Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM › from 2020.08
RM27T0E _58 Vehicle Interior _091549 PRE-COLLISION _0438246 PRE-COLLISION SYSTEM C

PRE-COLLISION  PRE-COLLISION SYSTEM  U023A87  Lost Communication with Image Processing Module "A"  


DESCRIPTION

The forward recognition camera is connected to the skid control ECU (master cylinder solenoid) via the CAN communication line. When the skid control ECU (master cylinder solenoid) receives a forward recognition camera communication malfunction signal, the forward recognition camera outputs U023A87.

DTC No. Detection Item DTC Detection Condition Trouble Area
U023A87 Lost Communication with Image Processing Module "A" Once 2 seconds elapse after turning the ignition switch to ON, the skid control ECU (master cylinder solenoid) receives a forward recognition camera communication malfunction signal from the skid control ECU (master cylinder solenoid) for approximately 3 seconds or more.
·

Vehicle stability control system

·

Forward recognition camera



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

When the forward recognition camera is replaced with a new one, make sure to perform beam axis adjustment for the forward recognition camera and clear the vehicle control history for each system.

HINT:

Forward recognition camera adjustment can be performed by using either "One Time Recognition" or "Sequential Recognition".

One Time Recognition:

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (ONE TIME RECOGNITION)

Sequential Recognition:

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)




PROCEDURE

1.CHECK VEHICLE STABILITY CONTROL SYSTEM
a.

Check the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>DTC CHECK / CLEAR

HINT:

If U023A87 is output in the pre-collision system, vehicle stability control system DTCs may also have been output. Check the electronically controlled brake system first.


OK:

Vehicle stability control system DTCs are not output.



Result:
Proceed to
OK
NG



OK

2.TEST MODE INSPECTION (VEHICLE STABILITY CONTROL SYSTEM)

NG

2.TEST MODE INSPECTION (VEHICLE STABILITY CONTROL SYSTEM)
a.

When using the GTS:

i.

Place the vehicle on a level surface with an inclination of less than 1%.


ii.

Turn the ignition switch off.


iii.

Connect the GTS to the DLC3.


iv.

Turn the ignition switch to ON.


v.

Turn the GTS on.


vi.

Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Signal Check.


vii.

Check that the ABS warning light and slip indicator light blink at 0.125 second intervals (0.125 seconds on and 0.125 seconds off).


viii.

Start the engine.



b.

End of Signal Check

i.

If the signal check is completed, the ABS warning light and slip indicator light blink (0.125 seconds on and 0.125 seconds off) when the vehicle is stopped and goes off while driving the vehicle.

NOTICE:

If the signal check is not completed, the ABS warning light blinks while driving and the ABS does not operate.



ii.

Turn the ignition switch off and disconnect the GTS.



Result:
Proceed to
NEXT



NEXT

3.CHECK FOR DTC
3.CHECK FOR DTC

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



c.

Recheck for DTCs and check that no DTCs are output.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

OK:

DTC U023A87 is not output.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE FORWARD RECOGNITION CAMERA