The forward recognition camera receives vehicle information (Conv/HV/EV) from the ECM via the CAN communication line.
When the forward recognition camera is unable to determine the vehicle information (Conv/HV/EV) from the vehicle information (Conv/HV/EV) sent from the ECM, the forward recognition camera outputs U030051.
When the vehicle information (Conv/HV/EV) sent from the ECM does not match the vehicle information stored by the forward recognition camera, the forward recognition camera outputs U030057.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| U030051 | Internal Control Module Software Incompatibility Not Programmed | Once 3 seconds elapse after turning the ignition switch to ON, the system is unable to determine the vehicle information (Conv/HV/EV) sent from the ECM and vehicle information (Conv/HV/EV) sent from the forward recognition camera for approximately 3 seconds or more | ·
SFI system ·
ECD system ·
Forward recognition camera |
| U030057 | Internal Control Module Software Incompatibility Invalid / Incompatible Software Component | Once 3 seconds elapse after turning the ignition switch to ON, the vehicle information (Conv/HV/EV) sent from the ECM does not match the vehicle information stored by the forward recognition camera for approximately 1 second or more | ·
SFI system ·
ECD system ·
Forward recognition camera |
When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
When the forward recognition camera is replaced with a new one, make sure to perform beam axis adjustment for the forward recognition camera and clear the vehicle control history for each system.
Forward recognition camera adjustment can be performed by using either "One Time Recognition" or "Sequential Recognition".
One Time Recognition:
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (ONE TIME RECOGNITION)
Sequential Recognition:
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)
When replacing the ECM, refer to Service Bulletin.
Check for DTCs.
for 2TR-FE:
Click hereEngine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR
for 1GR-FE:
Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR
for 1GD-FTV:
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR
for 1GD-FTV wthe DPF:
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DTC CHECK / CLEAR
for 1GD-FTV wthe Urea SCR System:
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>DTC CHECK / CLEAR
If the pre-collision system outputs U030051 or U030057, SFI system DTCs may also have been output. Check the SFI system first.
SFI system DTCs are not output.
| Result | Proceed to |
|---|---|
| SFI or ECD system DTCs are not output | A |
| SFI system DTCs are output | B |
| ECD system DTCs are output | C |
A
B
for 2TR-FE:
Click hereEngine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
for 1GR-FE:
Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
C
for 1GD-FTV:
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
for 1GD-FTV wthe DPF:
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DIAGNOSTIC TROUBLE CODE CHART
for 1GD-FTV wthe Urea SCR System:
Using the GTS, perform the Health Check.
Check for DTCs.
ECUs other than the forward recognition camera do not output specification information mismatch DTCs related to the ECM.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for 2TR-FE:
Click hereEngine / Hybrid System>2TR-FE (ENGINE CONTROL)>ECM>REMOVAL
for 1GR-FE:
Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>ECM>REMOVAL
for 1GD-FTV:
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
Using the GTS, read the Data List.
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item / Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Vehicle Information (Conv/HV/EV) | Vehicle information (Conv/HV/EV) / Unknown, Conv, HV/EV | Unknown: Vehicle information not confirmed
Conv: Conventional HV/EV: Hybrid vehicle |
- |
When the specification stored by the forward recognition camera and the vehicle specification do not match, there is a malfunction in the specification information stored by the forward recognition camera. Therefore, replace the forward recognition camera.
When the specification stored by the forward recognition camera and the vehicle specification match, an ECM with different specifications may be installed. Therefore, replace the ECM.
| Result | Proceed to |
|---|---|
| Specification stored by the forward recognition camera and vehicle specification do not match | A |
| "Unknown" is displayed | |
| Specification stored by the forward recognition camera and vehicle specification match | B |
A
B
for 2TR-FE:
Click hereEngine / Hybrid System>2TR-FE (ENGINE CONTROL)>ECM>REMOVAL
for 1GR-FE:
Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>ECM>REMOVAL
for 1GD-FTV:
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL