Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2018.06
RM27T0E _51 Engine / Hybrid System _053656 2TR-FE ENGINE CONTROL _0260420 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P0351  Ignition Coil "A" Primary / Secondary Circuit  P0352  Ignition Coil "B" Primary / Secondary Circuit  P0353  Ignition Coil "C" Primary / Secondary Circuit  P0354  Ignition Coil "D" Primary / Secondary Circuit  


DESCRIPTION

A Direct Ignition System (DIS) is used on this vehicle.

The DIS is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil and one spark plug is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring, is applied directly to each spark plug. The sparks of the spark plugs pass from the center electrode to the ground electrodes.

The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches on and off the current to the primary coil. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF) signal to the ECM for each cylinder ignition.

A255924E06
4.427,1.385 4.375,0.938 4.375,0.938 4.302,0.938 false 5.333,1.156 5.563,0.719 5.563,0.719 5.635,0.719 false 3.896,0.844 4.5,1 0.604,0.156 10 Igniter 4.51,0.479 5.323,0.656 0.813,0.177 10 from Battery 5.688,0.646 7.073,1.198 1.385,0.552 10 Ignition Coil Assembly (No. 1 Cylinder) 5.615,1.854 6.729,2.031 1.115,0.177 10 No. 1 Spark Plug 5.615,3.063 6.729,3.24 1.115,0.177 10 No. 2 Spark Plug 5.615,4.385 6.729,4.563 1.115,0.177 10 No. 3 Spark Plug 5.615,5.688 6.729,5.865 1.115,0.177 10 No. 4 Spark Plug 2.74,5.927 3.083,6.104 0.344,0.177 10 ECM 2.896,1.448 3.26,1.604 0.365,0.156 10 IGT1 2.885,1.75 3.26,1.896 0.375,0.146 10 IGF1 0.302,1.5 2.031,1.667 1.729,0.167 10 Crankshaft Position Sensor 0.313,3.292 2.042,3.458 1.729,0.167 10 Camshaft Position Sensor 2.885,2.76 3.25,2.917 0.365,0.156 10 IGT2 2.896,5.406 3.26,5.563 0.365,0.156 10 IGT4 2.875,4.094 3.24,4.25 0.365,0.156 10 IGT3 0.188,4.49 2.146,5.313 1.958,0.823 10 Other Sensors (Engine Coolant Temperature Sensor, Mass Air Flow Meter Sub-assembly, Throttle Position Sensor, etc.) 3.75,3.354 6.208,3.583 2.458,0.229 10 Ignition Coil Assembly (No. 2 Cylinder) 3.74,5.958 6.531,6.188 2.792,0.229 10 Ignition Coil Assembly (No. 4 Cylinder) 3.74,4.656 6.427,4.885 2.688,0.229 10 Ignition Coil Assembly (No. 3 Cylinder)

DTC No. DTC Detection Condition Trouble Area
P0351
P0352
P0353
P0354
No IGF signal is sent to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT (1 to 4) circuit between ignition coil and ECM

·

No. 1 to No. 4 ignition coil assembly

·

ECM



Reference: Inspection using an oscilloscope.

U147435E02
0.521,0.208 1.021,0.417 0.5,0.208 10 false 2 V/DIV 1,0.615 1.094,0.823 0.094,0.208 10 false 1 1,1.208 1.094,1.417 0.094,0.208 10 false 2 0.625,0.906 0.958,1.115 0.333,0.208 10 false GND 0.625,1.49 0.958,1.698 0.333,0.208 10 false GND 1.771,1.865 2.635,2.073 0.865,0.208 10 false 20 msec./DIV

Items Contents
Terminals 1. IGT1, IGT2, IGT3, IGT4 - E1
2. IGF1 - E1
Equipment Settings 2 V/DIV, 20 msec./DIV
Conditions Idling

HINT:

While cranking or idling the engine, check the waveform between terminals IGT (1 to 4) and E1, and IGF1 and E1 of the ECM connector.



MONITOR DESCRIPTION

A212405E08
1.782,1.645 2.181,1.818 0.399,0.173 10 ECM 2.956,1.3 3.225,1.485 0.269,0.185 10 IGT 2.949,1.726 3.226,1.886 0.278,0.160 10 IGF 4.153,1.509 4.594,1.655 0.441,0.145 10 Igniter 5.4,1.348 6.167,1.521 0.767,0.173 10 Ignition Coil 4.465,2.35 6.163,2.540 1.698,0.191 10 Ignition Coil Assembly 0.213,3.113 1.146,3.443 0.934,0.330 10 Ignition Signal (IGT) 1.642,3.541 2.131,3.731 0.489,0.191 10 Normal 1.383,3.947 2.150,4.138 0.767,0.191 10 Malfunction 0.262,3.907 1.146,4.768 0.884,0.862 10 Ignition Confirmation Signal (IGF) 3.631,4.507 4.482,4.684 0.850,0.177 10 Circuit Open 5.95,4.97 6.314,5.167 0.364,0.198 10 Time

If the ECM does not receive any IGF signals despite transmitting the IGT signal, it interprets this as a fault in the igniter and stores a DTC.

If the malfunction is not repaired successfully, a DTC is stored 1 second after the engine is next started.

MONITOR STRATEGY

Required Sensors/Components (Main) Igniter
Required Sensors/Components (Related) ECM
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine.

7.

Idle the engine for 20 seconds or more.

8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0351, P0352, P0353 or P0354.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A355928E05
6.167,0.531 6.594,0.75 0.427,0.219 10 false MREL 5.729,0.542 6.135,0.74 0.406,0.198 10 false G181 5.938,0.365 6.104,0.563 0.167,0.198 10 false 6 6.146,1.083 6.604,1.323 0.458,0.24 10 false IGT1 5.729,1.083 6.083,1.271 0.354,0.188 10 false C153 5.906,0.896 6.115,1.094 0.208,0.198 10 false 16 6.167,2.833 6.625,3.031 0.458,0.198 10 false IGT2 5.74,2.854 6.115,3.052 0.375,0.198 10 false C153 5.896,2.656 6.125,2.844 0.229,0.188 10 false 15 5.729,4.615 6.135,4.823 0.406,0.208 10 false C153 5.896,4.417 6.104,4.594 0.208,0.177 10 false 14 5.729,6.365 6.125,6.583 0.396,0.219 10 false C153 5.74,6.948 6.135,7.146 0.396,0.198 10 false C153 5.729,7.479 6.146,7.708 0.417,0.229 10 false C153 5.885,6.146 6.115,6.313 0.229,0.167 10 false 13 5.896,6.74 6.115,6.917 0.219,0.177 10 false 12 5.948,7.292 6.146,7.469 0.198,0.177 10 false 3 6.167,4.594 6.563,4.792 0.396,0.198 10 false IGT3 6.177,6.344 6.594,6.531 0.417,0.188 10 false IGT4 6.156,6.938 6.615,7.167 0.458,0.229 10 false IGF1 6.188,7.469 6.458,7.635 0.271,0.167 10 false E1 2.594,7.469 4.5,7.75 1.906,0.281 10 false No. 4 Ignition Coil Assembly 2.583,7.302 4.094,7.5 1.51,0.198 10 false C187 2.625,5.688 4.438,6 1.813,0.313 10 false No. 3 Ignition Coil Assembly 2.615,5.521 3.75,5.698 1.135,0.177 10 false C186 2.604,3.927 4.646,4.167 2.042,0.24 10 false No. 2 Ignition Coil Assembly 2.604,3.76 3.635,3.958 1.031,0.198 10 false C185 2.594,2.167 4.573,2.448 1.979,0.281 10 false No. 1 Ignition Coil Assembly 2.604,2 3.667,2.188 1.063,0.188 10 false C184 2.698,1.083 2.979,1.26 0.281,0.177 10 false +B 3.979,1.094 4.385,1.292 0.406,0.198 10 false IGT1 2.698,1.667 3.073,1.875 0.375,0.208 10 false GND 4.052,1.656 4.49,1.865 0.438,0.208 10 false IGF 4.406,0.979 4.646,1.219 0.24,0.24 10 false 3 4.427,1.583 4.625,1.771 0.198,0.188 10 false 2 2.49,0.99 2.729,1.281 0.24,0.292 10 false 1 2.49,1.573 2.75,1.823 0.26,0.25 10 false 4 3.99,2.854 4.458,3.083 0.469,0.229 10 false IGT2 4.052,3.438 4.49,3.646 0.438,0.208 10 false IGF 2.698,3.438 3.073,3.646 0.375,0.208 10 false GND 2.698,2.854 3.083,3.052 0.385,0.198 10 false +B 2.5,2.74 2.698,2.938 0.198,0.198 10 false 1 4.417,3.344 4.604,3.563 0.188,0.219 10 false 2 4.396,2.75 4.563,2.938 0.167,0.188 10 false 3 2.49,3.323 2.75,3.573 0.26,0.25 10 false 4 3.969,4.615 4.354,4.771 0.385,0.156 10 false IGT3 4.052,5.188 4.49,5.396 0.438,0.208 10 false IGF 2.698,5.198 3.073,5.406 0.375,0.208 10 false GND 2.708,4.594 2.979,4.771 0.271,0.177 10 false +B 2.469,4.479 2.677,4.688 0.208,0.208 10 false 1 4.385,4.49 4.552,4.698 0.167,0.208 10 false 3 2.479,5.104 2.635,5.292 0.156,0.188 10 false 4 4.406,5.094 4.583,5.323 0.177,0.229 10 false 2 2.729,6.354 3,6.531 0.271,0.177 10 false +B 3.958,6.385 4.344,6.542 0.385,0.156 10 false IGT4 4.052,6.948 4.49,7.156 0.438,0.208 10 false IGF 2.698,6.948 3.073,7.156 0.375,0.208 10 false GND 4.427,6.25 4.604,6.469 0.177,0.219 10 false 3 4.417,6.854 4.594,7.083 0.177,0.229 10 false 2 2.469,6.229 2.677,6.438 0.208,0.208 10 false 1 2.5,6.823 2.656,7.01 0.156,0.188 10 false 4 0.615,7.167 2.177,7.438 1.563,0.271 10 false Noise Filter (Ignition) 0.615,7.01 1.24,7.26 0.625,0.25 10 false C68 6.354,8.01 6.74,8.25 0.385,0.24 10 false ECM 0.104,0.552 0.281,0.76 0.177,0.208 10 false A 0.094,1.115 0.271,1.292 0.177,0.177 10 false B

A413223E01
4.333,0.573 5.708,0.771 1.375,0.198 10 false EFI NO. 2 3.292,0.427 3.604,0.625 0.313,0.198 10 false 1W 3.354,0.219 3.667,0.417 0.313,0.198 10 false 10 3.292,0.875 3.604,1.073 0.313,0.198 10 false 1W 3.385,0.656 3.542,0.854 0.156,0.198 10 false 8 2.115,1.229 4.26,1.427 2.146,0.198 10 false EFI MAIN NO. 1 0.625,0.594 2.771,0.792 2.146,0.198 10 false EFI MAIN NO. 1 2.229,2.938 5.594,3.135 3.365,0.198 10 false No.1 Integration Relay 1.823,2.708 2.135,2.906 0.313,0.198 10 false 1W 0.458,2.708 0.771,2.906 0.313,0.198 10 false 1S 0.76,2.698 0.917,2.896 0.156,0.198 10 false 1 2.146,2.698 2.302,2.896 0.156,0.198 10 false 4 0.646,4.333 1.563,4.531 0.917,0.198 10 false 70A FL 2.01,5.458 3.083,5.656 1.073,0.198 10 false 250A FL 3.531,5.479 4.906,5.677 1.375,0.198 10 false INJ NO. 2 0.802,5.813 1.875,6.01 1.073,0.198 10 false Battery 5.958,3.635 6.635,3.854 0.677,0.219 10 false INJ NO. 2 4.969,3.167 5.125,3.365 0.156,0.198 10 false 2 5.708,3.167 5.865,3.365 0.156,0.198 10 false 3 4.979,4.135 5.135,4.333 0.156,0.198 10 false 1 5.708,4.146 5.865,4.344 0.156,0.198 10 false 5 6.802,0.865 6.958,1.063 0.156,0.198 10 false A 6.792,1.719 6.948,1.917 0.156,0.198 10 false B

CAUTION / NOTICE / HINT

HINT:
·

These DTCs indicate malfunctions relating to the primary circuit.

·

If DTC P0351 is stored, check the No. 1 ignition coil circuit.

·

If DTC P0352 is stored, check the No. 2 ignition coil circuit.

·

If DTC P0353 is stored, check the No. 3 ignition coil circuit.

·

If DTC P0354 is stored, check the No. 4 ignition coil circuit.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result
Result Proceed to
DTC P0351, P0352, P0353 or P0354 is output A
DTC P0351, P0352, P0353 and P0354 are output B



A

2.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353 OR P0354)

B

6.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)
2.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353 OR P0354)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Shuffle the arrangement of the ignition coil assemblies (among the No. 1 to No. 4 cylinders).

NOTICE:

Do not shuffle the connectors.



f.

Perform a simulation test.


g.

Check the DTCs output to the GTS.

Result
Result Proceed to
Same DTC output A
Different ignition coil assembly DTC output B

HINT:

Perform "Inspection After Repair" after replacing the ignition coil (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).




A

3.CHECK IGNITION COIL ASSEMBLY (POWER SOURCE)

B

REPLACE IGNITION COIL ASSEMBLY

3.CHECK IGNITION COIL ASSEMBLY (POWER SOURCE)
a.
A451271C04
0.229,0.385 0.563,0.646 0.333,0.26 0.229,0.729 0.563,0.99 0.333,0.26 0.219,1.438 0.552,1.698 0.333,0.26 0.219,1.073 0.552,1.333 0.333,0.26 0.198,1.802 0.573,2.073 0.375,0.271 0.198,2.177 0.573,2.448 0.375,0.271 0.198,2.542 0.573,2.813 0.375,0.271 0.208,2.896 0.583,3.167 0.375,0.271 1.188,2.979 1.302,2.5 false 2.406,2.938 2.156,2.51 false 0.323,0.115 0.813,0.563 0.49,0.448 10 false *a 0.271,0.792 0.792,1.167 0.521,0.375 10 false C8 0.26,0.438 0.781,0.75 0.521,0.313 10 false C7 0.26,1.135 0.719,1.521 0.458,0.385 10 false C9 0.271,1.5 0.646,1.74 0.375,0.24 10 false C10 1.104,3.021 1.469,3.24 0.365,0.219 10 false +B 2.271,2.979 2.635,3.198 0.365,0.219 10 false GND 0.24,1.865 0.854,2.063 0.615,0.198 10 false C184 0.24,2.25 0.854,2.448 0.615,0.198 10 false C185 0.229,2.604 0.844,2.802 0.615,0.198 10 false C186 0.24,2.969 0.854,3.167 0.615,0.198 10 false C187 0.615,0.458 0.927,0.656 0.313,0.198 10 false *A 0.635,0.823 0.948,1.021 0.313,0.198 10 false *A 0.635,1.125 0.948,1.323 0.313,0.198 10 false *A 0.635,1.49 0.948,1.688 0.313,0.198 10 false *A 0.667,1.885 0.979,2.083 0.313,0.198 10 false *B 0.656,2.26 0.969,2.458 0.313,0.198 10 false *B 0.646,2.625 0.958,2.823 0.313,0.198 10 false *B 0.646,2.99 0.958,3.188 0.313,0.198 10 false *B
*A -2018/12
*B 2019/1-
*a Front view of wire harness connector
(to Ignition Coil Assembly)


Disconnect the ignition coil assembly connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
(-2018/12)
Tester Connection Switch Condition Specified Condition
C7-1 (+B) - C7-4 (GND) Ignition switch ON 11 to 14 V
C8-1 (+B) - C8-4 (GND) Ignition switch ON 11 to 14 V
C9-1 (+B) - C9-4 (GND) Ignition switch ON 11 to 14 V
C10-1 (+B) - C10-4 (GND) Ignition switch ON 11 to 14 V

(2019/1-)
Tester Connection Switch Condition Specified Condition
C184-1 (+B) - C184-4 (GND) Ignition switch ON 11 to 14 V
C185-1 (+B) - C185-4 (GND) Ignition switch ON 11 to 14 V
C186-1 (+B) - C186-4 (GND) Ignition switch ON 11 to 14 V
C187-1 (+B) - C187-4 (GND) Ignition switch ON 11 to 14 V




OK

4.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)

NG

6.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)
4.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
a.

Disconnect the ignition coil assembly connectors.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
(-2018/12)
Tester Connection Condition Specified Condition
C7-2 (IGF) - C153-12 (IGF1) Always Below 1 Ω
C8-2 (IGF) - C153-12 (IGF1) Always Below 1 Ω
C9-2 (IGF) - C153-12 (IGF1) Always Below 1 Ω
C10-2 (IGF) - C153-12 (IGF1) Always Below 1 Ω
C7-2 (IGF) or C153-12 (IGF1) - Body ground Always 10 kΩ or higher
C8-2 (IGF) or C153-12 (IGF1) - Body ground Always 10 kΩ or higher
C9-2 (IGF) or C153-12 (IGF1) - Body ground Always 10 kΩ or higher
C10-2 (IGF) or C153-12 (IGF1) - Body ground Always 10 kΩ or higher

(2019/1-)
Tester Connection Condition Specified Condition
C184-2 (IGF) - C153-12 (IGF1) Always Below 1 Ω
C185-2 (IGF) - C153-12 (IGF1) Always Below 1 Ω
C186-2 (IGF) - C153-12 (IGF1) Always Below 1 Ω
C187-2 (IGF) - C153-12 (IGF1) Always Below 1 Ω
C184-2 (IGF) or C153-12 (IGF1) - Body ground Always 10 kΩ or higher
C185-2 (IGF) or C153-12 (IGF1) - Body ground Always 10 kΩ or higher
C186-2 (IGF) or C153-12 (IGF1) - Body ground Always 10 kΩ or higher
C187-2 (IGF) or C153-12 (IGF1) - Body ground Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION COIL ASSEMBLY - ECM)

5.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
a.

Disconnect the ignition coil assembly connectors.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
(-2018/12)
Tester Connection Condition Specified Condition
C7-3 (IGT1) - C153-16 (IGT1) Always Below 1 Ω
C8-3 (IGT2) - C153-15 (IGT2) Always Below 1 Ω
C9-3 (IGT3) - C153-14 (IGT3) Always Below 1 Ω
C10-3 (IGT4) - C153-13 (IGT4) Always Below 1 Ω
C7-3 (IGT1) or C153-16 (IGT1) - Body ground Always 10 kΩ or higher
C8-3 (IGT2) or C153-15 (IGT2) - Body ground Always 10 kΩ or higher
C9-3 (IGT3) or C153-14 (IGT3) - Body ground Always 10 kΩ or higher
C10-3 (IGT4) or C153-13 (IGT4) - Body ground Always 10 kΩ or higher

(2019/1-)
Tester Connection Condition Specified Condition
C184-3 (IGT1) - C153-16 (IGT1) Always Below 1 Ω
C185-3 (IGT2) - C153-15 (IGT2) Always Below 1 Ω
C186-3 (IGT3) - C153-14 (IGT3) Always Below 1 Ω
C187-3 (IGT4) - C153-13 (IGT4) Always Below 1 Ω
C184-3 (IGT1) or C153-16 (IGT1) - Body ground Always 10 kΩ or higher
C185-3 (IGT2) or C153-15 (IGT2) - Body ground Always 10 kΩ or higher
C186-3 (IGT3) or C153-14 (IGT3) - Body ground Always 10 kΩ or higher
C187-3 (IGT4) or C153-13 (IGT4) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION COIL ASSEMBLY - ECM)

6.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)
a.

Disconnect the ignition coil assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
(-2018/12)
Tester Connection Condition Specified Condition
C7-4 (GND) - Body ground Always Below 1 Ω
C8-4 (GND) - Body ground Always Below 1 Ω
C9-4 (GND) - Body ground Always Below 1 Ω
C10-4 (GND) - Body ground Always Below 1 Ω

(2019/1-)
Tester Connection Condition Specified Condition
C184-4 (GND) - Body ground Always Below 1 Ω
C185-4 (GND) - Body ground Always Below 1 Ω
C186-4 (GND) - Body ground Always Below 1 Ω
C187-4 (GND) - Body ground Always Below 1 Ω




OK

7.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - INJ NO.2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)

7.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - INJ NO.2 RELAY)
a.

Disconnect the ignition coil assembly connectors.


b.

Remove the INJ NO. 2 relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
(-2018/12)
Tester Connection Condition Specified Condition
C7-1 (+B) - INJ NO. 2 relay terminal 3 Always Below 1 Ω
C8-1 (+B) - INJ NO. 2 relay terminal 3 Always Below 1 Ω
C9-1 (+B) - INJ NO. 2 relay terminal 3 Always Below 1 Ω
C10-1 (+B) - INJ NO. 2 relay terminal 3 Always Below 1 Ω
C7-1 (+B) or INJ NO. 2 relay terminal 3 - Body ground Always 10 kΩ or higher
C8-1 (+B) or INJ NO. 2 relay terminal 3 - Body ground Always 10 kΩ or higher
C9-1 (+B) or INJ NO. 2 relay terminal 3 - Body ground Always 10 kΩ or higher
C10-1 (+B) or INJ NO. 2 relay terminal 3 - Body ground Always 10 kΩ or higher

(2019/1-)
Tester Connection Condition Specified Condition
C184-1 (+B) - INJ NO. 2 relay terminal 3 Always Below 1 Ω
C185-1 (+B) - INJ NO. 2 relay terminal 3 Always Below 1 Ω
C186-1 (+B) - INJ NO. 2 relay terminal 3 Always Below 1 Ω
C187-1 (+B) - INJ NO. 2 relay terminal 3 Always Below 1 Ω
C184-1 (+B) or INJ NO. 2 relay terminal 3 - Body ground Always 10 kΩ or higher
C185-1 (+B) or INJ NO. 2 relay terminal 3 - Body ground Always 10 kΩ or higher
C186-1 (+B) or INJ NO. 2 relay terminal 3 - Body ground Always 10 kΩ or higher
C187-1 (+B) or INJ NO. 2 relay terminal 3 - Body ground Always 10 kΩ or higher




OK

8.INSPECT INJ NO.2 RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT INJ NO.2 RELAY

OK

9.CHECK HARNESS AND CONNECTOR (INJ NO. 2 RELAY - BODY GROUND)

NG

REPLACE INJ NO.2 RELAY

9.CHECK HARNESS AND CONNECTOR (INJ NO. 2 RELAY - BODY GROUND)
a.

Remove the INJ NO. 2 relay from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
INJ No. 2 relay terminal 1 - Body ground Always Below 1 Ω




OK

10.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (INJ NO. 2 RELAY - BATTERY)

10.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - BODY GROUND)
a.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1W-4 - Body ground Always Below 1 Ω




OK

11.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY(EFI MAIN NO. 1) - INJ NO.2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY(EFI MAIN NO. 1) - INJ NO.2 RELAY)
a.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


b.

Remove the INJ NO. 2 relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1W-10 - INJ NO. 2 relay terminal 2 Always Below 1 Ω
1W-10 or INJ NO. 2 relay terminal 2 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR