Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2018.06–2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P225D  NOx Sensor Performance - Signal Stuck Low Bank 1 Sensor 1  


DESCRIPTION

The ECM estimates the amount of NOx expelled while the engine is operating and compares the estimated integrated value of change for the NOx value and the integrated value of the No. 1 nitrogen oxides sensor based on actual output values.

When the actual integrated change value of the No. 1 nitrogen oxides sensor output does not significantly change but the NOx integrated value for the estimated amount of change reaches the specified value, the system judges that the No. 1 nitrogen oxides sensor is stuck and outputs a DTC.

P225D
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
After warming up the engine, alternate between idling and racing the engine under no load approximately 30 times. When the actual integrated change value of the No. 1 nitrogen oxides sensor output does not significantly change but the NOx integrated value for the estimated amount of change reaches the specified value
(2 trip detection logic)
No. 1 nitrogen oxides sensor

Related Data List
DTC No. Data List
P225D
·

NOx Corrected Density B1S1

·

Fr-NOx Sensor Active Status



CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P225D)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Result:
Result Proceed to
DTC P225D is output A
DTC P225D and other DTCs are output* B


HINT:

*: If any other DTCs (CAN communication malfunctions or open/short circuits) are output, perform troubleshooting for those DTCs first.




A

2.READ VALUE USING GTS (FR-NOX SENSOR ACTIVE STATUS AND NOX CORRECRED DENSITY B1S1)

B

2.READ VALUE USING GTS (FR-NOX SENSOR ACTIVE STATUS AND NOX CORRECRED DENSITY B1S1)
a.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.


b.

Connect the GTS to the DLC3.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Fr-NOx Sensor Active Status and NOx Corrected Density B1S1.


e.

Check that the No. 1 nitrogen oxides sensor is activated.

HINT:

If the Fr-NOx Sensor Active Status is ON, the No. 1 nitrogen oxides sensor is active.



f.

Alternate between idling and racing the engine under no load and check that the NOx Corrected Density B1S1 value changes.

OK:

The NOx Corrected Density B1S1 value changes. (Increases when engine is raced under no load, decreases when idling)


HINT:
·

Normal output is approximately 100 ppm at the maximum possible engine speed under no load.

·

It is easier to check the amount of NOx Corrected Density B1S1 change by displaying a graph on the GTS.




Result:
Proceed to
OK
NG



OK

3.INSPECT NO. 1 NITROGEN OXIDES SENSOR

NG

REPLACE NO. 1 NITROGEN OXIDES SENSOR

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>NITROGEN OXIDES SENSOR>REMOVAL

HINT:

Perform "A/F Sensor Compensation Reset" after replacing the No. 1 nitrogen oxides sensor.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION



3.INSPECT NO. 1 NITROGEN OXIDES SENSOR
a.

Check for open or short circuits, or damage to the sensor control unit of the No. 1 nitrogen oxides sensor and the detection component wire harness.

OK:

No open or short circuit malfunction.



Result:
Proceed to
OK
NG



OK

4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

REPLACE NO. 1 NITROGEN OXIDES SENSOR

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>NITROGEN OXIDES SENSOR>REMOVAL

HINT:

Perform "A/F Sensor Compensation Reset" after replacing the No. 1 nitrogen oxides sensor.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION



4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.


c.

Turn the engine switch off for 30 seconds or more.


d.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.


e.

Alternate between idling and racing the engine under no load approximately 30 times.


f.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.


ii.

Input DTC P225D.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, alternate between idling and racing the engine under no load approximately 30 minutes again.



Result:
Proceed to
NEXT



NEXT

END