Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM (w/ Reverse Shift-linked Mirror) › from 2020.08
RM27T0E _59 Vehicle Exterior _053745 MIRROR (EXT) _0327116 POWER MIRROR CONTROL SYSTEM(w/ Reverse Shift-linked Mirror) J

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM(w/ Reverse Shift-linked Mirror)  Reverse Shift-linked Function of Power Mirrors does not Operate  


DESCRIPTION

ECM sends the reverse signal to the main body ECU (multiplex network body ECU) via CAN communication. When receiving the reverse signal, the main body ECU (multiplex network body ECU) sends the reverse request signal to each outer mirror control ECU assembly. Each outer mirror control ECU assembly then performs control in response to the reverse signal.

WIRING DIAGRAM

E379438E01
1.74,1.583 4.792,1.802 3.052,0.219 10 false Main Body ECU (Multiplex Network Body ECU) 4.188,0.708 4.646,0.906 0.458,0.198 10 false ECM 2.125,2.49 3.427,2.677 1.302,0.188 10 false Vertical Mirror Motor 2.167,5.844 3.469,6.031 1.302,0.188 10 false Vertical Mirror Motor 2.281,4.74 4.573,4.927 2.292,0.188 10 false Outer Rear View Mirror Assembly LH 5.042,4.615 5.5,4.813 0.458,0.198 10 false z18 5.031,4.802 6.583,5.146 1.552,0.344 10 false Outer Mirror Control ECU Assembly LH 5.417,2.292 5.729,2.49 0.313,0.198 10 false MV 5.188,2.229 5.344,2.427 0.156,0.198 10 false 1 5.125,2.573 5.333,2.76 0.208,0.188 10 false 10 0.635,8.469 2.313,8.656 1.677,0.188 10 false : CAN Communication Line 2.24,8.031 4.531,8.219 2.292,0.188 10 false Outer Rear View Mirror Assembly RH 5.063,8.115 6.635,8.469 1.573,0.354 10 false Outer Mirror Control ECU Assembly RH 5.063,7.938 5.521,8.135 0.458,0.198 10 false z19 5.417,5.635 5.729,5.833 0.313,0.198 10 false MV 5.417,6.01 5.729,6.208 0.313,0.198 10 false M+ 5.167,5.531 5.323,5.729 0.156,0.198 10 false 1 5.104,5.896 5.313,6.083 0.208,0.188 10 false 10 2.01,2.906 3.49,3.115 1.479,0.208 10 false Horizontal Mirror Motor 2,3.854 3.438,4.146 1.438,0.292 10 false Mirror Position Sensor 2.052,6.229 3.531,6.438 1.479,0.208 10 false Horizontal Mirror Motor 2.01,7.25 3.448,7.542 1.438,0.292 10 false Mirror Position Sensor 5.406,6.417 5.719,6.615 0.313,0.198 10 false MH 5.396,6.729 5.854,6.927 0.458,0.198 10 false VDD 5.396,7.01 6.01,7.208 0.615,0.198 10 false HSSR 5.385,7.26 6,7.458 0.615,0.198 10 false VSSR 5.406,7.583 5.865,7.781 0.458,0.198 10 false GND 5.417,2.688 5.729,2.885 0.313,0.198 10 false M+ 5.417,3.083 5.729,3.281 0.313,0.198 10 false MH 5.417,3.396 5.875,3.594 0.458,0.198 10 false VDD 5.417,3.677 6.031,3.875 0.615,0.198 10 false HSSR 5.396,3.927 6.01,4.125 0.615,0.198 10 false VSSR 5.406,4.219 5.865,4.417 0.458,0.198 10 false GND 5.177,2.979 5.333,3.177 0.156,0.198 10 false 9 5.167,3.292 5.323,3.49 0.156,0.198 10 false 5 5.115,3.583 5.427,3.781 0.313,0.198 10 false 13 5.167,3.833 5.323,4.031 0.156,0.198 10 false 6 5.104,4.125 5.417,4.323 0.313,0.198 10 false 14 5.167,6.313 5.323,6.51 0.156,0.198 10 false 9 5.156,6.615 5.313,6.813 0.156,0.198 10 false 5 5.104,6.917 5.417,7.115 0.313,0.198 10 false 13 5.156,7.177 5.313,7.375 0.156,0.198 10 false 6 5.115,7.448 5.427,7.646 0.313,0.198 10 false 14

CAUTION / NOTICE / HINT

NOTICE:
·

First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this problem.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Reverse Shift-linked Mirror)>HOW TO PROCEED WITH TROUBLESHOOTING

·

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

*: w/ Door Control Battery



HINT:

The reverse shift-linked function will not activate when the mirror select switch is in the neutral position (off).


PROCEDURE

1.CHECK MEMORY AND REACTIVATION FUNCTION
a.

Turn the ignition switch to ON.


b.

Using the multiplex network master switch assembly, turn the mirror surface to the fully left position.


c.

Press the M1 switch while the SET switch is being pressed.


d.

Check that the buzzer sounds for 0.5 seconds and the mirror surface position is memorized.


e.

Using the multiplex network master switch assembly, turn the mirror surface to the fully right position.


f.

Press the M1 switch.


g.

Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the memorized fully left position.


Result:
Result Proceed to
Memory and reactivation functions are normal A
Memory function is not normal B
Reactivation function is not normal C



A

2.CHECK FOR DTC (SFI SYSTEM, ECD SYSTEM)

B

GO TO OTHER DIAGNOSTIC PROCEDURE (Power Mirror Surface Position is not Memorized)

C

GO TO OTHER DIAGNOSTIC PROCEDURE (Power Mirrors do not Return to Memorized Position)

2.CHECK FOR DTC (SFI SYSTEM, ECD SYSTEM)

Result:
Result Proceed to
OK A
NG (for 1GR-FE) B
NG (for 1GD-FTV) C
NG (for 1GD-FTV [w/ DPF]) D
NG (for 1GD-FTV [w/ Urea SCR System]) E



A

3.CHECK SHIFT POSITION INDICATOR FUNCTION

B

C

D

E

3.CHECK SHIFT POSITION INDICATOR FUNCTION
a.

Check that the shift position indicator operates.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>SYSTEM DESCRIPTION

OK:

Shift position indicator operates normally.



Result:
Proceed to
OK
NG



OK

4.CONFIRM MALFUNCTIONING PARTS

NG

4.CONFIRM MALFUNCTIONING PARTS
a.

Result:
Result Proceed to
Both the left and right outer rear view mirror assemblies do not operate A
Outer rear view mirror assembly LH does not operate B
Outer rear view mirror assembly RH does not operate C



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

5.CHECK OUTER REAR VIEW MIRROR ASSEMBLY LH

C

6.CHECK OUTER REAR VIEW MIRROR ASSEMBLY RH
5.CHECK OUTER REAR VIEW MIRROR ASSEMBLY LH
a.

Temporarily replace the outer rear view mirror assembly LH with a new or normally functioning one.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL


b.

Check that the reverse shift-linked function operates.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Reverse Shift-linked Mirror)>OPERATION CHECK

OK:

Reverse shift-linked function operates normally.



Result:
Proceed to
OK
NG



OK

END (OUTER REAR VIEW MIRROR ASSEMBLY LH IS DEFECTIVE)

NG

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY LH

6.CHECK OUTER REAR VIEW MIRROR ASSEMBLY RH
a.

Temporarily replace the outer rear view mirror assembly RH with a new or normally functioning one.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL


b.

Check that the reverse shift-linked function operates.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Reverse Shift-linked Mirror)>OPERATION CHECK

OK:

Reverse shift-linked function operates normally.



Result:
Proceed to
OK
NG



OK

END (OUTER REAR VIEW MIRROR ASSEMBLY RH IS DEFECTIVE)

NG

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH