Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM (w/ VSC) › from 2017.08
RM27T0E _55 Steering _053717 POWER ASSIST SYSTEMS _0260945 POWER STEERING SYSTEM(w/ VSC) J

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM(w/ VSC)  Power Steering Warning Light Circuit  


DESCRIPTION

The power steering ECU is connected to the combination meter via CAN communication. If the power steering ECU detects a malfunction, the power steering warning light comes on. At this time, the vehicle enters fail-safe mode.

WIRING DIAGRAM

C216948E14
0.521,3.896 1.885,4.094 1.365,0.198 10 false Combination Meter 5.51,3.896 6.958,4.177 1.448,0.281 10 false Power Steering ECU 3.927,2.083 5.052,2.323 1.125,0.24 10 false ECU-IG NO. 1 1.448,4.375 3.479,4.646 2.031,0.271 10 false CAN Communication System 2.063,1.938 3.104,2.188 1.042,0.25 10 false from IG Circuit 5.802,1.958 6.094,2.156 0.292,0.198 10 false IG 5.781,2.938 6.135,3.135 0.354,0.198 10 false GND 5.531,1.781 5.729,1.99 0.198,0.208 10 false 5 5.531,2.792 5.729,3.021 0.198,0.229 10 false 3 0.51,3.76 0.802,3.958 0.292,0.198 10 false G6 5.51,3.75 5.865,3.948 0.354,0.198 10 false G46

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.INSPECT CAN COMMUNICATION SYSTEM
a.

Check for DTCs of the CAN communication system.

Refer to the following procedures (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSTIC TROUBLE CODE CHART).

Result
Result Proceed to
DTC is not output. A
DTC is output. B



A

2.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU - BATTERY AND BODY GROUND)

B

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

2.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU - BATTERY AND BODY GROUND)
a.
U148442E01
0.067,0.021 0.259,0.177 0.193,0.156 10 *a 1.445,1.333 1.095,1.671 false 1.824,1.333 2.174,1.671 false 2.123,1.668 2.358,1.838 0.235,0.170 10 IG 0.91,1.668 1.297,1.819 0.387,0.151 10 GND 1.563,0.284 2.121,0.448 0.558,0.164 10 G46

Disconnect the power steering ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G46-5 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G46-3 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Power Steering ECU)



OK

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (METER/GAUGE SYSTEM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (METER/GAUGE SYSTEM)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the intelligent tester on.


c.

Perform the Active Test of the combination meter using the intelligent tester (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

Combination Meter
Tester Display Test Part Control Range Diagnostic Note
PPS Indicator Power steering warning light ON or OFF Perform the test with the vehicle stopped and the engine idling.


d.

Check that the power steering warning light operates in accordance with the Active Test.

HINT:

Reconnect the connectors and restore the vehicle to its previous condition before checking the combination meter.


OK:

The power steering warning light turns on and off in accordance with the intelligent tester operation.




OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

INSPECT METER/GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)