Home › Audio / Visual / Telematics › AUDIO / VIDEO › REAR SEAT ENTERTAINMENT SYSTEM › from 2020.08
RM27T0E _56 Audio / Visual / Telematics _053720 AUDIO / VIDEO _0260968 REAR SEAT ENTERTAINMENT SYSTEM J

AUDIO / VIDEO  REAR SEAT ENTERTAINMENT SYSTEM  AVC-LAN Circuit  


DESCRIPTION

Each unit of the rear seat entertainment system connected to the AVC-LAN (communication bus) transmits switch signals through the AVC-LAN.

If a short to +B or short to ground occurs in the AVC-LAN, the rear seat entertainment system will not function normally because communication is not possible.

WIRING DIAGRAM

E277861E44
4.688,1.823 6.573,2.031 1.885,0.208 10 false Television Display Assembly 0.615,1.844 3.281,2.073 2.667,0.229 10 false Radio and Display Receiver Assembly 0.938,2.396 2.938,2.615 2,0.219 10 false : AVC-LAN Communication Line 5.083,0.385 5.698,0.583 0.615,0.198 10 false TX1+ 5.083,1.188 5.698,1.385 0.615,0.198 10 false TX1- 4.719,1.635 5.333,1.833 0.615,0.198 10 false W14 0.625,1.656 1.24,1.854 0.615,0.198 10 false H92 1.802,0.396 2.417,0.594 0.615,0.198 10 false TX+ 1.833,1.177 2.448,1.375 0.615,0.198 10 false TX- 2.156,0.26 2.771,0.458 0.615,0.198 10 false 19 2.146,1.052 2.76,1.25 0.615,0.198 10 false 20 4.906,0.26 5.521,0.458 0.615,0.198 10 false 4 4.906,1.042 5.521,1.24 0.615,0.198 10 false 5

CAUTION / NOTICE / HINT

HINT:

The radio and display receiver assembly is the master unit.


PROCEDURE

1.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

b.
E394515C42
1.583,0.813 1.99,1.031 0.406,0.219 1.802,2.615 2.167,2.01 true 2.552,2.615 2.5,2.01 true 1.667,0.833 2.052,1.01 0.385,0.177 10 false H92 1.667,2.646 2.073,2.896 0.406,0.25 10 false TX- 2.448,2.656 2.823,2.875 0.375,0.219 10 false TX+ 0.188,0.167 0.5,0.365 0.313,0.198 10 false *a
*a Component without harness connected
(Radio and Display Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H92-19 (TX+) - H92-20 (TX-) Always 60 to 80 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)

NG

2.CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)
a.

Disconnect the W14 television display assembly connector.


b.

Disconnect the H92 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W14-4 (TX1+) - H92-19 (TX+) Always Below 1 Ω
W14-5 (TX1-) - H92-20 (TX-) Always Below 1 Ω
W14-4 (TX1+) - Body ground Always 10 kΩ or higher
W14-5 (TX1-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT MALFUNCTIONING PARTS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MALFUNCTIONING PARTS
a.

Disconnect and reconnect each slave unit one by one until the master unit returns to normal operation.

HINT:
·

Check all slave units.

·

If disconnecting a slave unit causes the master unit to return to normal operation, the slave unit is defective and should be replaced.



OK:

Master unit returns to normal operation.



Result:
Proceed to
OK
NG



OK

REPLACE MALFUNCTIONING PARTS

NG