Home › Drivetrain › AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for 1GD-FTV) › from 2020.08
RM27T0E _52 Drivetrain _053698 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0260782 AUTOMATIC TRANSMISSION SYSTEM(for 1GD-FTV) J

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1GD-FTV)  Pattern Select Switch Sport Mode Circuit  


DESCRIPTION

The ECM memory contains the programs for the normal and sport shift patterns and lock-up pattern.

By following the programs corresponding to the signals from the SPORT mode switch (eco mode switch (drive mode)), the park/neutral position switch and other various sensors, the ECM switches the solenoid valves on and off, and controls the transmission gear change and the lock-up clutch operation.

WIRING DIAGRAM

C382764E03
3,3.083 5.292,3.281 2.292,0.198 10 false Shift Position Indicator 3,2.917 3.615,3.115 0.615,0.198 10 false G303 1.406,2.927 2.573,3.302 1.167,0.375 10 false Eco Mode Switch (Drive Mode) 5.5,0.792 6.115,0.99 0.615,0.198 10 false SPCN 3.885,0.792 4.042,0.99 0.156,0.198 10 false B 4.156,1.719 4.469,1.917 0.313,0.198 10 false 15 5.156,1.719 5.469,1.917 0.313,0.198 10 false 12 5.49,1.719 6.104,1.917 0.615,0.198 10 false PWMS 3.875,1.719 4.031,1.917 0.156,0.198 10 false P 5.208,0.792 5.365,0.99 0.156,0.198 10 false 9 4.135,0.792 4.448,0.99 0.313,0.198 10 false 13 2.417,1.729 3.146,2 0.729,0.271 10 false SPORT 2.344,0.792 3.26,0.99 0.917,0.198 10 false NORMAL 3.042,1.719 3.198,1.917 0.156,0.198 10 false 3 3.063,2.344 3.219,2.542 0.156,0.198 10 false 5 2.583,2.344 3.042,2.542 0.458,0.198 10 false GND 3.021,0.792 3.177,0.99 0.156,0.198 10 false 7 4.156,2.344 4.469,2.542 0.313,0.198 10 false 18 3.885,2.333 4.042,2.531 0.156,0.198 10 false E 5.969,2.625 6.438,2.906 0.469,0.281 10 false ECM 5.958,2.448 6.573,2.646 0.615,0.198 10 false G184 6.406,1.542 6.865,1.74 0.458,0.198 10 false 12 V 6.406,0.594 6.865,0.792 0.458,0.198 10 false 12 V

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SHIFT POSITION INDICATOR - BODY GROUND)
a.
C384711C02
1.458,0.156 1.948,0.458 0.49,0.302 2.802,1.844 2.177,1.406 true 1.542,0.24 2.156,0.438 0.615,0.198 10 false G303 0.125,0.115 0.438,0.313 0.313,0.198 10 false *a 2.875,1.823 3.031,2.021 0.156,0.198 10 false E
*a Front view of wire harness connector
(to Shift Position Indicator)


Disconnect the shift position indicator connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G303-18 (E) - Body ground Always Below 1 Ω




OK

2.CHECK SHIFT POSITION INDICATOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK SHIFT POSITION INDICATOR
a.
C384710C02
1.896,1.448 2.656,1.698 true 2.188,1.375 2.698,0.99 true 0.75,1.802 1.26,1.417 true 0.156,0.156 0.469,0.354 0.313,0.198 10 false *a 2.76,1.615 3.073,1.813 0.313,0.198 10 false P 2.792,0.885 2.948,1.083 0.156,0.198 10 false B 0.615,1.792 0.771,1.99 0.156,0.198 10 false E
*a Component without harness connected
(Shift Position Indicator)


Disconnect the shift position indicator connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
15 (P) - 18 (E) SPORT mode switch pushed and held Below 10 Ω
SPORT mode switch not pushed 10 kΩ or higher
13 (B) - 18 (E) NORMAL mode switch pushed and held Below 10 Ω
NORMAL mode switch not pushed 10 kΩ or higher




OK

3.CHECK HARNESS AND CONNECTOR (SHIFT POSITION INDICATOR - ECM)

NG

4.INSPECT ECO MODE SWITCH (DRIVE MODE)
3.CHECK HARNESS AND CONNECTOR (SHIFT POSITION INDICATOR - ECM)
a.
C318001C28
2.208,0.26 2.635,0.5 0.427,0.24 1.792,2.76 2.354,1.906 true 2.969,2.75 2.552,1.906 true 1.51,2.823 2.313,3.021 0.802,0.198 10 false 12 (PWMS) 2.26,0.323 2.833,0.5 0.573,0.177 10 false G184 0.125,0.115 0.448,0.281 0.323,0.167 10 false *a 2.76,2.823 3.427,3.052 0.667,0.229 10 false 8 (SPCN)
*a Rear view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G184-12 (PWMS) - Body ground SPORT mode switch pushed and held Below 10 Ω
SPORT mode switch not pushed 10 kΩ or higher
G184-9 (SPCN) - Body ground NORMAL mode switch pushed and held Below 10 Ω
NORMAL mode switch not pushed 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT ECO MODE SWITCH (DRIVE MODE)
a.
C380111C24
0.656,1.094 1.146,1.094 true 2.021,1.448 2.542,1.875 true 1.792,1 2.427,0.24 true 0.083,0.083 0.333,0.323 0.25,0.24 10 false *1 2.51,0.146 3.375,0.344 0.865,0.198 10 false SPORT 0.333,1.031 0.646,1.24 0.313,0.208 10 false GND 2.646,1.875 3.292,2.042 0.646,0.167 10 false NORMAL
*a Eco Mode Switch (Drive Mode)


Remove the eco mode switch (drive mode) connector (See pageDrivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>COMBINATION SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
3 (SPORT) - 5 (GND) SPORT mode switch pushed and held Below 10 Ω
SPORT mode switch not pushed 10 kΩ or higher
7 (NORMAL) - 5 (GND) NORMAL mode switch pushed and held Below 10 Ω
NORMAL mode switch not pushed 10 kΩ or higher




OK

NG