Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › NITROGEN OXIDES SENSOR › from 2018.06
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260460 NITROGEN OXIDES SENSOR A

1GD-FTV ENGINE CONTROL  NITROGEN OXIDES SENSOR  INSTALLATION  


PROCEDURE

Hide 89463D 1.INSTALL NO. 2 NITROGEN OXIDES SENSOR

a.

Install the No. 2 nitrogen oxides sensor with the 2 nuts to the exhaust sensor clamp bracket, and attach the 2 clamps.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.
A424381C01
1.542,0.854 1.906,0.375 1.906,0.375 2.083,0.375 true 0.417,0.823 0.656,1 0.24,0.177 10 true *a 2.167,0.313 2.49,0.5 0.323,0.188 10 true SST
*a Torque Wrench Fulcrum Length


Using SST, install the No. 2 nitrogen oxides sensor.

SST
09224-00012  

Torque:
Specified tightening torque : 55 N*m (561 kgf*cm, 41 ft.*lbf)

NOTICE:

Replace with a new part if it is dropped or if it receives a strong impact.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 255 mm (10.0 in.)): 49.2 N*m (502 kgf*cm, 36 ft.*lbf)




c.

Install the controller portion (exhaust sensor clamp bracket) with the 2 bolts, and then attach the connector and 5 clamps.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)

NOTICE:

Complete the installation so that there is no tension or slack in the harness of the No. 2 nitrogen oxides sensor, and there is no interference.



Hide 89463C 2.INSTALL NO. 1 NITROGEN OXIDES SENSOR

a.

Install the No. 1 nitrogen oxides sensor with the 2 nuts to the exhaust sensor clamp bracket, and attach the clamp (cable tie).

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.
A424389C01
1.698,1.021 2.146,1.875 2.146,1.875 2.313,1.875 true 0.594,0.615 0.906,0.771 0.313,0.156 10 false *a 2.406,1.802 2.76,1.958 0.354,0.156 10 false SST
*a Torque Wrench Fulcrum Length


Using SST, install the No. 1 nitrogen oxides sensor.

SST
09224-00012  

Torque:
Specified tightening torque : 55 N*m (561 kgf*cm, 41 ft.*lbf)

NOTICE:

Replace with a new part if it is dropped or if it receives a strong impact.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 255 mm (10.0 in.)): 49.2 N*m (502 kgf*cm, 36 ft.*lbf)




Hide 25051 3.INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY