Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2018.06–2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P023B  Charge Air Cooler Coolant Pump Control Circuit Low  


DESCRIPTION

The intercooler cooling system is a water cooling system that is independent from the engine cooling system. It uses a dedicated radiator and electric water pump assembly to cool the intercooler and turbocharger. The electric water pump assembly uses the duty cycle signals sent from the ECM to provide stepless, optimal control of the electric water pump assembly speed.

P023B
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
After fully warming up, increase and maintain the engine speed so that the intercooler water pump duty ratio is 30% or more for 3 seconds or longer. Electric water pump assembly output voltage is specified value or less (1 trip detection logic).
·

Electric water pump assembly circuit

·

Electric water pump assembly

·

ECM



MONITOR DESCRIPTION

The ECM calculates the speed of the electric water pump assembly by using the rotational duty signal (IWPI) sent from the electric water pump assembly.

The electric water pump assembly is controlled steplessly by the drive duty signal (IWPO) output from the ECM.

The ECM monitors the actual drive duty cycle signal (IWPO) while simultaneously outputting the drive duty signal (IWPO) to the electric water pump assembly.

If the actual drive duty signal (IWPO) is less than or equal to the threshold value while the drive duty signal (IWPO) is being output to the electric water pump assembly, the ECM detects a malfunction and stores a DTC.

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (CONTROL THE INTERCOOLER WATER PUMP)
a.

Disconnect the electric water pump assembly connector.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Active Test / Control the Intercooler Water Pump.


f.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
B15-3 (SWP) - Body ground Before Active Test → Active Test in progress Before Active Test:
Resistance stabilized → Active Test in progress:
Resistance changes*

HINT:

*: The transistor inside the ECM is controlled by performing the Active Test.

The resistance of the SWP terminal changes while the Active Test is in progress due to duty control.

If the resistance fluctuates while the Active Test is being performed from the resistance that stabilized before the Active Test was performed, it can be judged that the transistor is operating.

If the transistor does not operate while the Active Test is being performed, the ECM may be malfunctioning.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ELECTRIC WATER PUMP ASSEMBLY - ECM)

NG

2.CHECK HARNESS AND CONNECTOR (ELECTRIC WATER PUMP ASSEMBLY - ECM)
a.

Disconnect the electric water pump assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B15-3 (SWP) - G184-32 (IWPO) Always Below 1 Ω
B15-3 (SWP) or G184-32 (IWPO) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR