Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › from 2020.08
RM27T0E _51 Engine / Hybrid System _091546 STOP AND START _0437376 STOP AND START SYSTEM C

STOP AND START  STOP AND START SYSTEM  P061519  Starter Relay Circuit Current Above Threshold  


DESCRIPTION

When the engine is started by stop and start control, the engine stop and start ECU controls the starter assembly by activating the ST relay (for starter pinion operation) via voltage from terminal STA and then, using its built-in starter delay circuit, activating the ST NO. 2 relay (for starter motor operation) via voltage from terminal STA2.

If overcurrent is detected in the starter relay circuit, the engine stop and start ECU stores DTC P061519 and blinks the stop and start cancel indicator.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory Note
P061519 Starter Relay Circuit Current Above Threshold Both of the following conditions are met for 1 second (1 trip detection logic):
·

Engine switch on (IG)

·

Overcurrent to ST relay or ST NO. 2 relay is detected.


·

Wire harness or connector

·

ST relay

·

ST NO. 2 relay

·

Engine stop and start ECU


Blinks DTC stored SAE Code: P0617

CONFIRMATION DRIVING PATTERN

HINT:

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.


CONFIRMATION AFTER TROUBLESHOOTING


HINT:
·

If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.

In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item "Status of Battery Charge Control" changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the battery fluid temperature at 11°C (52°F) or higher, the refresh charge will be completed.)

·

If the GTS is not available and the Data List item "Status of Battery Charge Control" cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

·

After the refresh charge completes, turn the engine switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.

·

Allow the engine to idle for 3 minutes after it is warmed up and check that the engine idle speed is within 50 rpm of the target idle speed.



a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Clear the DTCs.


d.

Start the engine and warm it up.


e.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



f.

Depress the brake pedal and stop the vehicle.


g.

Keep the engine stopped by stop and start control for 1 second or more. (Keep the shift lever in D.)


h.

Release the brake pedal with the shift lever in D to start the engine.


i.

Check that DTCs are not output.



