Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2018.06–2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P200C  Diesel Particulate Filter Temperature Too High Bank 1  P200E  Catalyst System Temperature Too High Bank 1  P2428  Exhaust Gas Temperature Too High Bank 1  


DESCRIPTION

A351107E02
2.823,1.583 3.021,1.146 3.021,1.146 3.167,1.146 false 2.979,2.208 3.094,1.99 3.094,1.99 3.188,1.99 false 2.823,2.979 2.979,2.781 2.979,2.781 3.104,2.781 false 2.833,3.25 2.927,3.448 2.927,3.448 3.031,3.448 false 2.396,2.479 2.052,2.604 2.052,2.604 2.052,2.708 false 0.271,0.656 0.479,0.854 0.208,0.198 10 false *a 3.219,1.073 3.417,1.323 0.198,0.25 10 false *4 3.25,1.906 3.49,2.083 0.24,0.177 10 false *5 3.156,2.719 3.406,2.885 0.25,0.167 10 false *6 1.99,2.76 2.208,2.979 0.219,0.219 10 false *3 6.208,1.792 6.563,2 0.354,0.208 10 false *8 1.542,1.646 1.76,1.813 0.219,0.167 10 false *2 3.094,3.385 3.313,3.573 0.219,0.188 10 false *7 0.833,0.375 1.052,0.542 0.219,0.167 10 false *1

*1 Exhaust Fuel Addition Injector Assembly *2 Turbocharger Sub-assembly
*3 DPF Catalyst *4 Exhaust Gas Temperature Sensor
*5 No. 2 Exhaust Gas Temperature Sensor *6 No. 3 Exhaust Gas Temperature Sensor
*7 No. 1 Nitrogen Oxides Sensor *8 ECM
*a Exhaust Gas - -

The exhaust fuel addition injector assembly is mounted on the exhaust manifold, and low pressure fuel is supplied to the exhaust fuel addition injector assembly by the feed pump in the fuel supply pump assembly. This injector adds fuel in response to a control signal from the ECM, in order to perform PM forced regeneration.

During PM forced regeneration, the exhaust fuel addition injector adds fuel to raise the DPF* catalyst temperature.

*: Diesel Particulate Filter

This injector adds fuel by a control signal from the ECM.

This injector is used for two different controls: PM forced regeneration and PM reduction.

During PM forced regeneration, the injector adds fuel to raise the catalyst temperature.

In the other control, the injector helps the air-fuel ratio become rich. As a result, PM in the exhaust gas will be reduced in response to the rich air-fuel ratio.

HINT:
·

For more information on the exhaust fuel addition injector and DPF, refer to the following procedures.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>SYSTEM DESCRIPTION

·

If DTC P200C, P200E and P2428 are present, refer to the diagnostic trouble code (DTC) chart for Diesel Particulate Filter System.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>SYSTEM DESCRIPTION



P200C
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
PM forced regeneration*
*: When P200C is detected due to a DPF catalyst problem such as thermal degradation, because the malfunction cannot be duplicated even if the vehicle is driven after PM forced regeneration is performed, perform troubleshooting by following the diagnosis procedure and checking the freeze frame data.
The value of "Exhaust Temperature B1S3" is higher than 1000°C (1832°F) for 5 seconds.
(1 trip detection logic)
Main Trouble Area
·

Open or short in exhaust fuel addition injector assembly

·

Exhaust fuel addition injector assembly

·

Exhaust manifold converter sub-assembly (DPF catalyst)


Sub Trouble Area
·

No. 3 exhaust gas temperature sensor

·

No. 1 nitrogen Oxides Sensor

·

Mass air flow meter sub-assembly

·

Manifold absolute pressure sensor

·

Fuel leaks or blockages in exhaust fuel addition injector assembly

·

Fuel supply pump assembly

·

Injector assembly

·

Blockages or leaks in air intake system

·

Blockages or leaks in exhaust system

·

Blockages or leaks in EGR system

·

ECM


Common Inspection Item:
·

Fuel injection system

·

Intake/Exhaust system

·

After treatment control system



P200E
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
PM forced regeneration*
*: When P200E is detected due to a DPF catalyst problem such as thermal degradation, because the malfunction cannot be duplicated even if the vehicle is driven after PM forced regeneration is performed, perform troubleshooting by following the diagnosis procedure and checking the freeze frame data.
The value of "Exhaust Temperature B1S2" is higher than 1000°C (1832°F) for 5 seconds.
(1 trip detection logic)
Main Trouble Area
·

