Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0442647 ECD SYSTEM(w/ DPF) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P054411  Exhaust Gas Temperature Sensor 1 Bank 1 Circuit Short to Ground  P054415  Exhaust Gas Temperature Sensor 1 Bank 1 Circuit Short to Battery or Open  


DESCRIPTION

A243953E17
5.719,4.677 5.875,4.677 false 1.76,5.427 1.875,5.427 false 1.729,2.51 1.125,2.958 true 1.583,1.75 1.219,1.042 1.219,1.042 1.125,1.042 true 2.24,1.271 2.854,0.229 2.854,0.229 4,0.229 false 2.417,2.896 3.844,3.313 3.844,3.313 4.042,3.313 true 2.479,2.083 4.313,2.417 4.313,2.417 4.542,2.417 true 4.146,0.146 6.271,0.458 2.125,0.313 10 false Exhaust Gas Temperature Sensor 1.521,0.542 2.365,0.719 0.844,0.177 10 false Exhaust Gas 3.167,0.927 3.531,1.094 0.365,0.167 10 false ECM 0.219,2.906 1.208,3.24 0.99,0.333 10 false DPF Catalytic Converter 4.604,2.344 7.094,2.688 2.49,0.344 10 false No. 2 Exhaust Gas Temperature Sensor 0.271,3.594 2.01,3.781 1.74,0.188 10 false Property of Output Voltage: 0.167,3.958 2.198,4.156 2.031,0.198 10 false Exhaust Gas Temperature (°C) 1.26,4.25 2.063,4.417 0.802,0.167 10 false 1000 1.323,4.417 2.021,4.583 0.698,0.167 10 false 960 1.323,4.646 2.021,4.813 0.698,0.167 10 false 760 1.323,4.875 2.021,5.042 0.698,0.167 10 false 560 1.323,5.104 1.948,5.271 0.625,0.167 10 false 360 1.323,5.344 1.958,5.51 0.635,0.167 10 false 160 1.333,5.604 1.917,5.771 0.583,0.167 10 false -40 1.573,5.688 1.677,5.875 0.104,0.188 10 false 0 1.729,5.688 1.948,5.875 0.219,0.188 10 false 0.2 1.99,5.688 2.229,5.875 0.24,0.188 10 false 0.5 2.396,5.688 2.635,5.875 0.24,0.188 10 false 1.0 2.844,5.688 3.083,5.875 0.24,0.188 10 false 1.5 3.271,5.688 3.51,5.875 0.24,0.188 10 false 2.0 3.719,5.688 3.958,5.875 0.24,0.188 10 false 2.5 4.177,5.688 4.417,5.875 0.24,0.188 10 false 3.0 4.615,5.688 4.948,5.938 0.333,0.25 10 false 3.5 5.031,5.688 5.458,5.969 0.427,0.281 10 false 4.0 5.458,5.688 5.677,5.875 0.219,0.188 10 false 4.5 5.708,5.688 6.021,5.875 0.313,0.188 10 false 4.95 6.021,5.688 6.25,5.875 0.229,0.188 10 false 5.0 2.635,6.104 5.51,6.313 2.875,0.208 10 false Exhaust Gas Temperature Sensor Voltage (V) 2,5.354 4.729,5.573 2.729,0.219 10 false Stores P054411, P203111 or P242A11 4.115,3.219 6.729,3.594 2.615,0.375 10 false No. 3 Exhaust Gas Temperature Sensor 0.24,0.958 1.229,1.292 0.99,0.333 10 false DOC Catalytic Converter 3.229,4.615 5.958,4.833 2.729,0.219 10 false Stores P054415, P203115 or P242A15

The exhaust gas temperature sensors are installed before and after the exhaust manifold converter sub-assembly to sense the exhaust gas temperature.

A thermistor built into the sensor changes its resistance value according to the exhaust gas temperature. The lower the exhaust gas temperature, the higher the thermistor resistance value. The higher the exhaust gas temperature, the lower the thermistor resistance value.

The exhaust gas temperature sensor is powered by a 5 V supply from the THTO, THCI and THCO terminals of the ECM, via resistor R.

Resistor R and the exhaust gas temperature sensor are connected in series. When the resistance value of the exhaust gas temperature sensor changes in accordance with the exhaust gas temperature, the voltage at terminals THTO, THCI and THCO also changes. The exhaust gas temperature sensor monitors the temperature upstream of the DOC catalyst. The No. 2 exhaust gas temperature sensor monitors the temperature upstream of the DPF catalyst. The No. 3 exhaust gas temperature sensor monitors the rise in temperature of the DPF catalyst. When PM forced regeneration is needed, the ECM operates the exhaust fuel addition injector assembly to obtain the target upstream temperature of the DPF catalytic converter as monitored through sensor 2. In addition, the ECM monitors the temperature increase of the exhaust manifold converter sub-assembly using sensor 3.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P054411 Exhaust Gas Temperature Sensor 1 Bank 1 Circuit Short to Ground Exhaust gas temperature sensor output voltage is below 0.2 V for 3 seconds or more.
(1 trip detection logic)
·

Open or short in exhaust gas temperature sensor circuit

·

Exhaust gas temperature sensor

·

ECM


Comes on DTC stored SAE Code: P0545
P054415 Exhaust Gas Temperature Sensor 1 Bank 1 Circuit Short to Battery or Open Exhaust gas temperature sensor output voltage is higher than 4.95 V for 3 seconds or more when all conditions are met:
·

After starting the engine, 11 minutes or more elapses

·

Engine is running

·

Coolant temperature is 60°C (140°F) or higher


(1 trip detection logic)
·

Open or short in exhaust gas temperature sensor circuit

·

Exhaust gas temperature sensor

·

ECM


Comes on DTC stored SAE Code: P0546

Related Data List
DTC No. Data List
P054411
P054415
Exhaust Temperature B1S1

HINT:
·

DTC P20CF00 (Exhaust fuel addition injector assembly malfunction) may be stored if there is an open malfunction in an exhaust gas temperature sensor circuit.

·

Sensor 1 represents the sensor located upstream of the DOC catalytic converter.

·

When DTC P054411 and P054415 is output, check the exhaust gas temperature indicated by "Powertrain / Engine / Data List / Diesel Exhaust / Exhaust Temperature B1S1" using the GTS.


Reference:
Condition Exhaust Temperature B1S1 Exhaust Gas Temperature Sensor Condition
Idling with warm engine Constant at between 50 and 450°C (122 and 842°F) Normal
0°C (32°F) Open circuit
1000°C (1832°F) Short circuit


MONITOR DESCRIPTION

The ECM constantly monitors the output voltages from the exhaust gas temperature sensors in order to detect problems with the sensors. When the sensor output voltage deviates from the normal operating range (between 0.2 V and 4.95 V) for more than 3 seconds after the engine is warmed up, the ECM interprets this as malfunction of the sensor circuit and illuminates the MIL.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P054411 Engine switch on (IG) for 3 seconds or more
P054415 Idle the engine for 3 seconds after warming up the engine (the engine coolant temperature is 60°C (140°F) or higher) and allowing 11 minutes to elapse after starting the engine.

WIRING DIAGRAM

A444427E09
1.917,0.906 4.167,1.26 2.25,0.354 10 false Exhaust Gas Temperature Sensor 1.917,0.74 2.531,0.938 0.615,0.198 10 false C169 5.708,1.49 6.323,1.688 0.615,0.198 10 false THCI 5.448,0.51 6.063,0.708 0.615,0.198 10 false 23 3.25,0.26 3.865,0.458 0.615,0.198 10 false THC3 2.313,0.271 2.927,0.469 0.615,0.198 10 false E2 3.719,0.5 4.333,0.698 0.615,0.198 10 false 2 2.146,0.5 2.76,0.698 0.615,0.198 10 false 1 2.146,1.635 2.76,1.833 0.615,0.198 10 false 1 3.708,1.635 4.323,1.833 0.615,0.198 10 false 2 3.698,2.781 4.313,2.979 0.615,0.198 10 false 2 2.146,2.792 2.76,2.99 0.615,0.198 10 false 1 2.302,1.385 2.917,1.583 0.615,0.198 10 false E2 3.281,1.396 3.896,1.594 0.615,0.198 10 false THCI 3.219,2.563 3.833,2.76 0.615,0.198 10 false THCO 2.313,2.563 2.927,2.76 0.615,0.198 10 false E2 5.688,3.74 6.302,3.938 0.615,0.198 10 false E2 5.438,1.635 6.052,1.833 0.615,0.198 10 false 25 5.448,2.802 6.063,3 0.615,0.198 10 false 33 5.438,3.875 6.052,4.073 0.615,0.198 10 false 27 1.979,1.844 2.594,2.042 0.615,0.198 10 false C166 1.99,2.01 4.698,2.26 2.708,0.25 10 false No. 2 Exhaust Gas Temperature Sensor 2.052,3.229 4.76,3.479 2.708,0.25 10 false No. 3 Exhaust Gas Temperature Sensor 2.042,3.063 2.656,3.26 0.615,0.198 10 false C167 6.073,4.208 6.688,4.406 0.615,0.198 10 false C149 6.073,4.396 6.688,4.594 0.615,0.198 10 false ECM 5.719,0.375 6.333,0.573 0.615,0.198 10 false THTO 5.708,2.667 6.323,2.865 0.615,0.198 10 false THCO

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (EXHAUST TEMPERATURE B1S1)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Diesel Exhaust / Exhaust Temperature B1S1.


d.

Read the value.

Standard:

Same as the actual exhaust gas temperature (50 to 450°C [122 to 842°F] during idling with warm engine), and varies after an engine speed of 3000 rpm is maintained for 1 minute.


Result:
Temperature Displayed Proceed to
0°C (32°F) (After warming up the engine) A
1000°C (1832°F) or higher B
Same as the actual exhaust gas temperature C


HINT:
·

If there is a short circuit, the GTS will indicate 0°C (32°F).

·

If there is an open circuit, the GTS will indicate 1000°C (1832°F).





A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

8.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

C

14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.
A356525C43
1.479,2.719 1.927,3.052 0.448,0.333 1.406,4.052 1.615,3.583 true 2.031,4.042 1.813,3.583 true 0.563,2.76 0.875,2.958 0.313,0.198 10 false *a 0.688,1.802 1,2 0.313,0.198 10 false *1 2.583,1.771 2.896,1.969 0.313,0.198 10 false *2 1.542,2.813 1.99,3.031 0.448,0.219 10 false C169 1.292,4.083 1.74,4.281 0.448,0.198 10 false E2 2,4.083 2.417,4.271 0.417,0.188 10 false THC3 1.531,0.656 1.948,0.844 0.417,0.188 10 false THC3 1.625,1.354 2.073,1.552 0.448,0.198 10 false E2
*1 Exhaust Gas Temperature Sensor
*2 ECM
*a Front view of wire harness connector
(to Exhaust Gas Temperature Sensor)


Disconnect the exhaust gas temperature sensor connector.


b.

Connect terminals 1 (E2) and 2 (THC3) of the exhaust gas temperature sensor connector on the wire harness side.


c.

Connect the GTS to the DLC3.


d.

Turn the engine switch on (IG) and turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Data List / Diesel Exhaust / Exhaust Temperature B1S1.


f.

Read the value.

Standard:

1000°C (1832°F)



Result:
Proceed to
OK
NG



OK

3.REPLACE EXHAUST GAS TEMPERATURE SENSOR

NG

4.CHECK HARNESS AND CONNECTOR (EXHAUST GAS TEMPERATURE SENSOR - ECM)
3.REPLACE EXHAUST GAS TEMPERATURE SENSOR

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CHECK HARNESS AND CONNECTOR (EXHAUST GAS TEMPERATURE SENSOR - ECM)
a.

Disconnect the exhaust gas temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C169-2 (THC3) - C149-23 (THTO) Always Below 1 Ω
C169-1 (E2) - C149-27 (E2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.REPLACE ECM

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Clear the DTCs.


d.

Turn the engine switch off and wait for 30 seconds or more.


e.

Start the engine and turn the GTS on.


f.

Idle the engine for 3 seconds or more after warming up the engine (the engine coolant temperature is 60°C (140°F) or higher) and allowing 11 minutes to elapse after starting the engine.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output.


Result:
Proceed to
NEXT



NEXT

END

8.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
a.
A178587C05
0.792,1.594 1.104,1.792 0.313,0.198 10 false *1 2.698,1.677 3.01,1.875 0.313,0.198 10 false *2
*1 Exhaust Gas Temperature Sensor
*2 ECM


Disconnect the exhaust gas temperature sensor connector.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG) and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Exhaust Temperature B1S1.


e.

Read the value.

Standard:

0°C (32°F)



Result:
Proceed to
OK
NG



OK

9.REPLACE EXHAUST GAS TEMPERATURE SENSOR

NG

10.CHECK HARNESS AND CONNECTOR (EXHAUST GAS TEMPERATURE SENSOR - ECM)
9.REPLACE EXHAUST GAS TEMPERATURE SENSOR

Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.CHECK HARNESS AND CONNECTOR (EXHAUST GAS TEMPERATURE SENSOR - ECM)
a.

Disconnect the exhaust gas temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C169-2 (THC3) or C149-23 (THTO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.REPLACE ECM

NG

12.REPAIR OR REPLACE HARNESS OR CONNECTOR
11.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Clear the DTCs.


d.

Turn the engine switch off and wait for 30 seconds or more.


e.

Turn the engine switch on (IG) for 3 seconds or more.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Confirm that the DTC is not output.


Result:
Proceed to
NEXT



NEXT

END

14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Clear the DTCs.


d.

Turn the engine switch off and wait for 30 seconds or more.


e.

Turn the engine switch on (IG) for 3 seconds or more.


f.

Turn the GTS on.


g.

Start the engine.


h.

Idle the engine for 3 seconds or more after warming up the engine (the engine coolant temperature is 60°C (140°F) or higher) and allowing 11 minutes to elapse after starting the engine.


i.

Enter the following menus: Powertrain / Engine / Trouble Codes.


j.

Confirm that the DTC is not output.


Result:
Proceed to
NEXT



NEXT

END