1. BEARING POSITION
| Mark | Front Race Diameter
Inside / Outside (mm (in.)) |
Thrust Bearing Diameter
Inside / Outside (mm (in.)) |
Rear Race Diameter
Inside / Outside (mm (in.)) |
|---|---|---|---|
| A | 74.2 (2.921) / 87.74 (3.454) | 71.9 (2.831) / 85.6 (3.370) | - |
| B | 40.0 (1.575) / 52.8 (2.079) | 34.6 (1.362) / 52.0 (2.047) | - |
| C | 22.0 (0.866) / 44.8 (1.764) | 21.3 (0.839) / 41.1 (1.618) | - |
| D | 38.4 (1.512) / 56.5 (2.224) | 33.3 (1.311) / 56.6 (2.228) | - |
| E | - | 40.83 (1.607) / 52.8 (2.079) | 39.6 (1.559) / 52.8 (2.079) |
| F | - | 37.1 (1.461) / 61.2 (2.409) | 44.0 (1.732) / 62.8 (2.472) |
| G | 65.8 (2.591) / 86.3 (3.398) | 63.3 (2.492) / 78.8 (3.102) | - |
| H | 66.3 (2.610) / 78.9 (3.106) | 63.3 (2.492) / 78.8 (3.102) | - |
| I | - | 55.7 (2.193) / 76.4 (3.008) | 53.7 (2.114) / 74.0 (2.913) |
| J | 33.4 (1.315) / 49.0 (1.929) | 32.1 (1.264) / 49.35 (1.943) | 32.1 (1.264) / 49.0 (1.929) |
| K | - | 21.0 (0.827) / 41.5 (1.634) | 23.13 (0.911) / 41.5 (1.634) |
| L | - | 43.55 (1.715) / 61.0 (2.402) | 47.1 (1.854) / 67.1 (2.642) |
35639B
2.INSTALL BRAKE PLATE STOPPER SPRING
Install the 2 brake plate stopper springs to the automatic transmission case sub-assembly.
The shapes of the parts are different. Refer to the illustration when installing the parts.
35629A
3.INSTALL NO. 4 BRAKE PISTON
Coat 2 new O-rings with ATF, and install them to the brake reaction sleeve.
Coat 2 new O-rings with ATF, and install them to the No. 4 brake piston.
Install the No. 4 brake piston to the brake reaction sleeve.
| *1 | No. 4 Brake Piston |
| *2 | Brake Reaction Sleeve |
Be careful not to damage the O-rings.
35626
4.INSTALL BRAKE REACTION SLEEVE
With the No. 4 brake piston underneath (the rear side), install the brake reaction sleeve and No. 4 brake piston to the automatic transmission case sub-assembly.
| *1 | Brake Reaction Sleeve |
| *2 | No. 4 Brake Piston |
Be careful not to damage the O-rings.
35623H
5.INSTALL 1ST AND REVERSE BRAKE PISTON
Coat a new O-ring with ATF, and install it to the 1st and reverse brake piston.
Install the 1st and reverse brake piston to the automatic transmission case sub-assembly while making sure that the protrusion of the 1st and reverse brake piston is positioned as shown in the illustration.
Be careful not to damage the O-ring.
Install the 1st and reverse brake return spring sub-assembly to the automatic transmission case sub-assembly.
Place the 1st and reverse brake return spring sub-assembly onto the 1st and reverse brake piston.
Place SST on the 1st and reverse brake return spring sub-assembly, and compress the 1st and reverse brake return spring sub-assembly.
| *a | Protective Tape |
Using a screwdriver, install the snap ring to the automatic transmission case sub-assembly.
Be careful not to damage the 1st and reverse brake return spring sub-assembly and automatic transmission case sub-assembly.
Tape the screwdriver tip before use.
35760
6.INSTALL REAR PLANETARY GEAR ASSEMBLY
Coat the thrust bearing race with ATF and install it to the automatic transmission case sub-assembly.
| Item | Inside (mm (in.)) | Outside (mm (in.)) |
|---|---|---|
| Thrust Needle Roller Bearing K | 21.0 (0.827) | 41.5 (1.634) |
| Thrust Bearing Race K | 23.13 (0.911) | 41.5 (1.634) |
| Thrust Needle Roller Bearing L | 43.55 (1.715) | 61.0 (2.402) |
| Thrust Bearing Race L | 47.1 (1.854) | 67.1 (2.642) |
| *1 | Thrust Needle Roller Bearing K |
| *2 | Thrust Bearing Race K |
| *3 | Thrust Needle Roller Bearing L |
| *4 | Thrust Bearing Race L |
Be sure to install the thrust needle roller bearing and thrust bearing race in the correct direction.
Coat the 2 thrust needle roller bearings and thrust bearing race with ATF and install them to the rear planetary gear assembly.
Install the rear planetary gear assembly to the automatic transmission case sub-assembly.
35684
7.INSTALL NO. 4 BRAKE DISC
Install the 2 No. 4 brake flanges, 7 No. 4 brake discs and 6 No. 4 brake plates to the automatic transmission case sub-assembly.
| *1 | No. 4 Brake Flange |
| *2 | No. 4 Brake Disc |
| *3 | No. 4 Brake Plate |
Make sure that the No. 4 brake discs, No. 4 brake plates and No. 4 brake flanges are installed in the correct order.
Install the thicker No. 4 brake flange first, and then install the thinner one.
35713
8.INSTALL INTERMEDIATE SHAFT
Coat the thrust needle roller bearing and thrust bearing race with ATF and install them to the intermediate shaft.
| Item | Inside (mm (in.)) | Outside (mm (in.)) |
|---|---|---|
| Thrust Needle Roller Bearing J | 32.1 (1.264) | 49.35 (1.943) |
| Thrust Bearing Race J
(Rear Race) |
32.1 (1.264) | 49.0 (1.929) |
| *1 | Thrust Needle Roller Bearing J |
| *2 | Thrust Bearing Race J (Rear Race) |
Install the intermediate shaft to the automatic transmission case sub-assembly.
35761
9.INSTALL REAR PLANETARY RING GEAR
Install the rear planetary ring gear to the rear planetary ring gear flange sub-assembly.
| *1 | Rear Planetary Ring Gear Flange Sub-assembly |
| *2 | Rear Planetary Ring Gear |
Using a screwdriver, install the snap ring to the rear planetary ring gear flange sub-assembly with rear planetary ring gear.
| *a | Protective Tape |
Be careful not to damage the rear planetary ring gear flange sub-assembly with rear planetary ring gear.
Tape the screwdriver tip before use.
35077D
10.INSTALL REAR PLANETARY RING GEAR FLANGE SUB-ASSEMBLY WITH REAR PLANETARY RING GEAR
Coat the thrust bearing race with ATF and install it to the rear planetary ring gear flange sub-assembly with rear planetary ring gear.
| Item | Inside (mm (in.)) | Outside (mm (in.)) |
|---|---|---|
| Thrust Bearing Race J
(Front Race) |
33.4 (1.315) | 49.0 (1.929) |
| *1 | Thrust Bearing Race J (Front Race) |
Be sure to install the thrust bearing race in the correct direction.
Install the rear planetary ring gear flange sub-assembly with rear planetary ring gear to the automatic transmission case sub-assembly.
35797B
11.INSTALL ONE-WAY CLUTCH INNER RACE
Install the one-way clutch inner race to the No. 3 one-way clutch assembly.
| *1 | One-way Clutch Inner Race |
| *2 | No. 3 One-way Clutch Assembly |
Rotate the one-way clutch inner race clockwise to install it.
35770C
12.INSTALL NO. 3 ONE-WAY CLUTCH ASSEMBLY WITH ONE-WAY CLUTCH INNER RACE
Install the No. 3 one-way clutch assembly with one-way clutch inner race to the automatic transmission case sub-assembly.
Using SST, install the snap ring to the automatic transmission case sub-assembly.
| *1 | Snap Ring |
| *a | 19° |
| *b | 49° |
|
Front Side |
Install the snap ring so that the tapered side is facing out.
Be sure to install the snap ring so that the ends of the snap ring are within the area shown in the illustration.
35689
13.INSPECT CLEARANCE OF NO. 4 BRAKE
35621V
14.INSTALL NO. 1 BRAKE PISTON
Coat 2 new O-rings with ATF and install them to the No. 1 brake piston.
With the No. 1 brake piston return spring sub-assembly installed to the No. 1 brake piston, align the 2 claws of the No. 1 brake piston return spring sub-assembly with the 2 claws of the No. 1 brake cylinder, and then install the No. 1 brake piston to the No. 1 brake cylinder.
35698
15.INSTALL NO. 1 BRAKE CYLINDER WITH NO. 1 BRAKE PISTON
Install the No. 1 brake cylinder with No. 1 brake piston to the automatic transmission case sub-assembly while making sure that the 2 claws of the No. 1 brake cylinder with No. 1 brake piston are positioned as shown in the illustration.
35608J
16.INSTALL NO. 1 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY
Align the 2 claws of the No. 1 brake piston return spring sub-assembly with the 2 claws of the No. 1 brake cylinder, and then install the No. 1 brake piston return spring sub-assembly to the No. 1 brake piston.
Place SST on the No. 1 brake piston return spring sub-assembly, and compress the No. 1 brake piston return spring sub-assembly with a press.
| *a | Turn |
Using a screwdriver, install the snap ring to the automatic transmission case sub-assembly.
| *a | 22.5° |
| *b | 37.5° |
Be sure to install the snap ring so that the ends of the snap ring are within the area shown in the illustration.
Be careful not to damage the automatic transmission case sub-assembly.
Tape the screwdriver tip before use.
35681A
17.INSTALL NO. 1 BRAKE DISC
Install the No. 1 brake flange, 4 No. 1 brake discs and 4 No. 1 brake plates to the automatic transmission case sub-assembly.
| *1 | No. 1 Brake Flange |
| *2 | No. 1 Brake Disc |
| *3 | No. 1 Brake Plate |
Make sure that the No. 1 brake discs, No. 1 brake plates and No. 1 brake flange are installed in the correct order.
Using a screwdriver, install the snap ring to the automatic transmission case sub-assembly.
| *a | 22.5° |
| *b | 37.5° |
Be sure to install the snap ring so that the ends of the snap ring are within the area shown in the illustration.
Be careful not to damage the automatic transmission case sub-assembly.
Tape the screwdriver tip before use.
35676B
18.INSPECT CLEARANCE OF NO. 1 BRAKE
35719B
19.INSTALL PLANETARY SUN GEAR
Install the planetary sun gear to the automatic transmission case sub-assembly.
35750
20.INSTALL CENTER PLANETARY GEAR ASSEMBLY
Coat the thrust bearing race with ATF and install it to the center planetary gear assembly.
| Item | Inside (mm (in.)) | Outside (mm (in.)) |
|---|---|---|
| Thrust Bearing Race I | 53.7 (2.114) | 74.0 (2.913) |
| *1 | Thrust Bearing Race I |
Install the center planetary gear assembly to the automatic transmission case sub-assembly.
35763
21.INSTALL CENTER PLANETARY RING GEAR
Install the center planetary ring gear to the center planetary ring gear flange
| *1 | Center Planetary Ring Gear Flange |
| *2 | Center Planetary Ring Gear |
Using a screwdriver, install the snap ring to the center planetary ring gear flange with center planetary ring gear.
| *a | Protective Tape |
Be careful not to damage the center planetary ring gear flange with center planetary ring gear.
Tape the screwdriver tip before use.
35769
22.INSTALL CENTER PLANETARY RING GEAR FLANGE WITH CENTER PLANETARY RING GEAR
Coat the 2 thrust needle roller bearings with ATF and install them to the center planetary ring gear flange with center planetary ring gear.
| Item | Inside (mm (in.)) | Outside (mm (in.)) |
|---|---|---|
| Thrust Needle Roller Bearing H | 63.3 (2.492) | 78.8 (3.102) |
| Thrust Needle Roller Bearing I | 55.7 (2.193) | 76.4 (3.008) |
| *1 | Thrust Needle Roller Bearing H |
| *2 | Thrust Needle Roller Bearing I |
Be sure to install the thrust needle roller bearing in the correct direction.
Install the center planetary ring gear flange with center planetary ring gear to the automatic transmission case sub-assembly.
35682A
23.INSTALL NO. 2 BRAKE DISC
Install the 2 No. 2 brake flanges, 5 No. 2 brake discs and 4 No. 2 brake plates to the automatic transmission case sub-assembly.
| *1 | No. 2 Brake Flange |
| *2 | No. 2 Brake Disc |
| *3 | No. 2 Brake Plate |
Make sure that the No. 2 brake discs, No. 2 brake plates and No. 2 brake flanges are installed in the correct order.
Install the thicker No. 2 brake flange first, and then install the thinner one.
35622G
24.INSTALL NO. 2 BRAKE PISTON
Coat 2 new O-rings with ATF and install them to the No. 2 brake piston.