Open or short in exhaust fuel addition injector assembly

·

Exhaust fuel addition injector assembly

·

Exhaust manifold converter sub-assembly (DPF catalyst)


Sub Trouble Area
·

No. 2 exhaust gas temperature sensor

·

No. 1 nitrogen Oxides Sensor

·

Mass air flow meter sub-assembly

·

Manifold absolute pressure sensor

·

Fuel leaks or blockages in exhaust fuel addition injector assembly

·

Fuel supply pump assembly

·

Injector assembly

·

Blockages or leaks in air intake system

·

Blockages or leaks in exhaust system

·

Blockages or leaks in EGR system

·

ECM


Common Inspection Item:
·

Fuel injection system

·

Intake/Exhaust system

·

After treatment control system



P2428
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
PM forced regeneration*
*: When P2428 is detected due to a DPF catalyst problem such as thermal degradation, because the malfunction cannot be duplicated even if the vehicle is driven after PM forced regeneration is performed, perform troubleshooting by following the diagnosis procedure and checking the freeze frame data.
The value of "Exhaust Temperature B1S1" is higher than 1000°C (1832°F) for 5 seconds.
(1 trip detection logic)
Main Trouble Area
·

Open or short in exhaust fuel addition injector assembly

·

Exhaust fuel addition injector assembly

·

Exhaust manifold converter sub-assembly (DPF catalyst)


Sub Trouble Area
·

Exhaust gas temperature sensor

·

No. 1 nitrogen Oxides Sensor

·

Mass air flow meter sub-assembly

·

Manifold absolute pressure sensor

·

Fuel leaks or blockages in exhaust fuel addition injector assembly

·

Fuel supply pump assembly

·

Injector assembly

·

Blockages or leaks in air intake system

·

Blockages or leaks in exhaust system

·

Blockages or leaks in EGR system

·

ECM


Common Inspection Item:
·

Fuel injection system

·

Intake/Exhaust system

·

After treatment control system



HINT:
·

Due to fail-safe operation when other DTCs (that involve the engine power limit) are stored, PM forced regeneration may be prohibited.

This DTC or P0420, P20CF, P244B and P2463 may be stored due to the fact that PM forced regeneration is prohibited due to the fail-safe operation of other DTCs.

·

The air-fuel ratio and the exhaust gas temperature can be checked by entering the following menus on the GTS: Powertrain / Engine and ECT / Data List / Diesel Exhaust / AF Lambda B1S1, Exhaust Temperature B1S1, Exhaust Temperature B1S2 and Exhaust Temperature B1S3.

·

Malfunctions in the engine itself may affect the DPF system control and cause storage of this DTC. For example, malfunctions in the injector assemblies that cause a large amount of smoke emission: These affect the exhaust fuel addition injector assembly operation. Blockages or leaks in the air intake system, or an EGR system malfunction such as EGR passage blockages: These malfunctions affect the DPF catalyst temperature control. Therefore, the engine condition itself should also be checked, in addition to the exhaust fuel addition injector assembly.



Related Data List
DTC No. Data List
P200C
P200E
P2428
·

MAF

·

MAP

·

Intake Air Temp (Turbo)

·

Target Booster Pressure

·

Atmosphere Pressure

·

Coolant Temp

·

Engine Speed

·

AF Lambda B1S1

·

Exhaust Fuel Addition FB

·

Exhaust Temperature B1S1

·

Exhaust Temperature B1S2

·

Exhaust Temperature B1S3

·

Catalyst Differential Press

·

Injection Feedback Val #1 to #4

·

Injection Volume



MONITOR DESCRIPTION

The ECM monitors DPF catalyst temperature. When the temperature becomes high due to uncombusted fuel, engine oil or thermal degradation to the DPF catalyst, the ECM illuminates the MIL.

A244058E12
3.969,1.167 3.26,0.406 false 3.26,0.406 3.094,0.406 false 0.104,0 1.542,0.333 1.438,0.333 10 false Malfunction Detection: 0.125,1.76 1.51,2.417 1.385,0.656 10 false Exhaust Temperature B1S1, B1S2 or B1S3 3.865,0.531 4.719,0.865 0.854,0.333 10 false MIL Goes On 5.792,1.104 6.99,1.49 1.198,0.385 10 false P200C, P200E and P2428 Threshold 2.5,0.344 3.125,0.677 0.625,0.333 10 false Abnormal 3.219,1.927 5.688,2.115 2.469,0.188 10 false Normal (500 to 700°C (932 to 1292°F)) 5.594,1.813 6.073,2.146 0.479,0.333 10 false Normal

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing an injector assembly, the ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ OUTPUT DTC (RECORD STORED DTC AND FREEZE FRAME DATA) (PROCEDURE 1)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch to on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Record the stored DTC and freeze frame data.



NEXT

2.REPLACE EXHAUST GAS TEMPERATURE SENSOR
2.REPLACE EXHAUST GAS TEMPERATURE SENSOR
a.

Confirm "Exhaust Temperature B1S1", "Exhaust Temperature B1S2" and "Exhaust Temperature B1S3" in the freeze frame data which was recorded in step 1 and determine which exhaust gas temperature sensor to replace.

Result
Result Items to be Replaced
Exhaust Temperature B1S1 value is 850°C (1562°F) or more Exhaust gas temperature sensor
Exhaust Temperature B1S2 value is 850°C (1562°F) or more No. 2 exhaust gas temperature sensor
Exhaust Temperature B1S3 value is 850°C (1562°F) or more No. 3 exhaust gas temperature sensor


b.

If DTC P200C, P200E and/or P2428 is output, the exhaust gas temperature sensors need to be replaced. However, make sure to perform all diagnostic procedures for P200C, P200E and/or P2428 before replacing the exhaust gas temperature sensors.

HINT:

If the exhaust gas temperature sensors are subjected to an abnormally high temperature, the internal resistance of the sensor increases. This causes incorrect temperature measurement.




NEXT

3.CHECK FOR BLACK SMOKE
3.CHECK FOR BLACK SMOKE
a.

Start the engine and drive the vehicle until the engine coolant temperature reaches 75°C (167°F) or higher.


b.

Stop the vehicle and allow the engine to idle.


c.

Fully depress the accelerator pedal for 5 seconds, and then release it [A].


d.

Repeat the above procedure [A] 10 times [B].


e.

Check for black smoke emission during procedure [A] and [B].

OK:

Black smoke is emitted less than 5 times.


HINT:

Even if the black smoke is very thin, count the number of black smoke emissions if there is any visible smoke.




OK

5.CHECK FUEL INJECTION SYSTEM

NG

4.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
4.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
a.

Even though it has been determined that the exhaust manifold converter sub-assembly (DPF catalyst) needs to be replaced, make sure to perform all diagnostic procedures for DTC P200C, P200E and/or P2428 before replacing it.

HINT:

This DTC is stored because an excessive amount of PM has accumulated and resulted in abnormal combustion. It is necessary to diagnose the cause of abnormal PM accumulation and repair the problem. Therefore, do not perform replacement at this time.




NEXT

5.CHECK FUEL INJECTION SYSTEM
5.CHECK FUEL INJECTION SYSTEM

NEXT

6.CHECK INTAKE / EXHAUST SYSTEM
6.CHECK INTAKE / EXHAUST SYSTEM

NEXT

7.CHECK AFTER TREATMENT CONTROL SYSTEM
7.CHECK AFTER TREATMENT CONTROL SYSTEM

NEXT

8.REPLACE MALFUNCTIONING PARTS
8.REPLACE MALFUNCTIONING PARTS
HINT:

Replace the following items only when it has been determined necessary based on diagnosis for DTC P200C, P200E and/or P2428.


a.

Replace the exhaust manifold converter sub-assembly.

Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>MONOLITHIC CONVERTER (w/ DPF)>REMOVAL

NOTICE:

Perform Initialization procedure for Catalyst Record Clear and DPF Deterioration Record Clear.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION







NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.





NEXT

END