Home › Drivetrain › R150F (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSMISSION UNIT › from 2018.06
RM27T0E _52 Drivetrain _053702 R150F MANUAL TRANSMISSION / TRANSAXLE _0260834 MANUAL TRANSMISSION UNIT A

R150F MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION UNIT  DISASSEMBLY  


PROCEDURE

Hide 33101A 1.REMOVE MANUAL TRANSMISSION FILLER PLUG

a.
D029023

Remove the manual transmission filler plug and gasket from the manual transmission case.


Hide 33104 2.REMOVE DRAIN PLUG

a.
D029024

Remove the drain plug and gasket from the manual transmission case.


Hide 31204 3.REMOVE CLUTCH RELEASE FORK SUB-ASSEMBLY

Hide 31230 4.REMOVE CLUTCH RELEASE BEARING ASSEMBLY

Hide 31236B 5.REMOVE RELEASE FORK SUPPORT

a.
D025933

Remove the release fork support from the clutch housing.


Hide 31126 6.REMOVE CLUTCH RELEASE FORK BOOT

a.
C216207

Remove the clutch release fork boot from the clutch housing.


Hide 31111 7.REMOVE CLUTCH HOUSING

a.
C216208

Remove the 9 bolts.


b.
D029029

Using a plastic-faced hammer, tap off the clutch housing from the manual transmission case.


Hide 84210 8.REMOVE BACK-UP LIGHT SWITCH ASSEMBLY

a.
D029030E12
1.927,1.188 2.052,1.875 false 2.354,1.875 2.052,1.875 false 2.417,1.802 2.708,1.948 0.292,0.146 10 false SST

Using SST, remove the back-up light switch assembly and gasket from the manual transmission case.

SST
09817-16011  


Hide 9.REMOVE RESTRICT PIN

a.
C216210

Remove the 2 restrict pins from the transfer adapter.


Hide 33506F 10.REMOVE FLOOR SHIFT CONTROL SHIFT LEVER RETAINER SUB-ASSEMBLY

a.
C216211

Remove the 4 bolts and floor shift control shift lever retainer sub-assembly.


b.

Remove the gasket.


Hide 36117 11.REMOVE TRANSFER ADAPTER

a.
C216214

Remove the 10 bolts.


b.
C216215

Using a brass bar and hammer, tap off the transfer adapter from the manual transmission case.


Hide 33124E 12.REMOVE TRANSFER OIL RECEIVER PIPE

a.
D029037

Remove the transfer oil receiver pipe from the transfer adapter.


Hide 33251 13.REMOVE SHIFT AND SELECT LEVER

a.
C216209

Remove the bolt from the shift lever housing.


b.
C216212E01
1.368,0.128 1.518,0.275 0.150,0.147 10 *1 0.177,0.851 0.327,0.999 0.150,0.147 10 *2 2.156,0.225 1.592,0.225 false 0.39,0.934 0.735,0.934 false 0.735,0.934 0.735,1.381 false

Remove the shift and select lever and shift lever housing from the transfer adapter.

Text in Illustration
*1 Shift Lever Housing
*2 Shift and Select Lever


Hide 33280 14.REMOVE REVERSE RESTRICT PIN ASSEMBLY

a.
D029040

Using a T40 "TORX" socket wrench, remove the reverse restrict pin plug.


b.
D033421

Using a 5 mm pin punch and hammer, tap out the reverse restrict pin slotted spring pin.


c.
D029042

Remove the reverse restrict pin assembly.


Hide 36117A 15.REMOVE TRANSFER ADAPTER OIL SEAL

a.
D029043

Using a screwdriver and hammer, tap out the transfer adapter oil seal from the transfer adapter.


Hide 33131 16.REMOVE FRONT BEARING RETAINER

a.
D025950

Remove the 8 bolts.


b.
D025951

Using a brass bar and hammer, tap off the front bearing retainer from the manual transmission case.


Hide 33131A 17.REMOVE TRANSMISSION FRONT BEARING RETAINER OIL SEAL

a.
C215999E01
2.509,0.381 2.830,0.542 0.321,0.161 10 SST 2.433,0.457 2.043,0.457 false 2.043,0.457 2.043,0.928 false

Secure the front bearing retainer in a vise between aluminum plates.


b.

Using SST, tap out the transmission front bearing retainer oil seal.

SST
09308-00010  


Hide 33311B 18.REMOVE FRONT BEARING SHAFT SNAP RING

a.
D025953

Using a snap ring expander, remove the front bearing shaft snap ring from the input shaft front bearing.


Hide 33411D 19.REMOVE FRONT NO. 1 COUNTER GEAR BEARING SNAP RING

a.
D025954

Using a snap ring expander, remove the front No. 1 counter bearing snap ring from the front counter gear bearing.


Hide 33111 20.REMOVE MANUAL TRANSMISSION CASE

a.
D029044

Using a brass bar and hammer, tap off the manual transmission case from the intermediate plate.


Hide 33449B 21.REMOVE TRANSMISSION MAGNET

a.
D025957

Remove the transmission magnet from the intermediate plate.


Hide 22.FIX INTERMEDIATE PLATE

a.
C288239

Secure the intermediate plate in a vise between aluminum plates.


Hide 33275 23.REMOVE NO. 1 SHIFT DETENT BALL SPRING SEAT

a.
C295052

for Type A:

Using a 6 mm hexagon socket wrench, remove the No. 1 shift detent ball spring seat from the intermediate plate.


b.
D029046

for Type B:

Using a T40 "TORX" socket wrench, remove the No. 1 shift detent ball spring seat from the intermediate plate.


c.
D025960

Using a magnet hand, remove the compression spring and detent ball from the intermediate plate.


d.
C295053

for Type A:

Using a 6 mm hexagon socket wrench, remove the 2 No. 1 shift detent ball spring seats from the intermediate plate.


e.
C288240

for Type B:

Using a T40 "TORX" socket wrench, remove the 2 No. 1 shift detent ball spring seats from the intermediate plate.


f.
C288241

Using a magnet hand, remove the 2 compression springs and 2 detent balls from the intermediate plate.


Hide 33243A 24.REMOVE NO. 2 GEAR SHIFT FORK SHAFT

a.
C288242

Using 2 screwdrivers and a hammer, tap off the snap ring from the No. 2 gear shift fork shaft.

NOTICE:

Use a piece of cloth to prevent the snap ring from flying off.



b.
C288243

Remove the bolt from the No. 2 shift fork.


c.
C288244

Remove the No. 2 gear shift fork shaft from the intermediate plate.


d.
C288245

Remove the No. 2 shift fork from the No. 2 transmission hub sleeve.


e.
D025967

Using a magnet hand, remove the No. 1 shift interlock roller and shift interlock pin from the intermediate plate.


Hide 33242 25.REMOVE NO. 1 GEAR SHIFT FORK SHAFT

a.
C288246

Using 2 screwdrivers and a hammer, tap off the snap ring from the No. 1 gear shift fork shaft.

NOTICE:

Use a piece of cloth to prevent the snap ring from flying off.



b.
C288247

Remove the bolt from the No. 1 shift fork.


c.
C288248

Remove the No. 1 gear shift fork shaft from the intermediate plate.


d.
C288249

Remove the No. 1 shift fork from the reverse gear.


Hide 33244D 26.REMOVE NO. 3 GEAR SHIFT FORK SHAFT

a.
C272919

Using a 5 mm pin punch and hammer, tap out the shift fork set slotted spring pin from the No. 3 shift fork.


b.
C288250

Using 2 screwdrivers and a hammer, tap off the snap ring from the No. 3 gear shift fork shaft.

NOTICE:

Use a piece of cloth to prevent the snap ring from flying off.



c.
C289009

Using a magnet hand, remove the straight pin from the reverse shift fork.


d.
D029058

Remove the No. 3 shift fork and No. 3 gear shift fork shaft from the intermediate plate.


e.
D025975

Using a magnet hand, remove the No. 1 shift interlock roller from the intermediate plate.


Hide 33211 27.REMOVE REVERSE SHIFT FORK

a.
C290803

Remove the reverse shift fork from the reverse shift arm.


Hide 33228 28.REMOVE REVERSE SHIFT ARM BRACKET

a.
C291033

Remove the torsion spring from the reverse shift arm bracket.


b.
C291034

Remove the 2 bolts and reverse shift arm bracket from the intermediate plate.


c.
C291035

Using a screwdriver, pry out the snap ring from the reverse shift arm bracket.


d.
C291036

Remove the reverse shift arm from the reverse shift arm bracket.


Hide 33321B 29.REMOVE OUTPUT SHAFT BEARING SHAFT SNAP RING (for Rear Bearing Side)

a.
D029059

Using 2 screwdrivers and a hammer, tap off the output shaft bearing shaft snap ring from the output shaft rear bearing.

NOTICE:

Use a piece of cloth to prevent the snap ring from flying off.



Hide 33321A 30.REMOVE OUTPUT SHAFT REAR BEARING

a.
U149029E01
0.077,0.737 0.386,0.892 0.309,0.156 10 SST 0.768,0.82 0.481,0.82 false 0.589,0.82 0.589,1.301 0.589,1.301 1.407,1.301 false 0.843,0.987 0.589,0.987 false 1.093,2.32 1.402,2.476 0.309,0.156 10 SST 2.246,2.389 1.56,2.389 false 2.067,2.389 2.067,2.019 2.067,2.019 2.564,2.019 false 2.484,2.085 2.067,2.085 false 2.998,1.21 3.205,1.420 0.207,0.209 10 *a 0.156,1.583 0.363,1.792 0.207,0.209 10 *b

Using SST, remove the output shaft rear bearing and output shaft spacer from the output shaft.

SST
09950-40011  (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04051, 09957-04010, 09958-04011)
09950-60010  (09951-00300)

Text in Illustration
*a Hold
*b Turn


Hide 31.INSPECT COUNTER 5TH GEAR THRUST CLEARANCE

a.
D025991

Using a feeler gauge, measure the thrust clearance.

Standard clearance:

0.10 to 0.35 mm (0.00394 to 0.0137 in.)


If the clearance is not as specified, replace the counter 5th gear.



Hide 32.INSPECT COUNTER 5TH GEAR RADIAL CLEARANCE

a.
D025992

Using a dial indicator, measure the radial clearance.

Standard clearance:

0.015 to 0.068 mm (0.000591 to 0.00267 in.)


If the clearance is not as specified, replace the counter 5th gear bearing with a new one.



Hide 33421R 33.REMOVE COUNTER GEAR REAR SHAFT SNAP RING

a.
C272923

Using 2 screwdrivers and a hammer, tap off the counter gear rear shaft snap ring from the counter gear.

NOTICE:

Use a piece of cloth to prevent the counter gear rear shaft snap ring from flying off.



Hide 33395 34.REMOVE NO. 3 TRANSMISSION HUB SLEEVE

a.
C282116

Remove the No. 3 transmission hub sleeve from the counter 5th gear.


Hide 33318 35.REMOVE NO. 5 GEAR SPLINE PIECE

a.
C295487E01
0.123,1.336 0.332,1.536 0.209,0.200 10 *b 2.352,1.674 2.561,1.874 0.209,0.200 10 *a 0.055,0.156 0.363,0.344 0.309,0.188 10 SST 0.416,0.236 0.496,0.236 0.496,0.236 0.604,1.026 false 2.318,1.15 2.626,1.338 0.309,0.188 10 SST 2.679,1.23 2.759,1.23 2.759,1.23 2.823,0.787 false

Using SST, remove the counter 5th gear together with the counter 5th gear bearing, 2 No. 3 synchromesh shifting keys, No. 3 synchromesh shifting key spring, No. 3 synchronizer ring and No. 5 gear spline piece from the counter 5th gear.

SST
09950-50013  (09951-05010, 09952-05010, 09953-05020, 09954-05021, 09957-04010)

Text in Illustration
*a Hold
*b Turn


Hide 33318 36.REMOVE NO. 5 GEAR SPLINE PIECE

a.
C250776

Remove the No. 5 gear spline piece from the counter 5th gear.


Hide 33384A 37.REMOVE OUTER NO. 3 SYNCHRONIZER RING

a.

Remove the outer No. 3 synchronizer ring from the counter 5th gear.


Hide 33428B 38.REMOVE COUNTER 5TH GEAR BEARING

a.
C089839

Remove the counter 5th gear bearing from the counter 5th gear.


Hide 33394B 39.REMOVE NO. 3 SYNCHROMESH SHIFTING KEY

a.
C247403

Using a snap ring expander, remove the shaft snap ring.


b.
C250077E01
2.75,0.417 2.75,0.167 2.75,0.167 2.417,0.167 false 1.917,0.594 1.917,0.333 1.917,0.333 1.583,0.333 false 0.75,0.75 0.75,0.49 0.75,0.49 0.417,0.49 false 2.198,0.083 2.365,0.25 0.167,0.167 10 false *1 1.365,0.25 1.531,0.417 0.167,0.167 10 false *2 0.198,0.417 0.365,0.583 0.167,0.167 10 false *3

Remove the No. 3 synchromesh shifting keys and No. 3 synchromesh shifting key spring from the counter 5th gear.

Text in Illustration
*1 No. 3 Synchromesh Shifting Key Spring
*2 No. 3 Synchromesh Shifting Key
*3 Counter 5th Gear


Hide 33349 40.REMOVE 5TH GEAR THRUST WASHER

a.
C272927

Remove the 5th gear thrust washer from the counter gear.


Hide 33349C 41.REMOVE 5TH GEAR THRUST WASHER PIN

a.
C272929

Remove the 5th gear thrust washer pin from the counter gear.


Hide 33151 42.REMOVE OUTPUT SHAFT REAR BEARING RETAINER

a.
D026001

Remove the 4 bolts and output shaft rear bearing retainer from the intermediate plate.


Hide 33402 43.REMOVE REVERSE IDLER GEAR SUB-ASSEMBLY

a.
D026002

Pull out the reverse idler gear shaft from the rear side and remove the reverse idler gear sub-assembly from the intermediate plate.


Hide 33411P 44.REMOVE COUNTER SHAFT CENTER BEARING

a.
C272931

Using a snap ring expander, remove the snap ring from the counter shaft center bearing.


b.
C295488E01
2.645,0.49 2.968,0.646 0.323,0.156 10 SST 1.828,0.776 1.828,0.576 1.828,0.576 2.599,0.576 false 1.931,0.918 1.931,0.576 false 2.07,1.154 2.07,0.576 false 2.345,1.799 2.668,1.955 0.323,0.156 10 SST 1.747,2.311 1.908,1.885 1.908,1.885 2.299,1.885 false 1.796,2.352 1.957,1.885 false

Using SST, remove the counter shaft center bearing from the intermediate plate.

SST
09950-40011  (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04011, 09957-04010, 09958-04011)
09950-60010  (09951-00260)

NOTICE:

Do not drop the counter gear. Hold the front side of the counter gear when removing the bearing outer race.



Hide 33421 45.REMOVE COUNTER GEAR

a.
D026005

Remove the counter gear from the intermediate plate.


Hide 33311 46.REMOVE INPUT SHAFT

a.
D026006

Remove the input shaft and No. 2 synchronizer ring from the output shaft.

NOTICE:

Do not drop the input shaft bearing or No. 2 synchronizer ring.



Hide 33321B 47.REMOVE OUTPUT SHAFT BEARING SHAFT SNAP RING (for Center Bearing Side)

a.
C272935

Using a snap ring expander, remove the output shaft bearing shaft snap ring from the output shaft center bearing.


Hide 33321 48.REMOVE OUTPUT SHAFT

a.
C272539

Using a plastic-faced hammer, remove the output shaft by tapping the intermediate plate.