Home › Drivetrain › AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for 1GD-FTV) › from 2020.08
RM27T0E _52 Drivetrain _053698 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0260782 AUTOMATIC TRANSMISSION SYSTEM(for 1GD-FTV) C

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1GD-FTV)  P277115  Four Wheel Drive (4WD) Low Switch Circuit Short to Battery or Open  


DESCRIPTION

The ECM detects the signal from the transfer L4 position switch.

This DTC indicates that the transfer L4 position switch remains off.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P277115 Four Wheel Drive (4WD) Low Switch Circuit Short to Battery or Open Transfer L4 position switch remains off while the vehicle is being driven under the following conditions for 1.8 seconds or more (1 trip detection logic):
·

Output shaft speed is between 1000 and 3000 rpm.

·

Transfer position switch is in L4.


·

Open in transfer L4 position switch circuit

·

Transfer system

·

4 wheel drive control ECU

·

ECM


Comes on DTC stored SAE Code:
P2774

MONITOR DESCRIPTION

The ECM monitors the L4 position switch to determine when the transfer case L4 gears are engaged. If the transfer case H4 gears remain engaged under the following conditions, the ECM will conclude that there is a malfunction of the L4 position switch, illuminate the MIL and store the DTC:

·

The L4 switch indicates that the H4 transfer case gears are engaged.

·

The transfer position switch is in L4.

·

The transfer case output shaft speed is between 1000 and 3000 rpm.

·

The specified time period has elapsed.


CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Turn the transfer position switch to L4.

7.

Drive the vehicle at 15 to 20 km/h (9 to 12 mph) for 1.8 seconds or more.

8.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

9.

Input the DTC: P277115.

10.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transmission are replaced.

Click hereDrivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for 1GD-FTV)>INITIALIZATION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (L4 TERMINAL VOLTAGE)
a.
C136763C51
1.49,0.635 1.917,0.885 0.427,0.25 2.281,2.531 2.417,1.76 true 1.563,0.677 2.021,0.875 0.458,0.198 10 false G53 2.188,2.552 2.667,2.729 0.479,0.177 10 false L4 0.156,0.167 0.635,0.427 0.479,0.26 10 false *a
*a Front view of wire harness connector
(to 4 Wheel Drive Control ECU)


Disconnect the 4 wheel drive control ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G53-16 (L4) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - ECM)
2.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - ECM)
a.

Disconnect the 4 wheel drive control ECU connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G53-16 (L4) - C149-3 (L4) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR