Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM › from 2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260475 ECD SYSTEM C

1GD-FTV ENGINE CONTROL  ECD SYSTEM  P168A00  Injector #1 Internal EEPROM Malfunction  P168A44  Injector #1 Internal EEPROM Data Memory Failure  P168A46  Injector #1 Internal EEPROM Calibration / Parameter Memory Failure  P168B00  Injector #2 Internal EEPROM Malfunction  P168B44  Injector #2 Internal EEPROM Data Memory Failure  P168B46  Injector #2 Internal EEPROM Calibration / Parameter Memory Failure  P168C00  Injector #3 Internal EEPROM Malfunction  P168C44  Injector #3 Internal EEPROM Data Memory Failure  P168C46  Injector #3 Internal EEPROM Calibration / Parameter Memory Failure  P168D00  Injector #4 Internal EEPROM Malfunction  P168D44  Injector #4 Internal EEPROM Data Memory Failure  P168D46  Injector #4 Internal EEPROM Calibration / Parameter Memory Failure  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P168A00 Injector #1 Internal EEPROM Malfunction A malfunction is continuously detected in the EEPROM (fuel temperature calibration value) built into the No. 1 injector assembly for 3 seconds or more.
(1 trip detection logic)
No. 1 injector assembly Does not come on DTC stored SAE Code: P168A
P168A44 Injector #1 Internal EEPROM Data Memory Failure A malfunction is continuously detected in the EEPROM (fuel pressure calibration value) built into the No. 1 injector assembly for 3 seconds or more.
(1 trip detection logic)
No. 1 injector assembly Does not come on DTC stored SAE Code: P168A
P168A46 Injector #1 Internal EEPROM Calibration / Parameter Memory Failure A malfunction is continuously detected in the EEPROM (i-ART learning value) built into the No. 1 injector assembly for 3 seconds or more.
(1 trip detection logic)
No. 1 injector assembly Does not come on DTC stored SAE Code: P168A
P168B00 Injector #2 Internal EEPROM Malfunction A malfunction is continuously detected in the EEPROM (fuel temperature calibration value) built into the No. 2 injector assembly for 3 seconds or more.
(1 trip detection logic)
No. 2 injector assembly Does not come on DTC stored SAE Code: P168B
P168B44 Injector #2 Internal EEPROM Data Memory Failure A malfunction is continuously detected in the EEPROM (fuel pressure calibration value) built into the No. 2 injector assembly for 3 seconds or more.
(1 trip detection logic)
No. 2 injector assembly Does not come on DTC stored SAE Code: P168B
P168B46 Injector #2 Internal EEPROM Calibration / Parameter Memory Failure A malfunction is continuously detected in the EEPROM (i-ART learning value) built into the No. 2 injector assembly for 3 seconds or more.
(1 trip detection logic)
No. 2 injector assembly Does not come on DTC stored SAE Code: P168B
P168C00 Injector #3 Internal EEPROM Malfunction A malfunction is continuously detected in the EEPROM (fuel temperature calibration value) built into the No. 3 injector assembly for 3 seconds or more.
(1 trip detection logic)
No. 3 injector assembly Does not come on DTC stored SAE Code: P168C
P168C44 Injector #3 Internal EEPROM Data Memory Failure A malfunction is continuously detected in the EEPROM (fuel pressure calibration value) built into the No. 3 injector assembly for 3 seconds or more.
(1 trip detection logic)
No. 3 injector assembly Does not come on DTC stored SAE Code: P168C
P168C46 Injector #3 Internal EEPROM Calibration / Parameter Memory Failure A malfunction is continuously detected in the EEPROM (i-ART learning value) built into the No. 3 injector assembly for 3 seconds or more.
(1 trip detection logic)
No. 3 injector assembly Does not come on DTC stored SAE Code: P168C
P168D00 Injector #4 Internal EEPROM Malfunction A malfunction is continuously detected in the EEPROM (fuel temperature calibration value) built into the No. 4 injector assembly for 3 seconds or more.
(1 trip detection logic)
No. 4 injector assembly Does not come on DTC stored SAE Code: P168D
P168D44 Injector #4 Internal EEPROM Data Memory Failure A malfunction is continuously detected in the EEPROM (fuel pressure calibration value) built into the No. 4 injector assembly for 3 seconds or more.
(1 trip detection logic)
No. 4 injector assembly Does not come on DTC stored SAE Code: P168D
P168D46 Injector #4 Internal EEPROM Calibration / Parameter Memory Failure A malfunction is continuously detected in the EEPROM (i-ART learning value) built into the No. 4 injector assembly for 3 seconds or more.
(1 trip detection logic)
No. 4 injector assembly Does not come on DTC stored SAE Code: P168D

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P168A00
P168B00
P168C00
P168D00
Ignition switch ON for 3 minutes or more
P168A44
P168B44
P168C44
P168D44
P168A46
P168B46
P168C46
P168D46

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR DTCS OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.


d.

Turn the ignition switch off and wait for 30 seconds or more.


e.

Turn the ignition switch to ON for 3 minutes or more.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Read the DTCs.

Result:
Result Proceed to
DTC P168A00, P168B00, P168C00 and/or P168D00 is output A
DTC P168A44, P168B44, P168C44 and/or P168D44 is output
DTC P168A46, P168B46, P168C46 and/or P168D46 is output
No DTC is output B




A

2.REPLACE INJECTOR ASSEMBLY (RELEVANT CYLINDER)

B

2.REPLACE INJECTOR ASSEMBLY (RELEVANT CYLINDER)
a.

Replace the injector assembly of the cylinder relevant to the DTC.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL INJECTOR>REMOVAL

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new No. 1 injection pipe sub-assembly and a new No. 2 injection pipe sub-assembly.

·

Follow the procedure in the repair manual and temporarily install the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and No. 1 nozzle leakage pipe assembly pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

3.BLEED AIR FROM FUEL SYSTEM
3.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTC.


d.

Turn the ignition switch off and wait for 30 seconds or more.


e.

Turn the ignition switch to ON for 3 minutes or more.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END