STOP AND START SYSTEM OPERATION CHECK


Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>OPERATION CHECK


WIRING DIAGRAM

A475033E01
0.188,2.354 1.271,2.885 1.083,0.531 10 false Certification ECU (Smart Key ECU Assembly) 0.625,1.667 1.021,1.927 0.396,0.26 10 false STAR 1.115,1.531 1.427,1.729 0.313,0.198 10 false 10 0.698,0.969 1.156,1.167 0.458,0.198 10 false STA 1.115,0.833 1.427,1.031 0.313,0.198 10 false 12 2.708,2.167 4.031,2.969 1.323,0.802 10 false Park/Neutral Position Switch Assembly 2.063,1.906 2.219,2.104 0.156,0.198 10 false 5 2.583,2.906 2.74,3.104 0.156,0.198 10 false 4 5.323,3.115 6.375,3.656 1.052,0.542 10 false Engine Stop and Start ECU 5.406,0.969 5.865,1.167 0.458,0.198 10 false STA 5.406,1.344 5.865,1.542 0.458,0.198 10 false BIN2 5.396,1.719 6.01,1.917 0.615,0.198 10 false STA2 5.417,2.688 5.875,2.885 0.458,0.198 10 false CLL 5.406,0.448 5.865,0.646 0.458,0.198 10 false BIN1 5.385,2.167 5.875,2.365 0.49,0.198 10 false DGND 5.01,0.458 5.469,0.656 0.458,0.198 10 false G312 5.125,0.271 5.281,0.469 0.156,0.198 10 false 3 4.99,1.344 5.448,1.542 0.458,0.198 10 false G312 5.125,1.167 5.281,1.365 0.156,0.198 10 false 1 5,0.969 5.458,1.167 0.458,0.198 10 false G313 5.115,0.771 5.427,0.969 0.313,0.198 10 false 21 5,1.729 5.458,1.927 0.458,0.198 10 false G313 5.125,1.542 5.438,1.74 0.313,0.198 10 false 23 4.99,2.677 5.448,2.875 0.458,0.198 10 false G313 5.104,2.479 5.417,2.677 0.313,0.198 10 false 17 4.99,2.167 5.448,2.365 0.458,0.198 10 false G313 5.146,1.969 5.302,2.167 0.156,0.198 10 false 6 5.833,1.479 6.448,1.677 0.615,0.198 10 false CANH 6.26,1.469 6.719,1.667 0.458,0.198 10 false G314 6.354,1.271 6.667,1.469 0.313,0.198 10 false 13 5.833,1.958 6.448,2.156 0.615,0.198 10 false CANL 6.26,1.948 6.719,2.146 0.458,0.198 10 false G314 6.354,1.76 6.667,1.958 0.313,0.198 10 false 14 2.542,4 3.292,4.208 0.75,0.208 10 false BBC NO. 3 3.25,4.927 4.083,5.146 0.833,0.219 10 false BBC NO. 2 5.688,6.031 6.146,6.229 0.458,0.198 10 false ECM 5.844,4.667 6.458,4.865 0.615,0.198 10 false CANL 5.833,5.365 6.448,5.563 0.615,0.198 10 false CANH 1.448,7.177 1.604,7.375 0.156,0.198 10 false B 1.938,7.177 2.396,7.375 0.458,0.198 10 false SL1 2.688,7.677 3.146,7.875 0.458,0.198 10 false SL2 2.635,7.167 2.927,7.385 0.292,0.219 10 false ST 2.021,4.427 3.25,4.625 1.229,0.198 10 false ST NO. 2 1.198,5.396 2.427,5.594 1.229,0.198 10 false ST 1.573,5.563 1.729,5.76 0.156,0.198 10 false 2 1.938,5.573 2.094,5.771 0.156,0.198 10 false 5 0.5,7.667 1.573,7.865 1.073,0.198 10 false Battery 1.396,8.146 3.844,8.344 2.448,0.198 10 false Starter Assembly 3.615,8.458 5.458,8.677 1.844,0.219 10 false : CAN Communication Line 4.75,6.781 5.979,6.979 1.229,0.198 10 false ST NO. 2 1.948,6.323 2.104,6.521 0.156,0.198 10 false 3 2.302,5.927 3.219,6.156 0.917,0.229 10 false ST 1.542,6.302 1.698,6.5 0.156,0.198 10 false 1 4.385,6.396 4.542,6.594 0.156,0.198 10 false 2 4.01,6.396 4.167,6.594 0.156,0.198 10 false 5 4.031,7.125 4.188,7.323 0.156,0.198 10 false 3 4.365,7.135 4.521,7.333 0.156,0.198 10 false 1 5.521,4.854 5.979,5.052 0.458,0.198 10 false NSW 5.521,5.156 5.979,5.354 0.458,0.198 10 false STA 2.969,3.698 3.125,3.896 0.156,0.198 10 false 2 2.563,3.708 2.719,3.906 0.156,0.198 10 false 1 3.302,4.635 3.458,4.833 0.156,0.198 10 false 1 3.688,4.625 3.844,4.823 0.156,0.198 10 false 2 5.833,0.375 6.448,0.573 0.615,0.198 10 false GND1 6.26,0.375 6.719,0.573 0.458,0.198 10 false G312 6.385,0.188 6.542,0.385 0.156,0.198 10 false 8 5.833,0.823 6.448,1.021 0.615,0.198 10 false GND2 6.385,0.646 6.542,0.844 0.156,0.198 10 false 2 6.271,0.833 6.729,1.031 0.458,0.198 10 false G312 6.302,4.479 6.615,4.677 0.313,0.198 10 false 28 6.302,5.167 6.615,5.365 0.313,0.198 10 false 17 5.26,4.729 5.573,4.927 0.313,0.198 10 false 11 5.271,5.052 5.583,5.25 0.313,0.198 10 false 22 5.51,5.833 5.969,6.031 0.458,0.198 10 false G184 2.708,1.958 3.167,2.156 0.458,0.198 10 false C159 1.375,6.938 1.688,7.135 0.313,0.198 10 false D13 1.167,6.906 1.323,7.104 0.156,0.198 10 false 1 0.177,2.146 0.635,2.344 0.458,0.198 10 false G213 1.948,6.938 2.406,7.135 0.458,0.198 10 false D14 1.75,6.906 1.906,7.104 0.156,0.198 10 false 1 2.563,6.948 3.021,7.146 0.458,0.198 10 false D15 2.365,6.917 2.521,7.115 0.156,0.198 10 false 1 3.063,7.677 3.521,7.875 0.458,0.198 10 false D14 3.146,7.479 3.302,7.677 0.156,0.198 10 false 2 2.188,2.167 2.344,2.365 0.156,0.198 10 false L 2.458,2.167 2.615,2.365 0.156,0.198 10 false B 0.469,3.979 1.542,4.177 1.073,0.198 10 false 125A FL 0.438,4.479 0.802,4.854 0.365,0.375 10 false 250A FL

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and total number of engine starts and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU, airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU assembly, perform learning of the external backup boost converter (eco run vehicle converter assembly).

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When the engine stop and start ECU or electromagnetic oil pump is replaced, check the electromagnetic oil pump.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION



HINT:
·

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>FREEZE FRAME DATA

·

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BBC FUSE)
a.

Disconnect the engine stop and start ECU connector.


b.

Remove the BBC NO. 2 and BBC NO. 3 fuses from the No. 7 relay block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G312-1 (BIN2) - BBC NO. 3 fuse terminal 2 Always Below 1 Ω
G312-3 (BIN1) - BBC NO. 2 fuse terminal 2 Always Below 1 Ω
G312-1 (BIN2) - Body ground Always 10 kΩ or higher
G312-3 (BIN1) - Body ground Always 10 kΩ or higher
BBC NO. 3 fuse terminal 2 - Body ground Always 10 kΩ or higher
BBC NO. 2 fuse terminal 2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST, ST NO. 2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST, ST NO. 2 RELAY)
a.

Disconnect the engine stop and start ECU connectors.


b.

Remove the ST and ST NO. 2 relays from the engine room relay block and junction block assembly.


c.

Remove the BBC NO. 2 and BBC NO. 3 fuses from the No. 7 relay block assembly.


d.

Disconnect the certification ECU (smart key ECU assembly) connector.


e.

Disconnect the park/neutral position switch assembly connector.


f.

Disconnect the ECM connector.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G313-21 (STA) - ST relay terminal 2 Always Below 1 Ω
G313-23 (STA2) - ST NO. 2 relay terminal 2 Always Below 1 Ω
G313-21 (STA) - Body ground Always 10 kΩ or higher
ST relay terminal 2 - Body ground Always 10 kΩ or higher
G313-23 (STA2) - Body ground Always 10 kΩ or higher
ST NO. 2 relay terminal 2 - Body ground Always 10 kΩ or higher
G312-1 (BIN2) - G313-21 (STA) Always 10 kΩ or higher
G312-3 (BIN1) - G313-21 (STA) Always 10 kΩ or higher
G312-1 (BIN2) - G313-23 (STA2) Always 10 kΩ or higher
G312-3 (BIN1) - G313-23 (STA2) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK ENGINE STOP AND START ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK ENGINE STOP AND START ECU
a.

Disconnect the engine stop and start ECU connector.

B412468C61
3.167,0.24 3.688,0.469 0.521,0.229 0.396,0.146 0.76,0.396 0.365,0.25 10 false *a 3.24,0.26 3.656,0.5 0.417,0.24 10 false G313
*a Component without harness connected
(Engine Stop and Start ECU)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G313-21 (STA) - G313-6 (DGND) Always 10 kΩ or higher
G313-23 (STA2) - G313-6 (DGND) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT RELAY (ST, ST NO. 2 RELAY)

NG

4.INSPECT RELAY (ST, ST NO. 2 RELAY)


Result:
Proceed to
OK
NG



OK

NG

REPLACE RELAY (ST, ST NO. 2 RELAY)