Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type) › from 2020.08
RM27T0E _56 Audio / Visual / Telematics _053720 AUDIO / VIDEO _0260969 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  C1622  Back Camera Disconnected  


DESCRIPTION

This DTC is stored if the radio and display receiver assembly judges that the signals or signal lines between the rear television camera assembly*1 or parking assist ECU*2 and the radio and display receiver assembly are not normal as a result of its self check.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1622 Back Camera Disconnected Open or short in the rear television camera assembly signal circuit
·

Harness or connector

·

Rear television camera assembly*1

·

Multi-terrain Monitor System*2

·

Radio and display receiver assembly



*1: w/ Rear View Monitor System

*2: w/ Multi-terrain Monitor System


WIRING DIAGRAM

E450948E01
0.625,2.969 3.417,3.188 2.792,0.219 10 false Radio and Display Receiver Assembly 0.635,2.781 1.021,2.979 0.385,0.198 10 false H93 1.781,2.531 2.333,2.74 0.552,0.208 10 false CGND 1.938,2.052 2.323,2.25 0.385,0.198 10 false V- 1.938,1.646 2.323,1.844 0.385,0.198 10 false V+ 1.885,1.219 2.271,1.417 0.385,0.198 10 false CA+ 2.292,1.125 2.677,1.323 0.385,0.198 10 false 30 2.271,1.938 2.656,2.135 0.385,0.198 10 false 29 2.292,1.479 2.677,1.677 0.385,0.198 10 false 28 2.281,2.396 2.667,2.594 0.385,0.198 10 false 27 4.438,2.802 5.604,3 1.167,0.198 10 false X9*2, v2*3 4.427,3 6.573,3.281 2.146,0.281 10 false Rear Television Camera Assembly 5.167,1.188 5.552,1.385 0.385,0.198 10 false CB+ 5.198,1.635 5.583,1.833 0.385,0.198 10 false CV+ 5.167,2.083 5.552,2.281 0.385,0.198 10 false CV- 5.167,2.542 5.76,2.813 0.594,0.271 10 false CGND 4.958,1.104 5.344,1.302 0.385,0.198 10 false 6 4.917,1.49 5.302,1.688 0.385,0.198 10 false 3 4.917,1.885 5.302,2.083 0.385,0.198 10 false 2 4.927,2.396 5.313,2.594 0.385,0.198 10 false 5 3.552,2.427 3.938,2.625 0.385,0.198 10 false *1 0.125,0.073 6.177,0.313 6.052,0.24 12 false w/ Rear View Monitor System: 0.823,3.396 1.667,3.604 0.844,0.208 10 false *1: Shielded 3.938,3.417 5.385,3.656 1.448,0.24 10 false *3: w/ Tire Carrier 2.396,3.417 4.135,3.667 1.74,0.25 10 false *2: w/o Tire Carrier

E450951E01
5,1.385 5.458,1.583 0.458,0.198 10 false NS+ 5,1.75 5.458,1.948 0.458,0.198 10 false NS- 5,2.208 5.458,2.406 0.458,0.198 10 false NSG 1.969,1.333 2.427,1.531 0.458,0.198 10 false V+ 1.99,1.75 2.448,1.948 0.458,0.198 10 false V- 0.625,2.781 3.354,3.042 2.729,0.26 10 false Radio and Display Receiver Assembly 4.729,2.802 6.25,3.208 1.521,0.406 10 false Parking Assist ECU 2.302,1.229 2.76,1.427 0.458,0.198 10 false 28 2.271,1.656 2.729,1.854 0.458,0.198 10 false 29 0.302,3.302 1.552,3.583 1.25,0.281 10 false *: Shielded 3.542,2.156 4,2.354 0.458,0.198 10 false * 4.688,1.635 5.146,1.833 0.458,0.198 10 false 17 4.719,1.229 5.177,1.427 0.458,0.198 10 false 16 4.698,2.073 5.156,2.271 0.458,0.198 10 false 18 0.635,2.604 1.094,2.802 0.458,0.198 10 false H93 0.25,0.135 6.302,0.375 6.052,0.24 12 false w/ Multi-Terrain Monitor System: 4.719,2.604 5.177,2.802 0.458,0.198 10 false I7 1.76,2.198 2.219,2.396 0.458,0.198 10 false CGND 2.292,2.063 2.75,2.26 0.458,0.198 10 false 27

PROCEDURE

1.CHECK MODEL
a.

Choose the model to be inspected.

Result:
Result Proceed to
w/ Rear View Monitor System A
w/ Multi-terrain Monitor System B




A

2.CHECK HARNESS AND CONNECTOR (REAR TELEVISION CAMERA ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)

B

5.CHECK DTC (MULTI-TERRAIN MONITOR SYSTEM)
2.CHECK HARNESS AND CONNECTOR (REAR TELEVISION CAMERA ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the X9*1 or v2*2 rear television camera assembly connector.

*1: w/o Tire Carrier

*2: w/ Tire Carrier



b.

Disconnect the H93 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Tire Carrier
Tester Connection Condition Specified Condition
X9-6 (CB+) - H93-30 (CA+) Always Below 1 Ω
X9-3 (CV+) - H93-28 (V+) Always Below 1 Ω
X9-2 (CV-) - H93-29 (V-) Always Below 1 Ω
X9-5 (CGND) - H93-27 (CGND) Always Below 1 Ω
X9-6 (CB+) - Body ground Always 10 kΩ or higher
X9-3 (CV+) - Body ground Always 10 kΩ or higher
X9-2 (CV-) - Body ground Always 10 kΩ or higher
X9-5 (CGND) - Body ground Always 10 kΩ or higher

w/ Tire Carrier
Tester Connection Condition Specified Condition
v2-6 (CB+) - H93-30 (CA+) Always Below 1 Ω
v2-3 (CV+) - H93-28 (V+) Always Below 1 Ω
v2-2 (CV-) - H93-29 (V-) Always Below 1 Ω
v2-5 (CGND) - P42-27 (CGND) Always Below 1 Ω
v2-6 (CB+) - Body ground Always 10 kΩ or higher
v2-3 (CV+) - Body ground Always 10 kΩ or higher
v2-2 (CV-) - Body ground Always 10 kΩ or higher
v2-5 (CGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK RADIO AND DISPLAY ASSEMBLY (CA+, CGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK RADIO AND DISPLAY ASSEMBLY (CA+, CGND)
a.
E402607C36
1.583,0.156 1.969,0.458 0.385,0.302 0.583,1.646 0.771,1.646 0.771,1.646 0.969,1.24 true 0.969,1.844 1.156,1.844 1.156,1.844 1.417,1.25 true 1.677,0.229 2.135,0.427 0.458,0.198 10 false H93 0.24,0.135 0.698,0.333 0.458,0.198 10 false *a 0.25,1.542 0.708,1.74 0.458,0.198 10 false CA+ 0.542,1.75 1.052,1.948 0.51,0.198 10 false CGND
*a Component with harness connected
(Radio and Display Receiver Assembly)


Remove the radio and display receiver assembly with the connector still connected.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H93-30 (CA+) - H93-27 (CGND) Ignition switch ACC 5.5 to 7.05 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H93-27 (CGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK REAR TELEVISION CAMERA ASSEMBLY

NG

4.CHECK REAR TELEVISION CAMERA ASSEMBLY
E402606C33
0.958,1.073 1.313,1.344 0.354,0.271 2.698,2.885 2.875,2.885 2.875,2.885 3.135,2.25 true 5,2.792 5.177,2.792 5.177,2.792 5.438,2.156 true 3.208,2.167 3.375,2.917 3.375,2.917 3.531,2.917 true 5.542,2.104 5.708,2.854 5.708,2.854 5.865,2.854 true 0.344,2.573 0.521,2.573 0.521,2.573 0.635,1.969 true 0.74,1.958 0.865,2.823 0.865,2.823 1.021,2.823 true 0.177,0.99 0.49,1.188 0.313,0.198 10 false *a 2.635,0.979 2.948,1.177 0.313,0.198 10 false *b 4.948,0.927 5.26,1.125 0.313,0.198 10 false *c 2.531,2.792 2.844,2.99 0.313,0.198 10 false *d 3.583,2.813 3.896,3.01 0.313,0.198 10 false *e 4.823,2.698 5.135,2.896 0.313,0.198 10 false *d 5.917,2.76 6.229,2.958 0.313,0.198 10 false *e 2.448,1.792 2.906,2.031 0.458,0.24 10 false GND 4.75,1.813 5.208,2.052 0.458,0.24 10 false GND 1.073,2.75 1.385,2.948 0.313,0.198 10 false V+ 0.135,2.479 0.448,2.677 0.313,0.198 10 false V- 1.01,1.125 1.323,1.323 0.313,0.198 10 false H93
*a Component with harness connected *b Waveform 1
*c Waveform 2 *d Synchronization Signal
*e Video Waveform - -


a.

Remove the radio and display receiver assembly with the connector still connected.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL


b.

Check the waveform of the rear television camera assembly using an oscilloscope.

Item Content
Measurement terminal H93-28 (V+) - H93-29 (V-)
Measurement setting 200 mV/DIV., 50 μsec./DIV.
Condition Waveform 1: Ignition switch ON, shift position in R, camera lens is not covered, displaying an image.
Waveform 2: Ignition switch ON, shift position in R, camera lens is covered, blacking out the screen.

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the ignition is ACC.



OK:

Waveform is as shown in the illustration.



Result:
Proceed to
OK
NG



OK

NG

5.CHECK DTC (MULTI-TERRAIN MONITOR SYSTEM)

b.

Recheck for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>DTC CHECK / CLEAR

OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - RADIO AND DISPLAY RECEIVER ASSEMBLY)

NG

6.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the I7 parking assist ECU connector.


b.

Disconnect the H93 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I7-16 (NS+) - H93-28 (V+) Always Below 1 Ω
I7-17 (NS-) - H93-29 (V-) Always Below 1 Ω
I7-18 (NSG) - H93-27 (CGND) Always Below 1 Ω
I7-16 (NS+) - Body ground Always 10 kΩ or higher
I7-17 (NS-) - Body ground Always 10 kΩ or higher
I7-18 (NSG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK PARKING ASSIST ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK PARKING ASSIST ECU
E402606C34
0.958,1.073 1.313,1.344 0.354,0.271 2.698,2.885 2.875,2.885 2.875,2.885 3.135,2.25 true 5,2.792 5.177,2.792 5.177,2.792 5.438,2.156 true 3.208,2.167 3.375,2.917 3.375,2.917 3.531,2.917 true 5.542,2.104 5.708,2.854 5.708,2.854 5.865,2.854 true 0.344,2.573 0.521,2.573 0.521,2.573 0.635,1.969 true 0.74,1.958 0.865,2.823 0.865,2.823 1.021,2.823 true 0.177,0.99 0.49,1.188 0.313,0.198 10 false *a 2.635,0.979 2.948,1.177 0.313,0.198 10 false *b 4.948,0.927 5.26,1.125 0.313,0.198 10 false *c 2.531,2.792 2.844,2.99 0.313,0.198 10 false *d 3.583,2.813 3.896,3.01 0.313,0.198 10 false *e 4.823,2.698 5.135,2.896 0.313,0.198 10 false *d 5.917,2.76 6.229,2.958 0.313,0.198 10 false *e 2.448,1.792 2.906,2.031 0.458,0.24 10 false GND 4.75,1.813 5.208,2.052 0.458,0.24 10 false GND 1.073,2.75 1.385,2.948 0.313,0.198 10 false V+ 0.135,2.479 0.448,2.677 0.313,0.198 10 false V- 1.042,1.125 1.354,1.323 0.313,0.198 10 false H93
*a Component with harness connected
(Radio and Display Receiver Assembly)
*b Waveform 1 (camera lens not covered, displaying an image)
*c Waveform 2 (camera lens covered, blacking out the screen) *d Synchronization Signal
*e Video Waveform - -


a.

Remove the radio and display receiver assembly with the connector still connected.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL


b.

Check the waveform of the parking assist ECU using an oscilloscope.

Item Content
Measurement terminal H93-28 (V+) - H93-29 (V-)
Measurement setting 200 mV/DIV., 50 μsec./DIV.
Condition Waveform 1: Ignition switch ON, shift position in R, camera lens is not covered, displaying an image.
Waveform 2: Ignition switch ON, shift position in R, camera lens is covered, blacking out the screen.

HINT:
·

The video waveform changes according to the image sent by the parking assist ECU.

·

The video waveform is constantly output when the ignition switch is ACC.



OK:

Waveform is similar to that shown in the illustration.



Result:
Proceed to
OK
NG



OK

NG