A thermistor is built into the engine coolant temperature sensor and it changes its resistance value according to the engine coolant temperature.
The structure of the sensor and connection to the ECM is the same as that of the intake air temperature sensor.
If DTC P011511 or P011515 is stored, the ECM operates the fail-safe function in which the engine coolant temperature is assumed to be 80°C (176°F).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P011511 | Engine Coolant Temperature Sensor 1 Circuit Short to Ground | Short in the engine coolant temperature sensor circuit for 0.5 seconds.
(1 trip detection logic) |
·
Short in engine coolant temperature sensor circuit ·
Engine coolant temperature sensor ·
ECM |
Comes on | DTC stored | SAE Code: P0117 |
| P011515 | Engine Coolant Temperature Sensor 1 Circuit Short to Battery or Open | Open in the engine coolant temperature sensor circuit for 0.5 seconds.
(1 trip detection logic) |
·
Open in engine coolant temperature sensor circuit ·
Engine coolant temperature sensor ·
ECM |
Comes on | DTC stored | SAE Code: P0118 |
| DTC No. | Data List |
|---|---|
| P011511
P011515 |
Coolant Temperature |
If DTC P011511 and/or P011515 is stored, the following symptoms may appear:
Misfire
Combustion noise
Black smoke
White smoke
Lack of power
When DTC P011511 and/or P011515 is stored, check the engine coolant temperature by entering the following menus: Powertrain / Engine / Data List / Coolant Temperature.
| GTS Displayed | Malfunction |
|---|---|
| -40°C (-40°F) | Open circuit |
| 140°C (284°F) or higher | Short circuit |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P011511
P011515 |
Engine switch on (IG) for 0.5 second or more |
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Coolant Temperature.
Read the value.
70 to 90°C (158 to 194°F) with warm engine
| Result | Proceed to |
|---|---|
| -40°C (-40°F) | A |
| 140°C (284°F) or higher | B |
| 70 to 90°C (158 to 194°F) | C |
If there is an open circuit, the GTS indicates -40°C (-40°F).
If there is a short circuit, the GTS indicates 140°C (284°F) or higher.
A
B
C
| *1 | Engine Coolant Temperature Sensor |
| *2 | ECM |
| *a | Front view of wire harness connector
(to Engine Coolant Temperature Sensor) |
Disconnect the engine coolant temperature sensor connector.
Connect terminals 1 and 2 of the engine coolant temperature sensor wire harness side connector.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Coolant Temperature.
Read the value.
140°C (284°F) or higher
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the engine coolant temperature sensor.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the engine coolant temperature sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C24-2 - C149-34 (THW) | Always | Below 1 Ω |
| C24-1 - C149-27 (E2) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
| *1 | Engine Coolant Temperature Sensor |
| *2 | ECM |
Disconnect the engine coolant temperature sensor connector.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Coolant Temperature.
Read the value.
-40°C (-40°F)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the engine coolant temperature sensor.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the engine switch on (IG) for 0.5 second or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the engine coolant temperature sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C24-2 or C149-34 (THW) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT