Home › Engine / Hybrid System › CRUISE CONTROL › MILLIMETER WAVE RADAR SENSOR › from 2020.08
RM27T0E _51 Engine / Hybrid System _053696 CRUISE CONTROL _0260751 MILLIMETER WAVE RADAR SENSOR N

CRUISE CONTROL  MILLIMETER WAVE RADAR SENSOR  ADJUSTMENT  


PROCEDURE

Hide 1. PREPARATION FOR MILLIMETER WAVE RADAR SENSOR ASSEMBLY ADJUSTMENT

a.
E383804C13
0.219,1.25 0.531,1.406 0.313,0.156 10 false *a 1.427,2.385 1.74,2.542 0.313,0.156 10 false *b 2.208,0.208 2.438,0.375 0.229,0.167 10 true *d 0.229,3.625 0.458,3.802 0.229,0.177 10 false *e 1.396,3.646 1.625,3.875 0.229,0.229 10 true *g 1.188,0.198 1.5,0.396 0.313,0.198 10 false *c 2.26,3.01 2.573,3.208 0.313,0.198 10 false *f
*a 5 m (16.4 ft.)
*b 6 m (19.7 ft.)
*c 4 m (13.1 ft.)
*d 2 m (6.56 ft.)
*e 3 m (9.84 ft.)
*f 1.5 m (4.92 ft.)
*g 2.5 m (8.2 ft.)
V100144

Do not place any metal objects in this area
V100155

Do not place metal objects with a height of more than 50 mm (1.97 in.) in this area


Park the vehicle on a level surface where the area in front of the vehicle shown in the illustration is free of metal objects.

HINT:

Metal objects with a height of 50 mm (1.97 in.) or less placed within the area shown in the illustration will not affect the adjustment.



b.

Check the levelness of the ground.

i.
E383805C04
1.458,0.573 1.771,0.771 0.313,0.198 10 false *a
*a 3 m (9.84 ft.)
V100155

Levelness Check Point


Check the levelness of the ground at the 3 points shown in the illustration.


ii.

Place the level on each levelness check point and check that the air bubble of the level is centered.

E344401



c.

Adjust the tire inflation pressure to the specified pressure.

Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION


d.

Clean the radiator grille emblem or millimeter wave radar sensor assembly.


e.

Visually inspect the front of the vehicle.

HINT:

Confirm that there is no damage or deformation.



f.

Check that the radiator grille emblem and millimeter wave radar sensor assembly is clean and there is no dirt or snow covering them.


g.

Visually inspect the front bumper cover and radiator grille.

HINT:

Confirm that there is no damage or deformation.



Hide 2.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY VERTICALLY AND HORIZONTALLY

a.

Adjust SST (reflector) height.

i.
C320141C03
1.448,0.615 1.938,0.615 false 1.708,0.865 1.927,0.615 false 1.969,0.542 2.281,0.74 0.313,0.198 10 false *a
*a SST (reflector)


Adjust SST (reflector) so that the center of SST (reflector) is the same height as the millimeter wave radar sensor assembly.

HINT:

Make sure to align the center of SST (reflector) with the millimeter wave radar sensor assembly (the center of the emblem).


Reference Value:

939 mm (3.08 ft.)


SST
09870-60000  (09870-60010)
09870-60040  



b.

Place SST (reflector).

i.

w/o Tire Carrier:

Hang a weight with a pointed tip from the center of the symbol emblem, and mark the front center point of the vehicle (point A) on the ground.

B485932C01
2.917,2.354 3.344,2.208 false 2.917,2.458 3.333,2.542 false 4.948,1.146 5.531,0.885 true 4.958,2.292 5.427,2.448 false 5.479,2.406 5.792,2.563 0.313,0.156 10 false *a 3.396,2.125 3.708,2.281 0.313,0.156 10 false *b 5.583,0.781 5.896,0.938 0.313,0.156 10 false *c 4.677,2.063 4.99,2.219 0.313,0.156 10 false *d 3.417,2.5 3.573,2.698 0.156,0.198 10 false A 5.052,2.073 5.365,2.271 0.313,0.198 10 false *d
*a String *b Weight
*c Center *d Bilateral Symmetry



ii.

w/ Tire Carrier:

Hang a weight with a pointed tip from the center of the rear bumper cover, and mark the front center point of the vehicle (point A) on the ground.

B489621C01
2.948,2.365 3.417,2.229 false 2.927,2.448 3.396,2.469 false 5.479,1.906 5.885,2.063 false 5.958,2.031 6.271,2.188 0.313,0.156 10 false *a 3.469,2.146 3.781,2.313 0.313,0.167 10 false *b 4.948,1.76 5.26,1.917 0.313,0.156 10 false *c 5.781,1.771 6.094,1.969 0.313,0.198 10 false *c 3.479,2.396 3.635,2.594 0.156,0.198 10 false A
*a String *b Weight
*c Bilateral Symmetry - -


HINT:

Lightly flick the string with your fingers several times to confirm that the string is perpendicular to the ground.



iii.

Hang a weight with a pointed tip from the center of the radiator grille emblem, and mark the front center point of the vehicle (point B) on the ground.

B485933C01
2.021,2.177 2.469,2.313 false 2.021,1.042 2.594,0.823 true 4.042,2.333 3.5,2.177 false 4.063,2.458 3.479,2.563 false 2.542,2.26 2.854,2.417 0.313,0.156 10 false *a 3.313,2.063 3.625,2.219 0.313,0.156 10 false *b 2.667,0.719 2.979,0.875 0.313,0.156 10 false *c 1.74,1.948 2.052,2.104 0.313,0.156 10 false *d 2.125,1.969 2.438,2.167 0.313,0.198 10 false *d 3.333,2.479 3.49,2.677 0.156,0.198 10 false B
*a String *b Weight
*c Center *d Bilateral Symmetry


HINT:

Lightly flick the string with your fingers several times to confirm that the string is perpendicular to the ground.



iv.

Using tape and a string, create a line that connects point B to point A and extends at least 3000 mm (9.84 ft.) beyond the front center point of the vehicle.

B485942C01
0.323,1.74 0.323,2.104 false 0.719,1.646 0.719,2.25 false 6.771,2.125 6.771,1.74 false 0.667,2.302 0.979,2.458 0.313,0.156 10 false *a 0.26,2.135 0.573,2.292 0.313,0.156 10 false *b 2.042,0.302 2.354,0.458 0.313,0.156 10 false *c 1,1.406 1.219,1.625 0.219,0.219 10 false C 6.719,2.198 7.031,2.396 0.313,0.198 10 false *b 2.823,1.406 2.979,1.604 0.156,0.198 10 false B 6.531,1.417 6.688,1.615 0.156,0.198 10 false A
*a String *b Tape
*c 3000 mm (9.84 ft.) - -


HINT:
·

Make sure the string is taut when securing it with tape.

·

Lightly flick the string with your fingers several times to confirm that the string is aligned with point B.




v.

Mark point C (SST (reflector) placement position) at a position 3000 mm (9.84 ft.) from point B.


vi.

Place SST (reflector) at point C.



c.

Front Beam Axis Adjustment:

NOTICE:
·

Close all of the doors.

·

Ensure that nobody enters the adjustment area during the adjustment.

·

Do not move or shake the vehicle during adjustment (do not get in or out of the vehicle).

·

Do not turn off the GTS or ignition switch.

·

If the vehicle moves or is shaken during beam axis adjustment such as during strong winds or a door is opened or closed, perform the adjustment again.



i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch on (IG).


iii.

Turn the GTS on and turn the cruise control system on using the cruise control main switch (ON/OFF button).


iv.

Enter the following menus: Body Electrical / Front Radar Sensor / Utility / Front Beam Axis Adjustment.


v.

Press "Next".


vi.

Perform the adjustment according to the display on the GTS.

NOTICE:

If an error code is displayed, perform troubleshooting according to the following table, then perform the adjustment again.


Error No. Error Description Cause of Error Action to be Taken
1 No target abnormality
·

SST (reflector) is placed incorrectly.

·

The radiator grille emblem or millimeter wave radar sensor assembly is covered by dirt or snow.


Place SST (reflector) in the correct position. (See page 2. MILLIMETER WAVE RADAR SENSOR ASSEMBLY VERTICALLY AND HORIZONTALLY (b) Place SST (reflector))
Clean the radiator grille emblem or millimeter wave radar sensor assembly.
2 Target distance abnormality
·

SST (reflector) is placed incorrectly.


Place SST (reflector) in the correct position. (See page 2. MILLIMETER WAVE RADAR SENSOR ASSEMBLY VERTICALLY AND HORIZONTALLY (b) Place SST (reflector))
3 Plural targets abnormality
·

There is a reflective object near SST (reflector).

·

A person entered the adjustment area.


Remove any reflective objects.
Ensure that nobody enters the adjustment area during the adjustment. (See page 1. PREPARATION FOR MILLIMETER WAVE RADAR SENSOR ASSEMBLY ADJUSTMENT)
4 Target move abnormality
·

SST (reflector) was moved out of position or shaking during the adjustment due to wind.

·

A person entered the adjustment area.


Place SST (reflector) in the correct position. (See page 2. MILLIMETER WAVE RADAR SENSOR ASSEMBLY VERTICALLY AND HORIZONTALLY (b)Place SST (reflector))
Perform adjustment in an area with no wind.
Ensure that nobody enters the adjustment area during the adjustment. (See page 1. PREPARATION FOR MILLIMETER WAVE RADAR SENSOR ASSEMBLY ADJUSTMENT)
5 Axis adjustment
·

Optical axis adjustment has not been performed.


Optical axis adjustment. (See page 2. MILLIMETER WAVE RADAR SENSOR ASSEMBLY VERTICALLY AND HORIZONTALLY (c) Front Beam Axis Adjustment)
6 Target angle abnormality
·

SST (reflector) is placed incorrectly.

·

The beam axis of the millimeter wave radar sensor assembly is outside the automatic correction range.


Place SST (reflector) in the correct position. (See page 2. MILLIMETER WAVE RADAR SENSOR ASSEMBLY VERTICALLY AND HORIZONTALLY (b)Place SST (reflector))
Check the condition of the millimeter wave radar sensor assembly.
Check the condition of the radiator grille and front bumper assembly.
7 Radar abnormality
·

Operation of the millimeter wave radar sensor assembly is abnormal.


Replace the millimeter wave radar sensor assembly.
8 Radar dirtiness
·

There is dirt on the radiator grille (or front panel) emblem or millimeter wave radar sensor assembly.


Clean the radiator grille (or front panel) emblem or millimeter wave radar sensor assembly.
9 Temperature abnormality
·

The temperature around the millimeter wave radar sensor assembly is too high.


Wait until the temperature drops to the operable range (-30 to 50°C).
10 Voltage abnormality
·

IG power source voltage is outside the operable range of the millimeter wave radar sensor assembly.


Check the battery voltage (specified condition: 10 to 16 V).
·

for 1GR-FE:

(Click here)

·

for 1GD-FTV:

(Click here)

·

for 2TR-FE:

(Click here)


11 External communication abnormality
·

CAN communication between forward recognition camera and the millimeter wave radar sensor assembly is abnormal.


Check the condition of the connectors and wire harness.
12 Radar axis aiming failure upward
·

The beam axis of the millimeter wave radar sensor assembly is outside the automatic correction range (upward).

·

Road inclement is outside the standard value.


Check the condition of the millimeter wave radar sensor assembly.
Confirm road gradient.
13 Radar axis aiming failure downward
·

The beam axis of the millimeter wave radar sensor assembly is outside the automatic correction range (downward).

·

Road inclement is outside the standard value.


Check the condition of the millimeter wave radar sensor assembly.
Confirm road gradient.
14 Vehicle speed abnormality
·

The vehicle is not stationary.


Ensure that the vehicle remains stationary.
15 Other
·

A mode change error occurred.

·

Operation of the yaw rate sensor is abnormal.

·

The vehicle is shaking.


Check for DTCs.
(Click here)
Check for DTCs.
(Click here)
Ensure that the vehicle remains stationary.
16 Time out
·

The vehicle cannot communicate with GTS normally.

·

The vehicle does not keep still during beam axis adjustment.

·

Operation of the millimeter wave radar sensor assembly is abnormal.


·

Ensure that the vehicle is connected with the GTS correctly.

·

Ensure that the vehicle remains stationary.

·

Perform beam axis adjustment again and replace the millimeter wave radar sensor assembly if the same error code is output.


17 Target parameter abnormality
·

Wrong mode is selected.


Perform beam axis adjustment again.
18 Vehicle information undefined
·

CAN communication between forward recognition camera and the millimeter wave radar sensor assembly is abnormal.


Check the condition of the connectors.


vii.

Press the "Exit" to finish front beam axis adjustment.



d.

Front Beam Axis Misalignment Reading:

NOTICE:
·

Close all of the doors.

·

Ensure that nobody enters the adjustment area during the adjustment.

·

Do not move or shake the vehicle during adjustment (do not get in or out of the vehicle).

·

Do not turn off the GTS or ignition switch.

·

If the vehicle moves or is shaken during beam axis adjustment such as during strong winds or a door is opened or closed, perform the adjustment again.



i.

Enter the following menus: Body Electrical / Front Radar Sensor / Utility / Front Beam Axis Misalignment Reading.


ii.

Press "Next".


iii.

Perform the adjustment according to the display on the GTS.

Specified Condition:
Vertical -0.5 to 0.5 deg
Horizontal -0.6 to 0.6 deg


NOTICE:

If the result is not as specified, perform beam axis adjustment again.




e.

Front Radar Acceleration Sensor Calibration:

i.

Enter the following menus: Body Electrical / Front Radar Sensor / Utility / Front Radar Acceleration Sensor Calibration.


ii.

Turn the ignition switch off.


iii.

Disconnect the GTS from the DLC3.



f.

After beam axis adjustment completes, clear the following system vehicle control history entries.

i.

Clear vehicle control history (Dynamic radar cruise control system).

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>VEHICLE CONTROL HISTORY


ii.

Clear vehicle control history (Lane departure alert system).

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>VEHICLE CONTROL HISTORY


iii.

Clear vehicle control history (Front radar sensor system).

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT RADAR SENSOR SYSTEM>VEHICLE CONTROL HISTORY


iv.

Clear vehicle control history (Pre-collision system).

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>VEHICLE CONTROL HISTORY