Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type) › 2020.08–2021.06
RM27T0E _56 Audio / Visual / Telematics _053720 AUDIO / VIDEO _0260969 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  B1579  Voice Recognition Microphone Disconnected  


DESCRIPTION

The radio and display receiver assembly, map light assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.

This DTC is stored when a microphone connection detection signal line is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1579 Voice Recognition Microphone Disconnected Microphone signal is lost
·

Map light assembly

·

Telephone microphone assembly

·

Radio and display receiver assembly

·

DCM (telematics transceiver)*

·

Harness or connector



*: w/ Telematics Transceiver


WIRING DIAGRAM

E402555E47
0.656,2.333 2.042,2.708 1.385,0.375 10 false Telephone Microphone Assembly 2.833,2.563 5.594,3.01 2.76,0.448 10 false DCM (Telematics Transceiver) 2.813,2.385 3.344,2.698 0.531,0.313 10 false G187 5.625,2.646 6.875,3.031 1.25,0.385 10 false Radio and Display Receiver Assembly 5.635,2.458 6.042,2.635 0.406,0.177 10 false H93 5.802,0.979 6.24,1.146 0.438,0.167 10 false SNS2 5.479,0.813 5.729,0.979 0.25,0.167 10 false 25 3.229,1.896 3.667,2.063 0.438,0.167 10 false MCI- 2.969,1.74 3.198,1.917 0.229,0.177 10 false 35 1.302,0.938 1.74,1.104 0.438,0.167 10 false SNS2 1.792,0.813 1.958,0.99 0.167,0.177 10 false 1 1.365,1.885 1.802,2.052 0.438,0.167 10 false MIC- 1.813,1.781 1.979,1.958 0.167,0.177 10 false 2 0.146,0.052 4.885,0.656 4.74,0.604 12 false w/ Telematics Transceiver: 0.635,3.219 2.958,3.458 2.323,0.24 10 false Map Light Assembly 2.083,0.771 2.521,0.938 0.438,0.167 10 false SNS2 2.083,1.76 2.521,1.927 0.438,0.167 10 false MCO- 0.667,3.063 1.271,3.25 0.604,0.188 10 false W7 2.646,0.813 3.01,1.083 0.365,0.271 10 false 14 2.646,1.75 3.01,2.021 0.365,0.271 10 false 13 0.656,2.177 2.042,2.552 1.385,0.375 10 false A


E402556E38
0.167,0.073 6.01,0.552 5.844,0.479 12 false w/o Telematics Transceiver: 1.583,0.958 2.042,1.188 0.458,0.229 10 false SNS2 2.052,0.823 2.271,1.01 0.219,0.188 10 false 1 5.448,0.823 5.667,1.01 0.219,0.188 10 false 25 5.771,0.958 6.49,1.25 0.719,0.292 10 false SNS2 2.073,1.844 2.531,2.073 0.458,0.229 10 false 2 5.448,1.823 5.729,2.063 0.281,0.24 10 false 22 5.781,1.969 6.24,2.198 0.458,0.229 10 false MIN- 5.74,2.469 6.198,2.698 0.458,0.229 10 false H93 5.74,2.635 6.969,3.021 1.229,0.385 10 false Radio and Display Receiver Assembly 0.917,3.073 1.375,3.302 0.458,0.229 10 false W7 1.042,2.385 2.469,2.875 1.427,0.49 10 false Telephone Microphone Assembly 0.927,3.229 2.885,3.583 1.958,0.354 10 false Map Light Assembly 2.573,1.854 3.031,2.083 0.458,0.229 10 false MCO- 1.604,1.938 2.063,2.167 0.458,0.229 10 false MIC- 2.604,0.833 3.063,1.063 0.458,0.229 10 false SNS2 3.115,0.833 3.573,1.063 0.458,0.229 10 false 14 3.115,1.844 3.573,2.073 0.458,0.229 10 false 13 1.021,2.24 2.448,2.729 1.427,0.49 10 false A

CAUTION / NOTICE / HINT

NOTICE:

When replacing the DCM (telematics transceiver), make sure to replace it with a new one. (w/ Telematics Transceiver)


HINT:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>PRECAUTION


PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
w/ Telematics Transceiver A
w/o Telematics Transceiver B



A

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)

B

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the H93 radio and display receiver assembly connector.


b.

Disconnect the W7 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H93-25 (SNS2) - W7-14 (SNS2) Always Below 1 Ω
H93-25 (SNS2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (DCM [TELEMATICS TRANSCEIVER] - MAP LIGHT ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (DCM [TELEMATICS TRANSCEIVER] - MAP LIGHT ASSEMBLY)
a.

Disconnect the G187 DCM (telematics transceiver) connector.


b.

Disconnect the W7 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G187-35 (MCI-) - W7-13 (MCO-) Always Below 1 Ω
G187-35 (MCI-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK DCM (TELEMATICS TRANSCEIVER) (MCI-)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK DCM (TELEMATICS TRANSCEIVER) (MCI-)
a.
E364292C23
1.479,0.479 2.094,0.75 0.615,0.271 0.833,2.813 1.021,2.813 1.021,2.813 1.229,2.063 true 1.635,0.531 2.01,0.719 0.375,0.188 10 false G187 0.448,2.75 0.906,2.948 0.458,0.198 10 false MCI- 0.146,0.156 0.458,0.354 0.313,0.198 10 false *a
*a Component with harness connected
(DCM [Telematics Transceiver])


Remove the DCM (telematics transceiver) with the connector(s) still connected.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G187-35 (MCI-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.INSPECT MAP LIGHT ASSEMBLY

NG

REPLACE DCM (TELEMATICS TRANSCEIVER)

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the H93 radio and display receiver assembly connector.


b.

Disconnect the W7 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H93-25 (SNS2) - W7-14 (SNS2) Always Below 1 Ω
H93-22 (MIN-) - W7-13 (MCO-) Always Below 1 Ω
H93-25 (SNS2) - Body ground Always 10 kΩ or higher
H93-22 (MIN-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT MAP LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>ROOM LIGHT(for Front)>REMOVAL


b.
E140936C40
1.021,1.344 1.302,0.75 1.302,0.75 1.479,0.75 true 0.885,1.365 0.74,0.76 0.74,0.76 0.594,0.76 true 0.167,0.104 0.479,0.302 0.313,0.198 10 false *a 1.542,0.646 2.177,0.896 0.635,0.25 10 false MCO- 0.177,0.677 0.813,0.927 0.635,0.25 10 false SNS2
*a Component without harness connected
(Map Light Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
13 (SNS2) - 14 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

7.INSPECT MAP LIGHT ASSEMBLY
7.INSPECT MAP LIGHT ASSEMBLY
a.
E355979C03
0.094,0.854 0.479,1.135 0.385,0.281 0.344,2.396 0.729,2.677 0.385,0.281 0.948,0.979 0.823,0.198 0.823,0.198 1,0.198 true 0.438,0.49 0.563,0.49 0.563,0.49 0.813,0.979 true 1.448,2.708 1.521,3.24 1.521,3.24 1.698,3.24 true 1.188,2.698 1,3.208 1,3.208 0.823,3.208 true 0.188,0.906 0.458,1.104 0.271,0.198 10 false W7 0.479,2.458 0.688,2.677 0.208,0.219 10 false A 1.063,0.115 1.542,0.333 0.479,0.219 10 false MCO- 1.76,3.156 2.24,3.375 0.479,0.219 10 false MIC- 0.042,0.417 0.521,0.635 0.479,0.219 10 false SNS2 0.427,3.135 0.906,3.354 0.479,0.219 10 false SNS2 0.177,1.885 0.385,2.104 0.208,0.219 10 false *b 0.083,0.063 0.292,0.281 0.208,0.219 10 false *a
*a Component without harness connected
(Map Light Assembly)
*b Component without harness connected
(Map Light Assembly [Telephone Microphone Assembly Side])


Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>ROOM LIGHT(for Front)>REMOVAL


b.

Disconnect the telephone microphone assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W7-14 (SNS2) - A-1 (SNS2) Always Below 1 Ω
W7-13 (MCO-) - A-2 (MIC-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG