Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM (w/ Reverse Shift-linked Mirror) › from 2017.08
RM27T0E _59 Vehicle Exterior _053745 MIRROR (EXT) _0327116 POWER MIRROR CONTROL SYSTEM(w/ Reverse Shift-linked Mirror) J

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM(w/ Reverse Shift-linked Mirror)  Power Mirror Surface Position is not Memorized  


DESCRIPTION

When the seat memory switch is operated, the switch input signal is sent via direct line from the outer mirror control ECU assembly LH*1 and RH*2 to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) then sends the memorization request or recall request signals to the outer mirror control ECU assembly LH and outer mirror control ECU assembly RH via CAN communication. The outer mirror control ECU assembly LH and outer mirror control ECU assembly RH memorize the mirror position when a memorization request signal is received, and move the mirror to the memorized position when a recall request signal is received.

*1: for LHD

*2: for RHD


WIRING DIAGRAM

E378110E01
3.417,0.99 4.031,1.188 0.615,0.198 10 false MMRY 3.74,0.313 3.896,0.51 0.156,0.198 10 false 1 3.74,0.646 3.896,0.844 0.156,0.198 10 false 2 2.219,1.01 2.833,1.208 0.615,0.198 10 false E 5.458,0.385 5.771,0.583 0.313,0.198 10 false M1 5.448,0.75 5.76,0.948 0.313,0.198 10 false M2 5.448,1.104 5.76,1.302 0.313,0.198 10 false MM 2.344,1.563 3.146,1.74 0.802,0.177 10 false K9*1, J10*2 3.99,0.313 4.146,0.51 0.156,0.198 10 false 3 3.99,0.656 4.146,0.854 0.156,0.198 10 false 4 4,1 4.156,1.198 0.156,0.198 10 false 2 5.094,1.521 5.708,1.719 0.615,0.198 10 false G217 5.083,1.74 6.719,2.146 1.635,0.406 10 false Main Body ECU (Multiplex Network Body ECU) 5.156,0.292 5.365,0.479 0.208,0.188 10 false 13 5.156,0.646 5.365,0.833 0.208,0.188 10 false 14 5.146,1.01 5.354,1.219 0.208,0.208 10 false 16 1.823,4.292 4.167,4.521 2.344,0.229 10 false Outer Rear View Mirror Assembly LH 1.792,7.01 4.135,7.24 2.344,0.229 10 false Outer Rear View Mirror Assembly RH 5.146,4.219 5.604,4.417 0.458,0.198 10 false z18 5.167,6.917 5.625,7.115 0.458,0.198 10 false z19 5.146,7.104 6.708,7.458 1.563,0.354 10 false Outer Mirror Control ECU Assembly RH 5.135,4.396 6.698,4.75 1.563,0.354 10 false Outer Mirror Control ECU Assembly LH 0.677,7.417 2.417,7.635 1.74,0.219 10 false : CAN Communication Line 5.479,2.938 5.938,3.135 0.458,0.198 10 false VDD 5.469,5.646 5.927,5.844 0.458,0.198 10 false VDD 5.469,3.229 6.083,3.427 0.615,0.198 10 false HSSR 5.469,5.948 6.083,6.146 0.615,0.198 10 false HSSR 5.479,3.5 6.094,3.698 0.615,0.198 10 false VSSR 5.479,6.229 6.094,6.427 0.615,0.198 10 false VSSR 5.479,3.802 5.938,4 0.458,0.198 10 false GND 5.479,6.521 5.938,6.719 0.458,0.198 10 false GND 1.75,3.396 3.156,3.583 1.406,0.188 10 false Mirror Position Sensor 1.75,5.833 3.156,6.021 1.406,0.188 10 false Mirror Position Sensor 1.99,1 2.146,1.198 0.156,0.198 10 false 1 2.354,1.75 3.719,1.969 1.365,0.219 10 false Seat Memory Switch 0.281,6.677 1.083,6.854 0.802,0.177 10 false *1: for LHD 0.281,7.021 1.083,7.198 0.802,0.177 10 false *2: for RHD 5.219,2.833 5.375,3.031 0.156,0.198 10 false 5 5.156,3.115 5.396,3.323 0.24,0.208 10 false 13 5.198,3.375 5.438,3.583 0.24,0.208 10 false 6 5.146,3.677 5.385,3.885 0.24,0.208 10 false 14 5.229,5.531 5.385,5.729 0.156,0.198 10 false 5 5.156,5.833 5.396,6.042 0.24,0.208 10 false 13 5.219,6.094 5.458,6.302 0.24,0.208 10 false 6 5.156,6.396 5.396,6.604 0.24,0.208 10 false 14

CAUTION / NOTICE / HINT

NOTICE:
·

First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this problem.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.

·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

*: w/ Door Control Battery



PROCEDURE

1.READ VALUE USING GTS
a.

Using the GTS, read the Data List.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Reverse Shift-linked Mirror)>DATA LIST / ACTIVE TEST

i.

for LH side:

Body Electrical > Mirror L > Data List
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Mirror Memory No.1 Mirror position memorized in memory switch M1 / OFF or ON OFF: Not memorized
ON: Memorized
-
Mirror Memory No.2 Mirror position memorized in memory switch M2 / OFF or ON OFF: Not memorized
ON: Memorized
-
Mirror Memory No.3 Mirror position memorized in memory switch M3 / OFF or ON OFF: Not memorized
ON: Memorized
Only item displayed (not supported)


ii.

for RH side:

Body Electrical > Mirror R > Data List
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Mirror Memory No.1 Mirror position memorized in memory switch M1 / OFF or ON OFF: Not memorized
ON: Memorized
-
Mirror Memory No.2 Mirror position memorized in memory switch M2 / OFF or ON OFF: Not memorized
ON: Memorized
-
Mirror Memory No.3 Mirror position memorized in memory switch M3 / OFF or ON OFF: Not memorized
ON: Memorized
Only item displayed (not supported)

OK:

The display is as specified in the normal condition column.




Result:
Proceed to
OK
NG



OK

2.CHECK SEAT MEMORY SWITCH FUNCTION

NG

8.INSPECT SEAT MEMORY SWITCH
2.CHECK SEAT MEMORY SWITCH FUNCTION
a.

When any seat memory switch (M1 or M2) is pressed, check that the driver seat moves to the memorized position.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

OK:

The driver seat moves to the memorized position.



Result:
Proceed to
OK
NG



OK

3.CHECK MEMORY AND REACTIVATION FUNCTION

NG

GO TO FRONT POWER SEAT CONTROL SYSTEM (Power Seat does not Return to Memorized Position)

3.CHECK MEMORY AND REACTIVATION FUNCTION
a.
B227715C02
0.115,0.076 0.305,0.253 0.191,0.178 10 *a
*a Turn to Fully Left Position


Turn the ignition switch to ON.


b.

Using the multiplex network master switch assembly, turn the mirror surface to the fully left position.


c.

Press the M1 switch while the SET switch is being pressed.


d.

Check that the buzzer sounds for 0.5 seconds and the mirror surface position is memorized.


e.

Using the multiplex network master switch assembly, turn the mirror surface to the fully right position.


f.

Press the M1 switch.


g.

Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the memorized fully left position.


Result:
Result Proceed to
Memory and reactivation functions on both mirrors are not normal A
Memory and reactivation functions on front door LH mirror are not normal B
Memory and reactivation functions on front door RH mirror are not normal C



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

4.REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

C

6.REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH
4.REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH
a.

Temporarily replace the outer rear view mirror assembly LH with a new or normally functioning one.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL


b.

Check that the memory and reactivation function operates.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Reverse Shift-linked Mirror)>OPERATION CHECK

OK:

Memory and reactivation function operates normally.



Result:
Proceed to
NEXT



NEXT

5.CHECK MEMORY AND REACTIVATION FUNCTION
5.CHECK MEMORY AND REACTIVATION FUNCTION
a.
B227715C02
0.115,0.076 0.305,0.253 0.191,0.178 10 *a
*a Turn to Fully Left Position


Turn the ignition switch to ON.


b.

Using the multiplex network master switch assembly, turn the mirror surface to the fully left position.


c.

Press the M1 switch while the SET switch is being pressed.


d.

Check that the buzzer sounds for 0.5 seconds and the mirror surface position is memorized.


e.

Using the multiplex network master switch assembly, turn the mirror surface to the fully right position.


f.

Press the M1 switch.


g.

Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the memorized fully left position.


Result:
Proceed to
OK
NG



OK

END (OUTER REAR VIEW MIRROR ASSEMBLY LH IS DEFECTIVE)

NG

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY LH

6.REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH
a.

Temporarily replace the outer rear view mirror assembly RH with a new or normally functioning one.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL


b.

Check that the memory and reactivation function operates.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Reverse Shift-linked Mirror)>OPERATION CHECK

OK:

Memory and reactivation function operates normally.



Result:
Proceed to
NEXT



NEXT

7.CHECK MEMORY AND REACTIVATION FUNCTION
7.CHECK MEMORY AND REACTIVATION FUNCTION
a.
B227715C02
0.115,0.076 0.305,0.253 0.191,0.178 10 *a
*a Turn to Fully Left Position


Turn the ignition switch to ON.


b.

Using the multiplex network master switch assembly, turn the mirror surface to the fully left position.


c.

Press the M1 switch while the SET switch is being pressed.


d.

Check that the buzzer sounds for 0.5 seconds and the mirror surface position is memorized.


e.

Using the multiplex network master switch assembly, turn the mirror surface to the fully right position.


f.

Press the M1 switch.


g.

Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the memorized fully left position.


Result:
Proceed to
OK
NG



OK

END (OUTER REAR VIEW MIRROR ASSEMBLY RH IS DEFECTIVE)

NG

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH

8.INSPECT SEAT MEMORY SWITCH
a.

Remove the seat memory switch.

Click hereVehicle Interior>SEAT>SEAT MEMORY SWITCH>REMOVAL


b.

Inspect the seat memory switch.

Click hereVehicle Interior>SEAT>SEAT MEMORY SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (SEAT MEMORY SWITCH - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])

NG

REPLACE SEAT MEMORY SWITCH

9.CHECK HARNESS AND CONNECTOR (SEAT MEMORY SWITCH - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])
a.

Disconnect the G217 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the K9*1 or J10*2 seat memory switch connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
G217-16 (MM) - K9-2 (MMRY) Always Below 1 Ω
G217-16 (MM) or K9-2 (MMRY) - Body ground Always 10 kΩ or higher
G217-13 (M1) - K9-3 (1) Always Below 1 Ω
G217-13 (M1) or K9-3 (1) - Body ground Always 10 kΩ or higher
G217-14 (M2) - K9-2 (2) Always Below 1 Ω
G217-14 (M2) - K9-2 (2) - Body ground Always 10 kΩ or higher
K9-1 (E) - Body ground Always Below 1 Ω


for RHD
Tester Connection Condition Specified Condition
G217-16 (MM) - J10-2 (MMRY) Always Below 1 Ω
G217-16 (MM) or J10-2 (MMRY) - Body ground Always 10 kΩ or higher
G217-13 (M1) - J10-3 (1) Always Below 1 Ω
G217-13 (M1) or J10-3 (1) - Body ground Always 10 kΩ or higher
G217-14 (M2) - J10-2 (2) Always Below 1 Ω
G217-14 (M2) - J10-2 (2) - Body ground Always 10 kΩ or higher
J10-1 (E) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR