Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2018.06–2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P023A  Charge Air Cooler Coolant Pump Control Circuit/Open  


DESCRIPTION

P023A
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
After fully warming up, drive the vehicle at approximately 50 km/h for 10 minutes or more. When any condition below is met.
·

Overspeed:

The rotational speed of the pump is higher than the upper limit value for 75 seconds or more while the electric water pump assembly is operating.

(2 trip detection logic)

·

Stuck:

The rotational speed of the pump is less than the lower limit value for 75 seconds or more while the electric water pump assembly is operating.

(2 trip detection logic)

·

Open circuit:

The rotational speed calculated from the IWPI signal is 15 seconds or more and 10 rpm or less.

(Open or short in IWPI circuit)

(1 trip detection logic)


Overspeed
·

Insufficient coolant (for Intercooler)

·

Coolant leak (for Intercooler)

·

Electric water pump assembly

·

Electric water pump assembly


Stuck
·

Electric water pump assembly


Open circuit
·

Electric water pump assembly

·

EFI-MAIN NO. 2 relay

·

Wire harness and connector

·

ECM



MONITOR DESCRIPTION

The ECM calculates the speed of the electric water pump assembly by using the rotational duty signal (IWPI) sent from the electric water pump assembly.

A 4 Hz duty signal (IWPI) is output even when the pump is stopped. The ECM then converts the electric water pump assembly rotational duty signal (IWPI) into the rotational speed and checks that it is 160 rpm when the pump is stopped.

When the speed of the electric water pump assembly is below 10 rpm, the system judges that there is an open or short circuit in the IWPI terminal.

If the actual speed exceeds the target speed by a fixed value or more, the ECM evaluates overspeed operation. If the actual speed is below the target speed by a fixed value or more, the ECM evaluates that the motor is stuck. In these cases it stores a DTC.

WIRING DIAGRAM

A426491E01
4.26,4.583 4.927,5.042 0.667,0.458 10 false EFI MAIN NO. 3 3.365,4.542 4,4.885 0.635,0.344 10 false EFI MAIN NO. 2 3.167,5.698 4.26,6.031 1.094,0.333 10 false EFI MAIN NO. 1 2.313,5.167 3.406,5.5 1.094,0.333 10 false EFI MAIN NO. 1 2.292,4.052 3.448,4.375 1.156,0.323 10 false EFI MAIN NO. 2 4.823,3.875 5.135,4.073 0.313,0.198 10 false 1W 4.823,5.365 5.135,5.563 0.313,0.198 10 false 1W 1.302,3.875 1.615,4.073 0.313,0.198 10 false 1S 1.292,5.365 1.604,5.563 0.313,0.198 10 false 1W 1.385,3.688 1.542,3.885 0.156,0.198 10 false 1 4.885,5.188 5.042,5.385 0.156,0.198 10 false 8 4.896,3.688 5.052,3.885 0.156,0.198 10 false 3 5.542,5.135 5.969,5.344 0.427,0.208 10 false 14 5.448,5.365 6.01,5.563 0.563,0.198 10 false G184 5.875,5.365 6.781,5.615 0.906,0.25 10 false MREL 6.271,6.083 6.813,6.417 0.542,0.333 10 false ECM 0.563,6.052 1.76,6.375 1.198,0.323 10 false Battery 0.427,4.76 1.625,5.083 1.198,0.323 10 false 70A FL 5.458,0.635 6.146,0.833 0.688,0.198 10 false G184 5.865,1.302 7.156,1.521 1.292,0.219 10 false IWPI 5.865,0.51 7.156,0.719 1.292,0.208 10 false IWPO 5.552,0.406 5.865,0.604 0.313,0.198 10 false 32 5.563,1.188 5.875,1.385 0.313,0.198 10 false 19 4.25,1.438 4.688,1.635 0.438,0.198 10 false NWP 3.708,1.427 4.167,1.625 0.458,0.198 10 false GND 1.365,5.188 1.521,5.385 0.156,0.198 10 false 4 3.542,2.01 4.792,2.385 1.25,0.375 10 false Electric water pump assembly 3.552,1.844 3.865,2.042 0.313,0.198 10 false B15 2.26,0.823 3.208,1.146 0.948,0.323 10 false EFI No. 2 3.688,0.656 4.167,0.833 0.479,0.177 10 false +BWP 4.229,0.646 4.708,0.844 0.479,0.198 10 false SWP 4.667,0.51 4.823,0.708 0.156,0.198 10 false 3 3.51,1.292 3.688,1.531 0.177,0.24 10 false 1 4.698,1.302 4.875,1.542 0.177,0.24 10 false 2 3.49,0.521 3.667,0.76 0.177,0.24 10 false 4 2.25,0.51 2.427,0.75 0.177,0.24 10 false 1 2.729,0.51 2.906,0.75 0.177,0.24 10 false 2 5.448,1.438 6.281,1.646 0.833,0.208 10 false G185 2.188,6.083 5.271,6.427 3.083,0.344 10 false No. 1 Integration Relay

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

P023A may be detected if operation continues when the coolant (for intercooler) is insufficient. If there is sufficient coolant (for intercooler) and P023A is output when the vehicle is brought to the workshop, check if the customer has added extra coolant to the intercooler in the past.

·

If the electric water pump assembly voltage is high or low, control may be temporarily stopped and P023A output. When the high- or low-voltage status situation is resolved, the temporarily halted control returns to normal. Therefore, it is not necessary to replace the electric water pump assembly.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P023A)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Result:
Result Proceed to
DTC P023A is output A
DTC P023A other DTCs are output B


HINT:

If any DTCs other than P023A are output, troubleshoot those DTCs first.




A

2.CHECK COOLANT LEVEL AT RESERVOIR

B

2.CHECK COOLANT LEVEL AT RESERVOIR

Result:
Result Proceed to
At or below reservoir tank LOW level. A
At or above reservoir tank LOW level. B



A

3.CHECK FOR COOLANT LEAK

B

5.BLEED AIR
3.CHECK FOR COOLANT LEAK
a.

Check the turbocharger and intercooler cooling system for coolant leaks.

Click hereEngine / Hybrid System>1GD-FTV (INTAKE / EXHAUST)>COOLANT (w/ Urea SCR System)>ON-VEHICLE INSPECTION

OK:

No leaks.



Result:
Proceed to
OK
NG



OK

5.BLEED AIR

NG

4.REPAIR COOLANT LEAK
4.REPAIR COOLANT LEAK
a.

Repair any coolant leaks.


Result:
Proceed to
NEXT



NEXT

5.BLEED AIR
5.BLEED AIR
a.

Bleed the air and add coolant up to the FULL Line on the reservoir tank.

Click hereEngine / Hybrid System>1GD-FTV (INTAKE / EXHAUST)>COOLANT (w/ Urea SCR System)>REPLACEMENT


Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P023A)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P023A)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.



d.

Turn the engine switch off and wait for at least 30 seconds.


e.

Start the engine, turn off all accessory switches and warm up the engine until the engine coolant temperature stabilizes.

(Engine coolant temperature at 75°C or more)


f.

Drive the vehicle at approximately 50 km/h for 10 minutes or more.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Result:
Result Proceed to
DTC P023A is output A
DTC is not output B


HINT:

If the DTC is no longer output, it may have been output due to idling as a result insufficient intercooler coolant.




A

7.PERFORM ACTIVE TEST USING GTS (CONTROL THE INTERCOOLER WATER PUMP)

B

END

7.PERFORM ACTIVE TEST USING GTS (CONTROL THE INTERCOOLER WATER PUMP)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Active Test / Control the Intercooler Water Pump.


e.

Perform the Active Test. Check that the electric water pump assembly is operating (vibrating).

OK:

The electric water pump assembly is operating (vibrating).


HINT:

Use a sound scope if the operation is difficult to check.



Result:
Proceed to
OK
NG



OK

8.CHECK ECM (IWPI VOLTAGE)

NG

10.CHECK HARNESS AND CONNECTOR (ELECTRIC WATER PUMP ASSEMBLY - BODY GROUND)
8.CHECK ECM (IWPI VOLTAGE)
a.
A420084C01
0.375,1.042 0.813,1.323 0.438,0.281 1.167,1.635 1.583,1.219 true 0.448,1.094 0.958,1.313 0.51,0.219 11 false B15 0.052,0.042 0.365,0.24 0.313,0.198 10 false *a 0.906,1.677 1.365,1.875 0.458,0.198 10 false NWP
*a Front view of wire harness connector
(to Electric Water Pump Assembly)


Disconnect the electric water pump assembly connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B15-2 (NWP) - Body ground Engine switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

9.CHECK HARNESS AND CONNECTOR (ELECTRIC WATER PUMP ASSEMBLY - ECM)
9.CHECK HARNESS AND CONNECTOR (ELECTRIC WATER PUMP ASSEMBLY - ECM)
a.

Disconnect the electric water pump assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B15-2 (NWP) - G185-19 (IWPI) Always Below 1 Ω
B15-2 (NWP) or G185-19 (IWPI) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (ELECTRIC WATER PUMP ASSEMBLY - BODY GROUND)
a.

Disconnect the electric water pump assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B15-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

11.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ELECTRIC WATER PUMP ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ELECTRIC WATER PUMP ASSEMBLY)
a.
A420084C02
0.375,1.042 0.813,1.323 0.438,0.281 2.375,1.677 2.073,1.188 true 0.448,1.094 0.958,1.313 0.51,0.219 11 false B15 0.052,0.042 0.365,0.24 0.313,0.198 10 false *a 2.448,1.698 3.115,1.906 0.667,0.208 10 false +BWP
*a Front view of wire harness connector
(to Electric Water Pump Assembly)


Disconnect the electric water pump assembly connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B15-4 (+BWP) - Body ground Engine switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE ELECTRIC WATER PUMP ASSEMBLY

NG

12.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ELECTRIC WATER PUMP ASSEMBLY)
12.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ELECTRIC WATER PUMP ASSEMBLY)
a.

Remove the No. 1 integration relay from the engine room relay block.


b.

Disconnect the electric water pump assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1W-3 - B15-4 (+BWP) Always Below 1 Ω
1W-3 or B15-4 (+BWP) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.INSPECT NO. 1 INTEGRATION RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.INSPECT NO. 1 INTEGRATION RELAY

Result:
Proceed to
OK
NG



OK

NG

REPLACE NO. 1 INTEGRATION RELAY