Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › from 2020.08
RM27T0E _51 Engine / Hybrid System _091546 STOP AND START _0437376 STOP AND START SYSTEM J

STOP AND START  STOP AND START SYSTEM  Stop and Start Cancel Switch Circuit  


DESCRIPTION

Stop and start control can be disabled by pressing the stop and start system cancel switch (eco run cancel switch assembly). The stop and start system cancel switch (eco run cancel switch assembly) is a momentary-type switch that switches between on and off when the switch is pressed. While stop and start control is disabled, the stop and start cancel indicator light is illuminated to inform the driver.

WIRING DIAGRAM

A348170E27
1.76,1.469 2.219,1.667 0.458,0.198 10 false G311 2.063,0.865 2.292,1.104 0.229,0.24 10 false 3 3.521,0.875 4.344,1.063 0.823,0.188 10 false 4 1.76,1.625 4.115,2.073 2.354,0.448 10 false Stop and Start System Cancel Switch (Eco run Cancel Switch Assembly) 5.469,0.938 5.927,1.135 0.458,0.198 10 false 5 5.625,1.542 6.083,1.74 0.458,0.198 10 false G314 5.625,1.698 6.698,2.219 1.073,0.521 10 false Engine Stop and Start ECU 5.667,1.052 6.125,1.25 0.458,0.198 10 false ECAN 3.146,0.875 3.604,1.073 0.458,0.198 10 false ECU 2.271,0.854 2.427,1.052 0.156,0.198 10 false E

PROCEDURE

1.READ VALUE USING GTS (CANCEL SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Data List / Cancel Switch.


e.

Read the value when the stop and start system cancel switch (eco run cancel switch assembly) is pressed.

OK:
Tester Display Condition Normal Condition
Cancel Switch Stop and start system cancel switch (eco run cancel switch assembly) is pressed ON
Stop and start system cancel switch (eco run cancel switch assembly) is not pressed OFF



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT STOP AND START SYSTEM CANCEL SWITCH (ECO RUN CANCEL SWITCH ASSEMBLY)
2.INSPECT STOP AND START SYSTEM CANCEL SWITCH (ECO RUN CANCEL SWITCH ASSEMBLY)
a.

Inspect the stop and start system cancel switch (eco run cancel switch assembly).

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM CANCEL SWITCH ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (STOP AND START SYSTEM CANCEL SWITCH (ECO RUN CANCEL SWITCH ASSEMBLY) - BODY GROUND)

NG

REPLACE STOP AND START SYSTEM CANCEL SWITCH (ECO RUN CANCEL SWITCH ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (STOP AND START SYSTEM CANCEL SWITCH (ECO RUN CANCEL SWITCH ASSEMBLY) - BODY GROUND)
a.

Disconnect the stop and start system cancel switch (eco run cancel switch assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G311-3 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - STOP AND START SYSTEM CANCEL SWITCH (ECO RUN CANCEL SWITCH ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - STOP AND START SYSTEM CANCEL SWITCH (ECO RUN CANCEL SWITCH ASSEMBLY))
a.

Disconnect the engine stop and start ECU connector.


b.

Disconnect the stop and start system cancel switch (eco run cancel switch assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G314-5 (ECAN) - G311-4 (ECU) Always Below 1 Ω
G314-5 (ECAN) - Body ground Always 10 kΩ or higher
G311-4 (ECU) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR