The ECM operates the air pump heater relay which causes the air pump heater to operate.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P144C | Open or short in the air pump heater relay circuit for 5 seconds (1 trip detection logic). | ·
Open or short in air pump heater relay circuit ·
Air pump heater relay ·
ECM |
| P144D | Open or short in the air pump heater relay circuit for 5 seconds (1 trip detection logic). | ·
Open or short in air pump heater relay circuit ·
Air pump heater relay ·
ECM |
| Frequency of operation | Continuous |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS on.
Wait for 10 seconds.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the Air Pump Heater.
Activate the air pump heater for 10 seconds or more.
The Active Test activates the air pump heater for up to 60 seconds.
To protect the air pump heater, do not perform this test more than 4 times in a row.
Enter the following menus: Powertrain / Engine and ECT / Trouble Code.
Read Pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P144C or P144D.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
Refer to DTC P0412 (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>P0412).
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page ).
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When disconnecting and reconnecting the battery.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Inspect the air pump heater relay (AIR PMP HTR) (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).
OK
NG
Remove the air pump heater relay (AIR PMP HTR).
Disconnect the cable from the negative (-) battery terminal.
Disconnect the cable from the positive (+) battery terminal.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Air pump heater relay (AIR PMP HTR) terminal 2 - Battery positive (+) terminal | Always | Below 1 Ω |
| Air pump heater relay (AIR PMP HTR) terminal 2 or Battery positive (+) terminal - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the air pump heater relay (AIR PMP HTR).
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Air pump heater relay (AIR PMP HTR) terminal 1 - G181-4 (HAI1) | Always | Below 1 Ω |
| Air pump heater relay (AIR PMP HTR) terminal 1 or G181-4 (HAI1) - Body ground | Always | 10 kΩ or higher |
OK
NG