Home › Drivetrain › AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for 1GD-FTV) › from 2020.08
RM27T0E _52 Drivetrain _053698 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0260782 AUTOMATIC TRANSMISSION SYSTEM(for 1GD-FTV) J

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1GD-FTV)  Pattern Select Switch 2nd Start Mode Circuit  


DESCRIPTION

When 2nd start mode is selected with the combination switch assembly (2nd start), the ECM controls the solenoid valves and the transmission starts from 2nd gear.

In 2nd start mode, the system operates the throttle motor to control engine output to reduce skidding of the drive wheels and guarantee stable acceleration from rest, straight driving and turning stability.

When the shift lever is in D, the transmission automatically shifts up from 2nd to 6th as usual.

HINT:
·

The combination switch assembly (2nd start) is a momentary-type switch.

·

In order to cancel 2nd start mode, push the combination switch assembly (2nd start) again or turn the ignition switch off.



WIRING DIAGRAM

C326150E59
6.323,1.073 6.656,1.26 0.333,0.188 10 false 12 V 5.917,3 6.458,3.198 0.542,0.198 10 false G184 5.917,3.167 6.271,3.365 0.354,0.198 10 false ECM 5.229,1.25 5.448,1.448 0.219,0.198 10 false 32 3.938,1.25 4.135,1.458 0.198,0.208 10 false 14 3.521,1.26 3.979,1.458 0.458,0.198 10 false 2ND 2.531,1.25 2.688,1.448 0.156,0.198 10 false E 2.281,1.24 2.563,1.458 0.281,0.219 10 false 24 5.49,1.26 6.104,1.458 0.615,0.198 10 false SNWI 2.469,1.969 2.958,2.156 0.49,0.188 10 false G156 2.469,2.167 3.792,2.583 1.323,0.417 10 false Combination Switch Assembly (2nd Start)

PROCEDURE

1.INSPECT COMBINATION SWITCH ASSEMBLY (2ND START)
a.
C331272C55
2.156,1.781 2.385,1.281 true 0.542,1.76 0.833,1.292 true 2.042,1.823 2.5,2.021 0.458,0.198 10 false 2ND 0.458,1.802 0.615,2 0.156,0.198 10 false E 0.208,0.125 0.521,0.323 0.313,0.198 10 false *a
*a Combination Switch Assembly (2nd Start)


Remove the combination switch assembly (2nd start) (See page Drivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>COMBINATION SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
14 (2ND) - 24 (E) 2ND START switch pushed and held Below 1 Ω
14 (2ND) - 24 (E) 2ND START switch not pushed 10 kΩ or higher



Result:
Result Proceed to
OK A
NG (w/ Module Switch) B
NG (w/o Module Switch) C


A

2.CHECK HARNESS AND CONNECTOR (COMBINATION SWITCH ASSEMBLY (2ND START) - BODY GROUND)

B

REPLACE COMBINATION SWITCH ASSEMBLY (w/ Module Switch (2nd Start))

C

REPLACE NO. 2 COMBINATION SWITCH ASSEMBLY (w/o Module Switch (2nd Start))

2.CHECK HARNESS AND CONNECTOR (COMBINATION SWITCH ASSEMBLY (2ND START) - BODY GROUND)
a.
C442002C01
1.51,0.219 1.958,0.427 0.448,0.208 2.865,1.844 2.646,1.365 true 1.552,0.24 2.167,0.438 0.615,0.198 10 false G156 2.875,1.906 3.094,2.156 0.219,0.25 10 false E 0.177,0.146 0.49,0.344 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Combination Switch Assembly (2nd Start))


Disconnect the combination switch assembly (2nd start) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G156-24 (E) - Body ground Always Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (COMBINATION SWITCH ASSEMBLY (2ND START) - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (COMBINATION SWITCH ASSEMBLY (2ND START) - ECM)
a.
C318001C27
2.219,0.198 2.656,0.438 0.438,0.24 2.292,2.063 2.938,2.719 false 0.104,0.073 0.615,0.281 0.51,0.208 10 false *a 2.26,0.24 2.771,0.448 0.51,0.208 10 false G184 2.667,2.771 3.396,2.979 0.729,0.208 10 false 9 (SNWI)
*a Rear view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G184-32 (SNWI) - Body ground 2ND START switch switch pushed and held Below 1 Ω
G184-32 (SNWI) - Body ground 2ND START switch switch not pushed 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR