Home › Audio / Visual / Telematics › AUDIO / VIDEO › REAR SEAT ENTERTAINMENT SYSTEM › from 2020.08
RM27T0E _56 Audio / Visual / Telematics _053720 AUDIO / VIDEO _0260968 REAR SEAT ENTERTAINMENT SYSTEM J

AUDIO / VIDEO  REAR SEAT ENTERTAINMENT SYSTEM  Mute Signal Circuit between Radio Receiver and Television Display Assembly  


DESCRIPTION

The radio and display receiver assembly controls the volume according to the mute signal from the television display assembly.

The mute signal is sent to reduce noise and popping sounds, such as those generated when switching modes.

If there is an open in the circuit, noise can be heard from the speakers when changing the sound source.

If there is a short in the circuit, even though the radio and display receiver assembly is functioning normally, no sound or only an extremely faint sound can be heard.

WIRING DIAGRAM

E422195E03
1.25,1.042 1.719,1.198 0.469,0.156 10 false MUTE 5.552,1.052 5.969,1.219 0.417,0.167 10 false MUT1 1.771,0.906 2.01,1.135 0.24,0.229 10 false 12 5.333,0.917 5.594,1.125 0.26,0.208 10 false 6 0.5,1.896 0.917,2.073 0.417,0.177 10 false H93 5.354,2.083 6.469,2.427 1.115,0.344 10 false Television Display Assembly 5.365,1.927 5.74,2.115 0.375,0.188 10 false W14 0.49,2.063 2.188,2.448 1.698,0.385 10 false Radio and Display Receiver Assembly

PROCEDURE

1.INSPECT TELEVISION DISPLAY ASSEMBLY
a.
E237416C35
1.531,0.448 1.99,0.708 0.458,0.26 2.542,2.688 2.365,2.688 2.365,2.688 1.927,1.844 true 0.083,0.094 0.396,0.292 0.313,0.198 10 false *a 1.604,0.479 1.99,0.656 0.385,0.177 10 false W14 2.667,2.635 3.083,2.823 0.417,0.188 10 false MUT1
*a Component with harness connected
(Television Display Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
W14-6 (MUT1) - Body ground Ignition switch ACC
RSE system playing
→ Changing source
3.5 V or higher
→ Below 1 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEVISION DISPLAY ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEVISION DISPLAY ASSEMBLY)
a.

Disconnect the W14 television display assembly connector.


b.

Disconnect the H93 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W14-6 (MUT1) - H93-12 (MUTE) Always Below 1 Ω
W14-6 (MUT1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE TELEVISION DISPLAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE TELEVISION DISPLAY ASSEMBLY
a.

Replace the television display assembly and check if it operates normally.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>TELEVISION DISPLAY>REMOVAL

OK:

The rear seat entertainment system operates normally.



Result:
Proceed to
OK
NG



OK

END (TELEVISION DISPLAY ASSEMBLY WAS DEFECTIVE)

NG

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE