OUTER MIRROR CONTROL ECU ASSEMBLY RH AND BODY GROUND)
a.

Disconnect the R43 blind spot monitor sensor RH connector.


b.

Disconnect the J12 outer mirror control ECU assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R43-4 (OMIR) - J12-13 (BDSR) Always Below 1 Ω
J12-7 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT OUTER MIRROR CONTROL ECU ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT OUTER MIRROR CONTROL ECU ASSEMBLY RH
a.
E297461C30
2.25,0.281 2.646,0.469 0.396,0.188 0.719,0.302 1.115,0.49 0.396,0.188 1.885,1.094 1.833,1.688 1.833,1.688 1.688,1.688 true 2.156,1.292 2.385,1.906 2.385,1.906 2.563,1.906 true 0.406,1.125 0.49,1.792 0.49,1.792 0.635,1.792 true 0.969,1.313 1.198,1.927 1.198,1.927 1.375,1.927 true 0.104,0.042 0.417,0.198 0.313,0.156 10 false *a 2.344,0.302 2.656,0.458 0.313,0.156 10 false J12 1.365,1.604 1.771,1.781 0.406,0.177 10 false GND 2.604,1.844 3.01,2.021 0.406,0.177 10 false BDSR 0.792,0.313 1.104,0.469 0.313,0.156 10 false z19 0.688,1.729 1.354,1.917 0.667,0.188 10 false BDIR 1.427,1.865 1.833,2.042 0.406,0.177 10 false HTR-
*a Component without harness connected
(Outer Mirror Control ECU Assembly RH)


Remove the outer mirror control ECU assembly RH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR CONTROL ECU>REMOVAL


b.

Disconnect the outer rear view mirror assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J12-13 (BDSR) - z19-8 (BDIR) Always Below 1 Ω
J12-7 (GND) - z19-12 (HTR-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK OUTER REAR VIEW MIRROR ASSEMBLY RH

NG

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH

4.CHECK OUTER REAR VIEW MIRROR ASSEMBLY RH
a.

Disconnect the z19 outer mirror control ECU assembly RH connector.


b.

Disconnect the IND1 outer rear view mirror RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z19-8 (BDIR) - IND1-2 (+) Always Below 1 Ω
z19-12 (HTR-) - IND1-1 (-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK OUTER MIRROR RH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

5.CHECK OUTER MIRROR RH
a.


c.

Recheck for DTCs and check if the same DTC is output again.

OK:

DTC C1AB5 is not output.



Result:
Proceed to
OK
NG



OK

END (OUTER MIRROR RH WAS DEFECTIVE)

NG