Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2020.08–2021.06
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P20B912  Reductant Heater "A" Control Circuit High Circuit Short to Battery  P20B914  Reductant Heater "A" Control Circuit Low Circuit Short to Ground or Open  


DESCRIPTION

Refer to DTC P202A12.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>P202A12

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P20B912 Reductant Heater "A" Control Circuit High Circuit Short to Battery When the urea tube with heater is operating, an open or short circuit occurs in the urea tube with heater circuit for 3 seconds or more.
(1 trip detection logic)
·

Open or short in urea tube with heater assembly circuit

·

Urea tube with heater assembly

·

Urea pump control ECU


Comes on DTC stored SAE Code: P20BC
P20B914 Reductant Heater "A" Control Circuit Low Circuit Short to Ground or Open When the urea tube with heater is operating, an open or short circuit occurs in the urea tube with heater circuit for 3 seconds or more.
(1 trip detection logic)
·

Open or short in urea tube with heater assembly circuit

·

Urea tube with heater assembly

·

Urea pump control ECU


Comes on DTC stored SAE Code: P20BB

Related Data List
DTC No. Data List
P20B912
P20B914
Reductant Pipe Heater

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P20B912
P20B914
Reductant Pipe Heater (Active Test)

WIRING DIAGRAM

A357971E26
1.771,1.344 2.302,1.531 0.531,0.188 10 false HTUL 1.74,1.938 2.135,2.135 0.396,0.198 10 false GND1 0.49,2.646 0.802,2.844 0.313,0.198 10 false s2 0.49,2.823 2.938,3.24 2.448,0.417 10 false Urea Tube with Heater Assembly 2.188,2.156 2.344,2.354 0.156,0.198 10 false 2 2.177,1.563 2.49,1.76 0.313,0.198 10 false 1 4.979,1.552 5.292,1.75 0.313,0.198 10 false 20 4.979,2.177 5.292,2.375 0.313,0.198 10 false 32 5.271,1.448 5.729,1.646 0.458,0.198 10 false HTL 5.281,2.063 5.896,2.26 0.615,0.198 10 false EHTL 5.24,2.969 5.552,3.167 0.313,0.198 10 false s4 5.24,3.146 6.896,3.438 1.656,0.292 10 false Urea Pump Control ECU

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT UREA TUBE WITH HEATER ASSEMBLY
a.

Disconnect the urea tube with heater assembly connector.


b.
A179479C04
0.135,0.156 0.448,0.313 0.313,0.156 10 false *a
*a Component without harness connected
(to Urea Tube with Heater Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 6.39 to 7.81 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (UREA TUBE WITH HEATER ASSEMBLY - UREA PUMP CONTROL ECU)

NG

7.REPLACE UREA TUBE WITH HEATER ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (UREA TUBE WITH HEATER ASSEMBLY - UREA PUMP CONTROL ECU)
a.

Disconnect the urea tube with heater assembly connector.


b.

Disconnect the urea pump control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
s2-1 (HTUL) - s4-20 (HTL) Always Below 1 Ω
s2-2 (GND) - s4-32 (EHTL) Always Below 1 Ω
s2-1 (HTUL) or s4-20 (HTL) - Body ground and other terminals Always 10 kΩ or higher
s2-2 (GND) or s4-32 (EHTL) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK DTC OUTPUT

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Clear the DTCs.


d.

Turn the engine switch off and wait for 30 seconds or more.


e.

Turn the engine switch on (IG) and turn the GTS on.


f.

Enter the following menus: Powertrain / Engine / Active Test / Reductant Pipe Heater.


g.

Perform the Active Test.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Read the DTCs.


Result:
Result Proceed to
DTC P20B912 or P20B914 is output A
DTCs is not output B



A

4.REPLACE UREA PUMP CONTROL ECU

B

END

4.REPLACE UREA PUMP CONTROL ECU

Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Clear the DTCs.


d.

Turn the engine switch off and wait for 30 seconds or more.


e.

Turn the engine switch on (IG) and turn the GTS on.


f.

Enter the following menus: Powertrain / Engine / Active Test / Reductant Pipe Heater.


g.

Perform the Active Test.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPLACE UREA TUBE WITH HEATER ASSEMBLY
a.

Replace the urea tube with heater assembly.


Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED