Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM › from 2020.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0442223 REAR VIEW MONITOR SYSTEM J

PARK ASSIST / MONITORING  REAR VIEW MONITOR SYSTEM  Image from Camera for Rear View Monitor is Abnormal  


DESCRIPTION

The display signal of the rear television camera assembly is transmitted to the radio and display receiver assembly.

WIRING DIAGRAM

E418133E08
0.26,2.594 1.354,2.854 1.094,0.26 10 false v2*1, X9*2 5.375,2.854 7.063,3.24 1.688,0.385 10 false Radio and Display Receiver Assembly 5.396,2.625 5.854,2.823 0.458,0.198 10 false H93 0.219,2.76 2.74,3.01 2.521,0.25 10 false Rear Television Camera Assembly 0.083,3.604 1.271,3.802 1.188,0.198 10 false *3: Shielded 3.396,2.271 3.802,2.531 0.406,0.26 10 false *3 1.125,0.698 1.458,0.917 0.333,0.219 10 false CB+ 1.104,1.125 1.448,1.333 0.344,0.208 10 false CV+ 1.135,1.688 1.448,1.896 0.313,0.208 10 false CV- 1,2.167 1.458,2.365 0.458,0.198 10 false CGND 5.698,2.26 6.156,2.458 0.458,0.198 10 false CGND 5.771,1.594 6.229,1.792 0.458,0.198 10 false V- 5.74,1.125 6.198,1.323 0.458,0.198 10 false V+ 5.729,0.656 6.188,0.854 0.458,0.198 10 false CA+ 5.406,0.49 5.615,0.688 0.208,0.198 10 false 30 5.406,0.979 5.615,1.177 0.208,0.198 10 false 28 5.417,1.438 5.625,1.635 0.208,0.198 10 false 29 5.417,2.125 5.625,2.323 0.208,0.198 10 false 27 1.531,0.5 1.74,0.698 0.208,0.198 10 false 6 1.573,0.948 1.781,1.146 0.208,0.198 10 false 3 1.552,1.406 1.76,1.604 0.208,0.198 10 false 2 1.531,2.073 1.74,2.271 0.208,0.198 10 false 5 0.083,3.354 1.563,3.604 1.479,0.25 10 false *2: w/o Tire Carrier 0.083,3.094 1.563,3.344 1.479,0.25 10 false *1: w/ Tire Carrier

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the H93 radio and display receiver assembly connector.


b.

Disconnect the v2*1 or X9*2 rear television camera assembly connector.

*1: w/ Tire Carrier

*2: w/o Tire Carrier



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Tire Carrier:
Tester Connection Condition Specified Condition
H93-30 (CA+) - v2-6 (CB+) Always Below 1 Ω
H93-28 (V+) - v2-3 (CV+) Always Below 1 Ω
H93-29 (V-) - v2-2 (CV-) Always Below 1 Ω
H93-27 (CGND) - v2-5 (CGND) Always Below 1 Ω
H93-30 (CA+) or v2-6 (CB+) - Body ground Always 10 kΩ or higher
H93-28 (V+) or v2-3 (CV+) - Body ground Always 10 kΩ or higher
H93-29 (V-) or v2-2 (CV-) - Body ground Always 10 kΩ or higher
H93-27 (CGND) or v2-5 (CGND) - Body ground Always 10 kΩ or higher

w/o Tire Carrier:
Tester Connection Condition Specified Condition
H93-30 (CA+) - X9-6 (CB+) Always Below 1 Ω
H93-28 (V+) - X9-3 (CV+) Always Below 1 Ω
H93-29 (V-) - X9-2 (CV-) Always Below 1 Ω
H93-27 (CGND) - X9-5 (CGND) Always Below 1 Ω
H93-30 (CA+) or X9-6 (CB+) - Body ground Always 10 kΩ or higher
H93-28 (V+) or X9-3 (CV+) - Body ground Always 10 kΩ or higher
H93-29 (V-) or X9-2 (CV-) - Body ground Always 10 kΩ or higher
H93-27 (CGND) or X9-5 (CGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
E402607C38
1.5,0.156 2.021,0.479 0.521,0.323 0.583,1.646 0.771,1.646 0.771,1.646 0.969,1.24 true 0.781,2.01 0.969,2.01 0.969,2.01 1.438,1.24 true 1.615,0.24 2.073,0.438 0.458,0.198 10 false H93 0.24,0.135 0.698,0.333 0.458,0.198 10 false *a 0.25,1.542 0.708,1.74 0.458,0.198 10 false CA+ 0.271,1.938 0.781,2.135 0.51,0.198 10 false CGND
*a Component with harness connected
(Radio and Display Receiver Assembly)


Remove the radio and display receiver assembly with its connectors still connected.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H93-27 (CGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H93-30 (CA+) - Body ground Ignition switch ACC 5.5 to 7.05 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

3.CHECK REAR TELEVISION CAMERA ASSEMBLY

NG

3.CHECK REAR TELEVISION CAMERA ASSEMBLY
a.

Remove the radio and display receiver assembly with its connectors still connected.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL

E402606C36
0.958,1.073 1.531,1.344 0.573,0.271 2.698,2.885 2.875,2.885 2.875,2.885 3.135,2.25 true 5,2.792 5.177,2.792 5.177,2.792 5.438,2.156 true 3.208,2.167 3.375,2.917 3.375,2.917 3.531,2.917 true 5.542,2.104 5.708,2.854 5.708,2.854 5.865,2.854 true 0.344,2.573 0.521,2.573 0.521,2.573 0.635,1.969 true 0.74,1.958 0.865,2.823 0.865,2.823 1.021,2.823 true 0.177,0.99 0.49,1.188 0.313,0.198 10 false *a 2.635,0.979 2.948,1.177 0.313,0.198 10 false *b 4.948,0.927 5.26,1.125 0.313,0.198 10 false *c 2.531,2.792 2.844,2.99 0.313,0.198 10 false *d 3.583,2.813 3.896,3.01 0.313,0.198 10 false *e 4.823,2.698 5.135,2.896 0.313,0.198 10 false *d 5.917,2.76 6.229,2.958 0.313,0.198 10 false *e 2.448,1.792 2.906,2.031 0.458,0.24 10 false GND 4.75,1.813 5.208,2.052 0.458,0.24 10 false GND 1.073,2.75 1.385,2.948 0.313,0.198 10 false V+ 0.135,2.479 0.448,2.677 0.313,0.198 10 false V- 1.073,1.125 1.719,1.438 0.646,0.313 10 false H93
*a Component with harness connected
(Radio and Display Receiver Assembly)
*b Waveform 1
*c Waveform 2 *d Synchronization Signal
*e Video Waveform - -



b.

Check the waveform of the rear television camera assembly using an oscilloscope.

HINT:
·

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.

·

The video waveform changes according to the image sent by the rear television camera assembly.



Item Content
Terminal No. (Symbol) H93-28 (V+) - H93-29 (V-)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Waveform 1: Ignition switch ON, shift lever in R, camera lens not covered, displaying an image
Waveform 2: Ignition switch ON, shift lever in R, camera lens covered, blacking out screen

OK:

Waveform is as shown in the illustration.



Result:
Proceed to
OK
NG



OK

NG

4.CHECK REAR TELEVISION CAMERA ASSEMBLY
4.CHECK REAR TELEVISION CAMERA ASSEMBLY
a.

b.

Check if the same malfunction recurs when the rear view monitor screen is displayed.

OK:

Malfunction does not reoccur (returns to normal).



Result:
Proceed to
OK
NG



OK

END (REAR TELEVISION CAMERA ASSEMBLY IS DEFECTIVE)

NG