Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2018.06–2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P2470  Exhaust Gas Temperature Sensor Circuit Low (Bank 1 Sensor 4)  P2471  Exhaust Gas Temperature Sensor Circuit High (Bank 1 Sensor 4)  


DESCRIPTION

A362192E04
2.031,1.99 2.26,2.49 2.26,2.49 2.406,2.49 true 3.365,2.01 3.594,2.51 3.594,2.51 3.74,2.51 true 4.135,2.01 4.26,2.26 4.26,2.26 4.448,2.26 true 4.792,1.344 4.323,0.542 4.323,0.542 4.177,0.542 true 0.396,1.5 1.01,1.698 0.615,0.198 10 false Exhaust Gas 2.458,2.417 3.563,2.625 1.104,0.208 10 false SCR Catalyst 1.688,0.469 4.302,0.719 2.615,0.25 10 false No. 4 Exhaust Gas Temperature Sensor 6.073,0.99 6.573,1.25 0.5,0.26 10 false ECM 3.781,2.448 4.854,2.677 1.073,0.229 10 false SCR Catalyst 4.521,2.208 5.625,2.417 1.104,0.208 10 false SCR Catalyst

The No. 4 exhaust gas temperature sensor is installed after the SCR catalyst to detect the exhaust gas temperature. A thermistor built into the No. 4 exhaust gas temperature sensor changes its resistance value according to the exhaust gas temperature. The lower the exhaust gas temperature, the higher the thermistor resistance value. The higher the exhaust gas temperature, the lower the thermistor resistance value. The No. 4 exhaust gas temperature sensor is connected to the ECM. The 5 V power source voltage is applied to the No. 4 exhaust gas temperature sensor from terminal THSO via resistor R. Resistor R and the No. 4 exhaust gas temperature sensor are connected in series. When the resistance value of the No. 4 exhaust gas temperature sensor changes in accordance with the exhaust gas temperature, the voltage at terminal THSO also changes. The No. 4 exhaust gas temperature sensor monitors the temperature downstream of the SCR catalyst.

P2470
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Idle the engine for 3 seconds after warming up the engine (the engine coolant temperature is 70°C (158°F) or higher) and allowing 1 minute to elapse after starting the engine. No. 4 Exhaust gas temperature sensor output voltage is below 0.11 V for 3 seconds or more when all conditions are met. (1 trip detection logic):
·

After starting the engine, 1 minute or more elapses

·

Engine is running

·

Coolant temperature is 70°C (158°F) or higher


·

Open or short in No. 4 exhaust gas temperature sensor circuit

·

No. 4 exhaust gas temperature sensor

·

ECM



P2471
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Idle the engine for 3 seconds after warming up the engine (the engine coolant temperature is 70°C (158°F) or higher) and allowing 1 minute to elapse after starting the engine. No. 4 Exhaust gas temperature sensor output voltage is higher than 4.89 V for 3 seconds or more when all conditions are met. (1 trip detection logic):
·

After starting the engine, 1 minute or more elapses

·

Engine is running

·

Coolant temperature is 70°C (158°F) or higher


·

Open or short in No. 4 exhaust gas temperature sensor circuit

·

No. 4 exhaust gas temperature sensor

·

ECM



Related Data List
DTC No. Data List
P2470
P2471
·

Exhaust Temperature B1S4

·

SCR Temperature



MONITOR DESCRIPTION

The ECM constantly monitors the output voltages from the No. 4 exhaust gas temperature sensors in order to detect problems with the sensors. When the sensor output voltage deviates from the normal operating range (between 0.11 V and 4.89 V) for more than 3 seconds after the engine is warmed up, the ECM interprets this as malfunction of the sensor circuit and illuminates the MIL.

WIRING DIAGRAM

A356866E04
2.302,1.365 2.917,1.563 0.615,0.198 10 false THSO 3.125,1.365 3.385,1.625 0.26,0.26 10 false E2 2.115,1.573 2.271,1.771 0.156,0.198 10 false 2 3.417,1.552 3.573,1.75 0.156,0.198 10 false 1 1.917,1.813 2.229,2.01 0.313,0.198 10 false s7 1.927,1.99 4.469,2.396 2.542,0.406 10 false No. 4 Exhaust Gas Temperature Sensor 5.938,1.927 6.552,2.125 0.615,0.198 10 false G184 5.958,2.094 6.417,2.292 0.458,0.198 10 false ECM 5.552,0.583 6.167,0.781 0.615,0.198 10 false THSO 5.552,1.458 6.167,1.656 0.615,0.198 10 false ETSO 5.271,0.719 5.583,0.917 0.313,0.198 10 false 26 5.292,1.563 5.604,1.76 0.313,0.198 10 false 33

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT NO. 4 EXHAUST GAS TEMPERATURE SENSOR

OK

2.CHECK HARNESS AND CONNECTOR (NO. 4 EXHAUST GAS TEMPERATURE SENSOR - ECM)

NG

4.REPLACE NO. 4 EXHAUST GAS TEMPERATURE SENSOR
2.CHECK HARNESS AND CONNECTOR (NO. 4 EXHAUST GAS TEMPERATURE SENSOR - ECM)
a.

Disconnect the No. 4 exhaust gas temperature sensor.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
s7-2 (THSO) - G184-26 (THSO) Always Below 1 Ω
s7-1 (E2) - G184-33 (ETSO) Always Below 1 Ω
s7-2 (THSO) or G184-26 (THSO) - Body ground and other terminals Always 10 kΩ or higher
s7-1 (E2) or G184-33 (ETSO) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the No. 4 exhaust gas temperature sensor.


e.

Reconnect the ECM connector.



OK

3.REPLACE ECM

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.REPLACE ECM

NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.REPLACE NO. 4 EXHAUST GAS TEMPERATURE SENSOR

NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Start the engine.


d.

Idle the engine for 3 seconds or more after warming up the engine (the engine coolant temperature is 70°C (158°F) or higher) and allowing 1 minute to elapse after starting the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


f.

Confirm that the DTC is not output again.



NEXT

END