Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) › from 2019.08
RM27T0E _58 Vehicle Interior _053739 HEATING / AIR CONDITIONING _0261169 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  B1412/12  Ambient Temperature Sensor Circuit  


DESCRIPTION

The cooler thermistor (ambient temperature sensor) is installed in the front part of the cooler condenser assembly to detect the ambient temperature and control the air conditioning auto mode. The sensor connected to the air conditioning amplifier assembly detects fluctuations in the ambient temperature. This data is used for controlling the room temperature. The sensor sends a signal to the air conditioning amplifier assembly. The resistance of the cooler thermistor (ambient temperature sensor) changes in accordance with the cooler thermistor temperature (ambient temperature). As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.

The air conditioning amplifier assembly applies a voltage (5 V) to the cooler thermistor (ambient temperature sensor) and reads voltage changes as changes in the resistance of the cooler thermistor (ambient temperature sensor).

DTC Code DTC Detection Condition Trouble Area
B1412/12 An open or short in the cooler thermistor (ambient temperature sensor) circuit.
·

Cooler thermistor (ambient temperature sensor)

·

Harness or connector

·

Air conditioning amplifier assembly



WIRING DIAGRAM

E193111E36
1.302,1.208 2.073,1.469 0.771,0.26 10 false A124 4.656,3.323 6.906,3.531 2.25,0.208 10 false Air Conditioning Amplifier Assembly 1.375,0.688 1.5,0.854 0.125,0.167 10 false 1 2.667,0.688 2.792,0.854 0.125,0.167 10 false 2 5.156,0.688 5.281,0.854 0.125,0.167 10 false 5 5.094,2.646 5.292,2.813 0.198,0.167 10 false 13 5.375,0.781 5.771,0.948 0.396,0.167 10 false TAM 5.375,2.75 5.781,2.917 0.406,0.167 10 false SG-2 1.302,1.365 4.427,1.563 3.125,0.198 10 false Cooler Thermistor (Ambient Temperature Sensor) 4.667,3.167 4.958,3.333 0.292,0.167 10 false G25

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (AMBIENT TEMPERATURE SENSOR)
a.

Use the Data List to check if the cooler thermistor (ambient temperature sensor) is functioning properly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>DATA LIST / ACTIVE TEST

Air Conditioner
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Ambient Temp Sensor Cooler thermistor (ambient temperature sensor) /
Min: -23.3°C (-9.94°F)
Max: 65.95°C (150.71°F)
Actual ambient temperature displayed Open in the circuit: -23.3°C (-9.94°F).
Short in the circuit: 65.95°C (150.71°F).

OK:

The display is as specified in the normal condition column.



Result
Result Proceed to
OK (When troubleshooting according to problem symptoms table) A
OK (When troubleshooting according to the DTC) B
NG C


A

B

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

C

2.INSPECT COOLER THERMISTOR (AMBIENT TEMPERATURE SENSOR)
2.INSPECT COOLER THERMISTOR (AMBIENT TEMPERATURE SENSOR)
a.

Remove the cooler thermistor (ambient temperature sensor).

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AMBIENT TEMPERATURE SENSOR>REMOVAL


b.
E426412C01
2.885,0.406 2.885,0.208 2.885,0.208 3.021,0.208 true 0.479,0.219 0.792,0.375 0.313,0.156 10 false *a 3.073,0.125 3.333,0.313 0.26,0.188 10 false *b 0.052,2.802 0.365,2.958 0.313,0.156 10 false *c 1.781,4.406 2.094,4.563 0.313,0.156 10 false *d 0.406,4.188 1.021,4.385 0.615,0.198 10 false (50) 0.938,4.198 1.552,4.396 0.615,0.198 10 false (68) 1.469,4.198 2.083,4.396 0.615,0.198 10 false (86) 1.958,4.198 2.573,4.396 0.615,0.198 10 false (104) 2.51,4.198 2.917,4.406 0.406,0.208 10 false (122) 3.042,4.198 3.427,4.406 0.385,0.208 10 false (140)
*a Component without harness connected
(Cooler Thermistor (Ambient Temperature Sensor))
*b Sensor Area
*c Resistance (kΩ)
*d Temperature (°C (°F))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 10°C (50°F) 3.00 to 3.73 kΩ
15°C (59°F) 2.45 to 2.88 kΩ
20°C (68°F) 1.95 to 2.30 kΩ
25°C (77°F) 1.60 to 1.80 kΩ
30°C (86°F) 1.28 to 1.47 kΩ
35°C (95°F) 1.00 to 1.22 kΩ
40°C (104°F) 0.80 to 1.00 kΩ
45°C (113°F) 0.65 to 0.85 kΩ
50°C (122°F) 0.50 to 0.70 kΩ
55°C (131°F) 0.44 to 0.60 kΩ
60°C (140°F) 0.36 to 0.50 kΩ


NOTICE:
·

Even slightly touching the sensor may change the resistance value. Be sure to hold the connector of the sensor.

·

When measuring, the sensor temperature must be the same as the ambient temperature.



HINT:

As the temperature increases, the resistance decreases (refer to the graph).




OK

3.CHECK HARNESS AND CONNECTOR (AMBIENT TEMPERATURE SENSOR - AIR CONDITIONING AMPLIFIER)

NG

REPLACE COOLER THERMISTOR (AMBIENT TEMPERATURE SENSOR)

3.CHECK HARNESS AND CONNECTOR (AMBIENT TEMPERATURE SENSOR - AIR CONDITIONING AMPLIFIER)
a.

Disconnect the A124 sensor connector.


b.

Disconnect the G25 amplifier connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A124-2 - G25-5 (TAM) Always Below 1 Ω
A124-1 - G25-13 (SG-2)
G25-5 (TAM) - Body ground Always 10 kΩ or higher
G25-13 (SG-2) - Body ground




OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR