Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts when making adjustments.
The specified torque for standard bolts is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).
1.INSPECT REAR DOOR
Check that the clearance measurements of areas A through N are within the standard range.
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 3.7 to 6.7 mm (0.146 to 0.264 in.) | B | 4.2 to 7.2 mm (0.165 to 0.284 in.) |
| C | 3.6 to 6.6 mm (0.142 to 0.260 in.) | D | 4.9 to 7.9 mm (0.193 to 0.311 in.) |
| E | 2.7 to 5.7 mm (0.106 to 0.224 in.) | F | -1.5 to 1.5 mm (-0.0591 to 0.0591 in.) |
| G | 4.05 to 7.05 mm (0.159 to 0.278 in.) | H | 4.45 to 7.45 mm (0.1752 to 0.2933 in.) |
| I | 4.05 to 7.05 mm (0.159 to 0.278 in.) | J | 4.45 to 7.45 mm (0.1752 to 0.2933 in.) |
| K | 3.0 to 6.0 mm (0.118 to 0.236 in.) | L | -1.5 to 1.5 mm (-0.0591 to 0.0591 in.) |
| M | 2.5 to 6.5 mm (0.0984 to 0.256 in.) | N | -2.0 to 2.0 mm (-0.0787 to 0.0787 in.) |
2. PRECAUTION
Be sure to read Precaution thoroughly before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
4.ADJUST REAR DOOR
Using SST, loosen the hinge bolts on the vehicle body and adjust the door position.
Tighten the hinge bolts on the vehicle body.
Loosen the hinge bolts on the door and adjust the door position.
Tighten the hinge bolts on the door.
Using a T40 "TORX" socket wrench, slightly loosen the striker mounting screws.
Using a brass bar and hammer, hit the striker to adjust its position.
Using a T40 "TORX" socket wrench, tighten the striker mounting screws.
5.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
6. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
7.INSPECT SRS WARNING LIGHT
Check the SRS warning light (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).