DATA LIST
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Vehicle Speed | Vehicle speed/
Min.: 0 km/h (0 mph) Max.: 255 km/h (158 mph) |
Actual vehicle speed | - |
| Engine Speed | Engine speed/
Min.: 0 rpm Max.: 16384 rpm |
600 to 700 rpm: Idling | - |
| Coolant Temp | Engine coolant temperature/
Min.: -40°C (-40°F) Max.: 140°C (284°F) |
80 to 100°C (176 to 212°F): After warming up | ·
If value -40°C (-40°F): sensor circuit open ·
If value 140°C (284°F): sensor circuit shorted |
| Battery Voltage | Battery voltage/
Min.: 0 V Max.: 66.000 V |
11 to 14 V: Engine switch on (IG) | - |
| Accelerator Position | Accelerator pedal position/
Min.: 0% Max.: 399.9% |
Actual accelerator pedal position | - |
| N Range Status | Shift lever N status/
ON or OFF |
·
ON: Shift lever in P or N ·
OFF: Shift lever not in P or N |
- |
| Neutral Position SW Signal | Park/neutral position switch status/
ON or OFF |
·
ON: Shift lever in P or N ·
OFF: Shift lever not in P or N |
When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect.
|
| Transfer L4 | Transfer status/
ON or OFF |
·
ON: Transfer in L4 ·
OFF: Transfer not in L4 |
- |
| Stop Light Switch | Stop light switch status/
ON or OFF |
·
ON: Brake pedal depressed ·
OFF: Brake pedal released |
- |
| SPD (NT) | Input shaft speed/
Min.: 0 rpm Max.: 12750 rpm |
·
Lock-up on (after warming up the engine): Value from transmission revolution sensor (NT) equal to engine speed ·
Lock-up off (idling with shift lever in N): Value from transmission revolution sensor (NT) nearly equal to engine speed |
Data is displayed in increments of 50 rpm. |
| SPD (SP2) | Output shaft speed/
Min.: 0 km/h (0 mph) Max.: 255 km/h (158 mph) |
0 km/h (0 mph): Vehicle stopped (equal to vehicle speed) | - |
| Shift SW Status (P Range) | Park/neutral position switch status/
ON or OFF |
·
ON: Shift lever in P ·
OFF: Shift lever not in P |
When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect.
|
| Pattern Switch (PWR/M) | SPORT mode status*/
ON or OFF |
·
ON: SPORT mode on ·
OFF: SPORT mode off |
- |
| Shift SW Status (R Range) | Park/neutral position switch status/
ON or OFF |
·
ON: Shift lever in R ·
OFF: Shift lever not in R |
When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect.
|
| Shift SW Status (N Range) | Park/neutral position switch status/
ON or OFF |
·
ON: Shift lever in N ·
OFF: Shift lever not in N |
When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect.
|
| Shift SW Status (N, P Range) Supported | Status of park/neutral position switch (N or P) supported/
Supp or Unsupp |
- | - |
| Shift SW Status (N, P Range) | Park/neutral position switch status/
ON or OFF |
·
ON: Shift lever in P or N ·
OFF: Shift lever not in P or N |
- |
| Sports Shift Up SW | Sport shift up switch status/
ON or OFF |
·
ON: Shift lever held in "+" (up-shift) ·
OFF: Shift lever not held in "+" (up-shift) ·
ON: "+" shift paddle operated and held (up-shift) (w/ Shift Paddle Switch) ·
OFF: "+" shift paddle not operated (up-shift) (w/ Shift Paddle Switch) |
- |
| Sports Shift Down SW | Sport shift down switch status/
ON or OFF |
·
ON: Shift lever held in "-" (down-shift) ·
OFF: Shift lever not held in "-" (down-shift) ·
ON: "-" shift paddle operated and held (down-shift) (w/ Shift Paddle Switch) ·
OFF: "-" shift paddle not operated (down-shift) (w/ Shift Paddle Switch) |
- |
| Sports Mode Selection SW | Sport mode select switch status/
ON or OFF |
·
ON: Shift lever in S, "+" or "-" ·
OFF: Shift lever not in S, "+" or "-" |
- |
| Snow Switch Status | 2ND START switch status/
ON or OFF |
·
ON: 2ND START switch pushed and held ·
OFF: 2ND START switch not pushed |
- |
| Shift SW Status (D Range) | Park/neutral position switch status/
ON or OFF |
·
ON: Shift lever in D, S, "+" or "-" ·
OFF: Shift lever not in D, S, "+" or "-" |
When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect.
|
| A/T Oil Temperature 1 | No. 1 ATF temperature sensor value/
Min.: -40°C (-40°F) Max.: 150°C (302°F) |
·
Approx. 80°C (176°F): After stall test ·
Equal to ambient temperature when cold soak |
If the value -40°C (-40°F) or 150°C (302°F), No. 1 ATF temperature sensor circuit is open or shorted. |
| A/T Oil Temperature 2 | No. 2 ATF temperature sensor value/
Min.: -40°C (-40°F) Max.: 150°C (302°F) |
·
Approx. 80°C (176°F): After stall test ·
Equal to ambient temperature when cold soak |
If the value -40°C (-40°F) or 150°C (302°F), No. 2 ATF temperature sensor circuit is open or shorted. |
| ATF Thermal Degradation Estimate | Estimated value of ATF thermal degradation/
Min.: 0 Max.: 65535 |
- | If 50000 or more is displayed for the Data List item "ATF Thermal Degradation Estimate", thermal degradation of the ATF is suspected. Perform ATF Thermal Degradation Estimate Reset after replacing the ATF. |
| NT Sensor Voltage | Transmission revolution sensor (NT) output voltage/
Min.: 0.000 V Max.: 4.999 V |
0.1 to 1.9 V: Engine idling | - |
| SP2 Sensor Voltage | Transmission revolution sensor (SP2) output voltage/
Min.: 0.000 V Max.: 4.999 V |
0.1 to 1.9 V: Engine idling | - |
| Normal Mode Switch | NORMAL switch (eco mode switch (drive mode)) status*/
ON or OFF |
·
ON: NORMAL mode switch pushed and held ·
OFF: NORMAL mode switch not pushed |
- |
| Sports Mode Switch | SPORT switch (eco mode switch (drive mode)) status*/
ON or OFF |
·
ON: SPORT mode switch pushed and held ·
OFF: SPORT mode switch not pushed |
- |
| Lock Up | Lock up/
ON or OFF |
·
ON: Lock-up operating ·
OFF: Lock-up not operating |
- |
| Shift Status | ECM gear shift command/
1st, 2nd, 3rd, 4th, 5th or 6th |
Same as actual gear | - |
| SLT Solenoid Status | Shift solenoid valve SLT status/
ON or OFF |
·
ON: Shift solenoid valve SLT operating ·
OFF: Shift solenoid valve SLT not operating |
- |
| SLU Solenoid Status | Shift solenoid valve SLU status/
ON or OFF |
·
ON: Shift solenoid valve SLU operating ·
OFF: Shift solenoid valve SLU not operating |
- |
| SL Solenoid Status | Shift solenoid valve SL status/
ON or OFF |
·
ON: Shift solenoid valve SL operating ·
OFF: Shift solenoid valve SL not operating |
- |
| Snow or 2nd Start Mode | 2ND START mode status/
ON or OFF |
·
ON: 2ND START mode on ·
OFF: 2ND START mode off |
- |
| Torque Converter Temperature Raise History | Torque converter temperature raise history status/
ON or OFF |
OFF | - |
*: w/ Drive Mode Switch
ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Warm up the engine.
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the GTS, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Connect the TC and TE1 | Changes to the fluid temperature detection mode. | ON/OFF | [Vehicle Condition]
·
Engine switch on (IG) ·
Vehicle stopped |
| Activate the Solenoid (SLU) | Operates shift solenoid valve SLU | ON/OFF | [Vehicle Condition]
·
Engine switch on (IG) ·
Engine stopped ·
Shift lever in P or N |
| Activate the Solenoid (SLT)* | Operates shift solenoid valve SLT to raise the line pressure. | ON/OFF
|
[Vehicle Condition]
·
Vehicle Stopped ·
Engine idling |
| Activate the Lock Up | Controls the shift solenoid valves SLU and SL to set the automatic transmission to the lock-up condition. | ON/OFF | Can be used to check shift solenoid valves SLU and SL operation.
[Vehicle Condition] ·
Vehicle speed: 70 km/h (44 mph) or more ·
Gear: Highest gear ·
Throttle valve opening angle: Less than 20% |
| Activate the Solenoid (SL) | Operates shift solenoid valve SL | ON/OFF | [Vehicle Condition]
·
Engine switch on (IG) ·
Engine stopped ·
Shift lever in P or N |
| Control the Shift Position | Operates the shift solenoid valves to allow gears to be selected manually. | ·
Press "→" button: Up-shift occurs ·
Press "←" button: Down-shift occurs |
Can be used to check the operation of the shift solenoid valves.
Up-shifts and down-shifts should be performed consecutively. A 10 second interval is required between gear changes. Do not down-shift at high speeds. Doing so will damage the automatic transmission. [Vehicle Condition] 50 km/h (31 mph) or less |
| Activate the Solenoid (SL1) | Operates shift solenoid valve SL1 | ON/OFF | [Vehicle Condition]
·
Engine switch on (IG) ·
Engine stopped ·
Shift lever in P or N |
| Activate the Solenoid (SL2) | Operates shift solenoid valve SL2 | ON/OFF | [Vehicle Condition]
·
Engine switch on (IG) ·
Engine stopped ·
Shift lever in P or N |
| Activate the Solenoid (SL3) | Operates shift solenoid valve SL3 | ON/OFF | [Vehicle Condition]
·
Engine switch on (IG) ·
Engine stopped ·
Shift lever in P or N |
| Activate the Solenoid (SL4) | Operates shift solenoid valve SL4 | ON/OFF | [Vehicle Condition]
·
Engine switch on (IG) ·
Engine stopped ·
Shift lever in P or N |
*: The "Activate the Solenoid (SLT)" Active Test is performed to allow confirmation that the line pressure changes. The line pressure changes are confirmed using the same SST that is used for the Hydraulic Test (See page Drivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for 1GR-FE)>HYDRAULIC TEST).
Note that the pressure readings for the Active Test and Hydraulic Test are different.