With the No. 2 brake piston return spring sub-assembly installed to the No. 2 brake piston, align the claw of the No. 2 brake piston return spring sub-assembly with the claw of the No. 2 brake cylinder, and then install the No. 2 brake piston to the No. 2 brake cylinder.
Be careful not to damage the O-rings.
35699
25.INSTALL NO. 2 BRAKE CYLINDER WITH NO. 2 BRAKE PISTON
Install the No. 2 brake piston return spring sub-assembly to the automatic transmission case sub-assembly while making sure that the claw of the No. 2 brake piston return spring sub-assembly is positioned as shown in the illustration.
Install the No. 2 brake cylinder with No. 2 brake piston to the automatic transmission case sub-assembly while making sure that the claw of the No. 1 brake cylinder with No. 1 brake piston is positioned as shown in the illustration.
Place SST on the No. 2 brake cylinder, and compress the No. 2 brake piston return spring sub-assembly with a press.
| *a | Turn |
Using a screwdriver, install the snap ring to the automatic transmission case sub-assembly.
| *a | 30° |
Be sure to install the snap ring so that the ends of the snap ring are within the area shown in the illustration.
Be careful not to damage the automatic transmission case sub-assembly.
Tape the screwdriver tip before use.
35678B
26.INSPECT CLEARANCE OF NO. 2 BRAKE
35076C
27.INSTALL FRONT PLANETARY RING GEAR FLANGE SUB-ASSEMBLY
Set the snap ring onto the front planetary ring gear flange sub-assembly. Using needle-nose pliers, insert the snap ring into the front planetary ring gear while squeezing it, and then expand the snap ring to install it.
| *1 | Front Planetary Ring Gear |
| *2 | Snap Ring |
| *3 | Front Planetary Ring Gear Flange Sub-assembly |
Make sure the snap ring is securely inserted into the groove of the front planetary ring gear.
35743
28.INSTALL FRONT PLANETARY RING GEAR WITH FRONT PLANETARY RING GEAR FLANGE SUB-ASSEMBLY
Coat the thrust needle roller bearing and thrust bearing race with ATF and install them to the front planetary ring gear with front planetary ring gear flange sub-assembly.
| Item | Inside (mm (in.)) | Outside (mm (in.)) |
|---|---|---|
| Thrust Needle Roller Bearing G | 63.3 (2.492) | 78.8 (3.102) |
| Thrust Bearing Race H | 66.3 (2.610) | 78.9 (3.106) |
| *1 | Thrust Needle Roller Bearing G |
| *2 | Thrust Bearing Race H |
Be sure to install the thrust needle roller bearing and thrust bearing race in the correct direction.
Install the front planetary ring gear with front planetary ring gear flange sub-assembly to the automatic transmission case sub-assembly.
35720
29.INSTALL FRONT PLANETARY GEAR ASSEMBLY
Coat the 2 thrust bearing races with ATF and install them to the front planetary gear assembly.
| Item | Inside (mm (in.)) | Outside (mm (in.)) |
|---|---|---|
| Thrust Bearing Race F | 44.0 (1.732) | 62.8 (2.472) |
| Thrust Bearing Race G | 65.8 (2.591) | 86.3 (3.398) |
| *1 | Thrust Bearing Race F |
| *2 | Thrust Bearing Race G |
Be sure to install the thrust bearing race in the correct direction.
Install the front planetary gear assembly to the automatic transmission case sub-assembly.
35709J
30.INSTALL SUN GEAR INPUT DRUM SUB-ASSEMBLY
Coat the thrust needle roller bearing and thrust bearing race with ATF and install them to the sun gear input drum sub-assembly.
| Item | Inside (mm (in.)) | Outside (mm (in.)) |
|---|---|---|
| Thrust Bearing Race E | 40.83 (1.607) | 52.8 (2.079) |
| Thrust Needle Roller Bearing F | 37.1 (1.461) | 61.2 (2.409) |
| *1 | Thrust Bearing Race E |
| *2 | Thrust Needle Roller Bearing F |
Be sure to install the thrust needle roller bearing and thrust bearing race in the correct direction.
Install the sun gear input drum sub-assembly to the automatic transmission case sub-assembly.
35061
31.INSTALL FORWARD CLUTCH HUB SUB-ASSEMBLY
Coat the 2 thrust needle roller bearings with ATF and install them to the forward clutch hub sub-assembly.
| Item | Inside (mm (in.)) | Outside (mm (in.)) |
|---|---|---|
| Thrust Needle Roller Bearing D | 33.3 (1.311) | 56.6 (2.228) |
| Thrust Needle Roller Bearing E | 39.6 (1.559) | 52.8 (2.079) |
| *1 | Thrust Needle Roller Bearing D |
| *2 | Thrust Needle Roller Bearing E |
Be sure to install the thrust needle roller bearing in the correct direction.
Install the forward clutch hub sub-assembly to the automatic transmission case sub-assembly.
35631
32.INSTALL MULTIPLE DISC CLUTCH HUB
Coat the 2 thrust bearing races with ATF and install them to the multiple disc clutch hub.
| Item | Inside (mm (in.)) | Outside (mm (in.)) |
|---|---|---|
| Thrust bearing race C | 22.0 (0.866) | 44.8 (1.764) |
| Thrust bearing race D | 38.4 (1.512) | 56.5 (2.224) |
| *1 | Thrust bearing race C |
| *2 | Thrust bearing race D |
Be sure to install the thrust bearing race in the correct direction.
Install the multiple disc clutch hub to the automatic transmission case sub-assembly.
35606A
33.INSTALL DIRECT CLUTCH PISTON
Coat 2 new O-rings with ATF, and install them to the direct clutch piston.
Install the direct clutch piston to the direct clutch drum sub-assembly.
Be careful not to damage the O-rings.
35669
34.INSTALL NO. 2 CLUTCH BALANCER
Install the direct clutch return spring sub-assembly to the direct clutch piston.
| *1 | No. 2 Clutch Balancer |
| *2 | Direct Clutch Return Spring Sub-assembly |
Coat a new O-ring with ATF, and install it to the No. 2 clutch balancer.
Install the No. 2 clutch balancer to the direct clutch drum sub-assembly.
Be careful not to damage the O-ring.
Place SST on the No. 2 clutch balancer, and compress the direct clutch return spring sub-assembly with a press.
Stop pressing when the spring sheet is lowered to the place 1 to 2 mm (0.0394 to 0.0787 in.) from the snap ring groove to prevent the spring sheet from being deformed.
Using SST, install the snap ring.
Do not expand the snap ring excessively.
35667A
35.INSTALL NO. 2 CLUTCH DISC (DIRECT CLUTCH DISC)
Install the 5 No. 2 clutch plates, 5 No. 2 clutch discs and direct clutch flange to the direct clutch drum sub-assembly.
| *1 | Direct Clutch Flange |
| *2 | No. 2 Clutch Disc |
| *3 | No. 2 Clutch Plate |
Make sure that the No. 2 clutch discs, No. 2 clutch plates and direct clutch flange are installed in the correct order.
Using a screwdriver, install the snap ring to the direct clutch drum sub-assembly.
| *a | Protective Tape |
Be careful not to damage the direct clutch drum sub-assembly.
Tape the screwdriver tip before use.
35675C
36.INSPECT CLEARANCE OF NO. 2 CLUTCH (DIRECT CLUTCH)
35612B
37.INSTALL FORWARD CLUTCH PISTON
Coat a new O-ring with ATF, and install it to the input shaft sub-assembly.
Coat a new O-ring with ATF, and install it to the forward clutch piston.
Install the forward clutch piston to the input shaft sub-assembly.
Be careful not to damage the O-rings.
35668
38.INSTALL NO. 1 CLUTCH BALANCER
Coat a new O-ring with ATF, and install it to the No. 1 clutch balancer.
Install the forward clutch return spring sub-assembly and No. 1 clutch balancer to the input shaft sub-assembly.
| *1 | No. 1 Clutch Balancer |
| *2 | Forward Clutch Return Spring Sub-assembly |
Be careful not to damage the O-ring.
Place SST on the No. 1 clutch balancer, and compress the forward clutch return spring sub-assembly with a press.
Stop pressing when the spring sheet is lowered to the place 1 to 2 mm (0.0394 to 0.0787 in.) from the snap ring groove to prevent the spring sheet from being deformed.
Using SST, install the snap ring.
Do not expand the snap ring excessively.
35633B
39.INSTALL NO. 1 CLUTCH DISC (FORWARD CLUTCH DISC)
Install the 5 No. 1 clutch plates, 5 No. 1 clutch discs and forward clutch flange to the input shaft sub-assembly.
| *1 | Forward Clutch Flange |
| *2 | No. 1 Clutch Disc |
| *3 | No. 1 Clutch Plate |
Make sure that the No. 1 clutch discs, No. 1 clutch plates and forward clutch flange are installed in the correct order.
Using a screwdriver, install the snap ring.
| *a | Protective Tape |
Be careful not to damage the input shaft sub-assembly.
Tape the screwdriver tip before use.
35635
40.INSPECT CLEARANCE OF NO. 1 CLUTCH (FORWARD CLUTCH DISC)
35617
41.INSTALL CLUTCH DRUM OIL SEAL RING
Coat 3 new clutch drum oil seal rings with ATF and install them to the input shaft sub-assembly.
Do not expand the clutch drum oil seal ring ends excessively.
After installing the clutch drum oil seal rings, check that they rotate smoothly.
35605A
42.INSTALL DIRECT CLUTCH DRUM SUB-ASSEMBLY
Install the direct clutch drum sub-assembly to the input shaft sub-assembly.
| *1 | Direct Clutch Drum Sub-assembly |
| *2 | Input Shaft Sub-assembly |
43.INSTALL CLUTCH DRUM AND INPUT SHAFT ASSEMBLY
Coat the 3 thrust needle roller bearings with ATF and install them to the clutch drum and input shaft assembly.
| Item | Inside (mm (in.)) | Outside (mm (in.)) |
|---|---|---|
| Thrust Needle Roller Bearing A | 71.9 (2.831) | 85.6 (3.370) |
| Thrust Needle Roller Bearing B | 34.6 (1.362) | 52.0 (2.047) |
| Thrust Needle Roller Bearing C | 21.3 (0.839) | 41.1 (1.618) |
| *1 | Thrust Needle Roller Bearing A |
| *2 | Thrust Needle Roller Bearing B |
| *3 | Thrust Needle Roller Bearing C |
Be sure to install the thrust needle roller bearing in the correct direction.
Install the clutch drum and input shaft assembly to the automatic transmission case sub-assembly.
44.INSTALL OIL PUMP ASSEMBLY
Coat the 2 thrust bearing races with ATF and install them to the oil pump assembly.
| Item | Inside (mm (in.)) | Outside (mm (in.)) |
|---|---|---|
| Thrust Bearing Race B | 40.0 (1.575) | 52.8 (2.079) |
| Thrust Bearing Race A | 74.2 (2.921) | 87.74 (3.454) |
| *1 | Thrust Bearing Race B |
| *2 | Thrust Bearing Race A |
| *3 | Oil Pump O-ring |
Be sure to install the thrust bearing race in the correct direction.
Coat a new oil pump O-ring with ATF, and install it to the oil pump assembly.
Set the oil pump assembly on the input shaft, and align the bolt holes of the oil pump assembly with the automatic transmission case sub-assembly.
Be careful not to damage the oil pump O-ring.
Temporarily install the oil pump assembly to the automatic transmission case sub-assembly.
Install the oil pump assembly with the 10 bolts.
35506F
45.INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL
Using SST and a hammer, drive in 2 new manual valve lever shaft oil seals to the automatic transmission case sub-assembly.
-0.5 to 0.5 mm (-0.0196 to 0.0196 in.)
Coat the lip of the manual valve lever shaft oil seal with MP grease.
35505
46.INSTALL MANUAL VALVE LEVER SUB-ASSEMBLY
Install a new spacer to the manual valve lever sub-assembly.
| *1 | Manual Valve Lever Sub-assembly |
| *2 | Spacer |
Install the manual valve lever shaft to the automatic transmission case sub-assembly through the manual valve lever sub-assembly.
Using a hammer, drive in a new spring pin.
Turn the spacer and manual valve lever shaft to align the smaller hole on the spacer with the indent on the manual valve lever sub-assembly.
Using a 3 mm pin punch and a hammer, stake the spacer.
Check that the spacer does not turn.
Make sure that the shaft rotates smoothly.
35556
47.INSTALL PARKING LOCK PAWL SHAFT
Install the E-ring to the parking lock pawl shaft.
Install the parking lock pawl, parking lock pawl shaft and spring to the automatic transmission case sub-assembly.
| *1 | Parking Lock Pawl |
| *2 | E-ring |
| *3 | Parking Lock Pawl Shaft |
| *4 | Spring |
35501
48.INSTALL PARKING LOCK ROD SUB-ASSEMBLY
Install the parking lock rod sub-assembly to the manual valve lever sub-assembly.
35595
49.INSTALL PARKING LOCK PAWL BRACKET
Install the parking lock pawl bracket to the automatic transmission case sub-assembly with the 3 bolts.
Move the manual valve lever sub-assembly to P, and check the output shaft is locked by the parking lock pawl.
35159
50.INSTALL BRAKE DRUM GASKET
Coat 2 new brake drum gaskets with ATF and install them to the automatic transmission case sub-assembly.
35145C
51.INSTALL TRANSMISSION CASE GASKET
Coat 2 new transmission case gaskets with ATF and install them to the automatic transmission case sub-assembly.
35410
52.INSTALL TRANSMISSION VALVE BODY ASSEMBLY
Insert the manual valve lever sub-assembly into the groove on the end of the manual valve and install the transmission valve body assembly to the automatic transmission case sub-assembly with the 12 bolts.
| *1 | Manual Valve Lever Sub-assembly |
| *2 | Manual Valve |
Each bolt length is indicated below.
25 mm (0.984 in.)
36 mm (1.42 in.)
50 mm (1.97 in.)
Install the detent spring and detent spring cover to the transmission valve body assembly with the bolt.
35330
53.INSTALL VALVE BODY OIL STRAINER ASSEMBLY
Coat a new O-ring with ATF, and install it to the valve body oil strainer assembly.
Install the valve body oil strainer assembly to the transmission valve body assembly with the 3 bolts.
82125J
54.INSTALL TRANSMISSION WIRE
Coat 2 new O-rings with ATF, and install them to the 2 temperature sensors.
Coat a new O-ring with ATF, and install it to the transmission wire.
Install the transmission wire to the automatic transmission case sub-assembly with the bolt.
w/ Stop and Start System:
Connect the electromagnetic oil pump connector.
| *A | w/ Stop and Start System |
| *1 | Temperature Sensor Clamp |
| *2 | Temperature Sensor |
Connect the 7 solenoid valve connectors.
Install the 2 temperature sensors and 2 temperature sensor clamps to the transmission valve body assembly with the bolt.
35106
55.INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY
Install the 4 transmission oil cleaner magnets to the automatic transmission oil pan sub-assembly as shown in the illustration.
Install a new automatic transmission oil pan gasket to the automatic transmission oil pan sub-assembly.
Install the automatic transmission oil pan sub-assembly with automatic transmission oil pan gasket to the automatic transmission case sub-assembly with the 10 bolts.
| *1 | Sleeve |
| *2 | Automatic Transmission Case Sub-assembly |
| *a | Correct |
| *b | Incorrect |
| *c | Protrusion |
Make sure that automatic transmission oil pan gasket seal surface and automatic transmission oil pan sub-assembly contact surface are free of oil and foreign matter.
Install the automatic transmission oil pan gasket so that there is no slack in the automatic transmission oil pan gasket, and the entire seal surface is level.
Make sure that the 8 protrusions are properly engaged to the automatic transmission oil pan sub-assembly.
When installing the automatic transmission oil pan sub-assembly, make sure that the automatic transmission oil pan gasket is not pinched between the sleeve and the seal surface of the automatic transmission case sub-assembly.
Install the drain plug and a new gasket to the automatic transmission oil pan sub-assembly.
Using a 5 mm hexagon socket wrench, install a new gasket and overflow plug to the automatic transmission oil pan sub-assembly.
35111
56.INSTALL AUTOMATIC TRANSMISSION HOUSING
Clean and degrease the bolts and bolt holes with non-residue solvent.
Install the automatic transmission housing to the automatic transmission case sub-assembly with the 8 bolts.
Apply adhesive to 2 or 3 threads on the end of the 4 bolts.
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
Install 4 bolts to the automatic transmission housing.
35157B
57.INSTALL REAR TRANSFER CASE ADAPTER OIL RECEIVER
Install the rear transfer case adapter oil receiver to the transfer adapter sub-assembly.
Using snap ring pliers, install the snap ring to the transfer adapter sub-assembly.
36117A
58.INSTALL TRANSFER ADAPTER OIL SEAL
Using SST and a hammer, drive in a new transfer adapter oil seal to the transfer adapter sub-assembly.
0 to 0.5 mm (0 to 0.0196 in.)
Coat the lip of the transfer adapter oil seal with MP grease.
35015G
59.INSTALL TRANSFER ADAPTER SUB-ASSEMBLY
Using a plastic-faced hammer, tap 2 new straight pins into the transfer adapter sub-assembly.
5.7 to 6.3 mm (0.225 to 0.248 in.)
It is not necessary to remove the straight pins they are being replaced.
Clean and degrease the threads of the 10 bolts, bolt holes and the contact surfaces of the automatic transmission case sub-assembly and transfer adapter sub-assembly with non-residue solvent.
Apply seal packing to the transfer adapter sub-assembly as shown in the illustration.
Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent
| *a | Seal Packing |
Apply seal packing in a continuous line (width 1.2 mm (0.0472 in.)) along the sealing surface.
After applying seal packing, install the transfer adapter sub-assembly to the automatic transmission case sub-assembly within 3 minutes and tighten the bolts within 10 minutes.
Apply adhesive to 2 or 3 threads on the end of the 10 bolts.
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
Install the transfer adapter sub-assembly to the automatic transmission case sub-assembly with the 10 bolts.
Each bolt length is indicated below.
40 mm (1.57 in.)
50 mm (1.97 in.)
60.INSTALL OIL COOLER TUBE UNION
Coat 2 new O-rings with ATF and install them to the 2 oil cooler tube unions.
Using SST, install the 2 oil cooler tube unions to the automatic transmission case sub-assembly.
| *a | Torque Wrench Fulcrum Length |
| *b | 18° to 22° |
| *c | -2° to 2° |
| *d | Turn |
| *e | Hold |
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
(See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION)
When using SST (fulcrum length of 34.5 mm (1.3583 in.)) + torque wrench (fulcrum length of 180 mm (7.0866 in.)): 25 N*m (252 kgf*cm, 18 ft.*lbf)
35104A
61.INSTALL AUTOMATIC TRANSMISSION CASE PLUG
Coat 6 new O-rings with ATF, and install them to the 6 automatic transmission case plugs.
Install the 6 automatic transmission case plugs to the automatic transmission case sub-assembly.
Coat a new O-ring with ATF, and install it to the automatic transmission case plug.
Using a T55 "TORX" socket wrench, install the automatic transmission case plug to the automatic transmission case sub-assembly.
35104A
62.INSTALL REFILL PLUG
Coat a new O-ring with ATF, and install it to the refill plug.
Install the refill plug to the transfer adapter sub-assembly.
84540
63.INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY
Make sure that the manual valve lever shaft has not been rotated prior to installing the park/neutral position switch assembly as the detent spring may become detached from the manual valve lever shaft.
Clean the bolt and bolt hole.
Apply adhesive to 2 or 3 threads on the end of the bolt.
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
Install the bolt within 3 minutes of applying adhesive.
Temporarily install the park/neutral position switch assembly to the automatic transmission case sub-assembly with the bolt.
Install the lock washer and nut to the park/neutral position switch assembly.
Temporarily install the transmission control shaft lever LH to the manual valve lever shaft with the spring washer and nut.
Turn the transmission control shaft lever LH clockwise until it stops, and then return the transmission control shaft lever LH counterclockwise 2 notches to N.
Align the neutral basic line with the groove as shown in the illustration, and tighten the bolt.
| *a | Neutral Basic Line |
| *b | Groove |
Using a screwdriver, bend the tabs of the lock washer.
Be careful not to damage the park/neutral position switch assembly.
Bend at least 2 of the lock washer tabs.
Tape the screwdriver tip before use.
35573
64.INSTALL TRANSMISSION CONTROL SHAFT LEVER LH
Install the transmission control shaft lever LH to the manual valve lever shaft with the spring washer and nut.
89413B
65.INSTALL TRANSMISSION REVOLUTION SENSOR
Coat a new O-ring with ATF, and install it to the transmission revolution sensor (NT).
Install the transmission revolution sensor (NT) to the automatic transmission case sub-assembly with the bolt.
Coat a new O-ring with ATF, and install it to the transmission revolution sensor (SP2).
Install the transmission revolution sensor (SP2) to the automatic transmission case sub-assembly with the bolt.
35104V
66.INSTALL BREATHER PLUG HOSE
Install the breather plug sub-assembly and breather plug to the breather plug hose.
| *1 | Breather Plug Sub-assembly |
| *2 | Breather Plug Hose |
| *3 | Breather Plug |
| *4 | O-ring |
Coat a new O-ring with ATF, and install it to the breather plug.
Install the breather plug hose to the automatic transmission case sub-assembly.
Be careful not to damage the O-rings.