The skid control ECU receives signals from the ECM via the CAN communication system.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1437 | When the IG1 terminal voltage is 10 V or higher and the vehicle speed is 15 km/h (9 mph) or more, data cannot be sent from the ECM for 2 seconds or more. | ·
Engine control system ·
CAN communication system ·
Skid control ECU (Master cylinder solenoid) |
When replacing the skid control ECU (master cylinder solenoid), perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>CALIBRATION).
Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to the DTC (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>CHECK FOR INTERMITTENT PROBLEMS).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| EFI Communication Open | EFI communication open detection/ Error or Normal | Normal | - |
Normal (there are no momentary interruptions).
Perform the above inspection before removing the sensor and connector.
OK
NG
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 15 km/h (9 mph) or more for 10 seconds or more.
Check that no CAN communication system DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>DTC CHECK / CLEAR).
Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC C1437 is not output | A |
| DTC C1437 is output | B |
| CAN communication system DTC is output (w/o Central Gateway ECU) | C |
| CAN communication system DTC is output (w/ Central Gateway ECU) | D |
for 1GR-FE, refer to the following sections.
for 2TR-FE, refer to the following sections.
for 1GD-FTV, refer to the following sections.
for 1GD-FTV (w/ Urea SCR System): See pageEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>HOW TO PROCEED WITH TROUBLESHOOTING
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B
C
D
Turn the ignition switch off.
Repair or replace the harness or connector.
Check for any momentary interruption between the skid control ECU and ECM (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>CHECK FOR INTERMITTENT PROBLEMS).
Check that there is no momentary interruption.
NEXT
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 15 km/h (9 mph) or more for 10 seconds or more.
Check that no CAN communication system DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>DTC CHECK / CLEAR).
Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC C1437 is not output | A |
| DTC C1437 is output (for LHD) | B |
| DTC C1437 is output (for RHD) | C |
| CAN communication system DTC is output (w/ Central Gateway ECU) | D |
| CAN communication system DTC is output (w/o Central Gateway ECU) | E |
A
B
C
D
E