Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0442647 ECD SYSTEM(w/ DPF) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P0A1412  Engine Mount "A" Control Circuit High Circuit Short to Battery  P0A1414  Engine Mount "A" Control Circuit Low Circuit Short to Ground or Open  


DESCRIPTION

The active control engine mount system decreases engine vibration at low engine speed using the vacuum switching valve sub-assembly (for engine mounting). The vacuum switching valve sub-assembly (for engine mounting) is controlled by a pulse signal transmitted to the vacuum switching valve sub-assembly (for engine mounting) from the ECM. The frequency of this pulse signal is matched to the engine speed to decrease engine vibration.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P0A1412 Engine Mount "A" Control Circuit High Circuit Short to Battery Short in vacuum switching valve sub-assembly (for engine mounting)circuit and power supply circuit (2 trip detection logic).
·

Short in vacuum switching valve sub-assembly (for engine mounting)circuit

·

Vacuum switching valve sub-assembly (for engine mounting)

·

ECM


Does not come on DTC stored SAE: P0A16
P0A1414 Engine Mount "A" Control Circuit Low Circuit Short to Ground or Open Open or short in vacuum switching valve sub-assembly (for engine mounting)circuit and power supply circuit
(2 trip detection logic).
·

Open or short in vacuum switching valve sub-assembly (for engine mounting)circuit

·

Vacuum switching valve sub-assembly (for engine mounting)

·

ECM


Does not come on DTC stored SAE: P0A15

MONITOR DESCRIPTION

The ECM monitors the output voltage while the vacuum switching valve sub-assembly (for engine mounting)is operating.

The vacuum switching valve sub-assembly (for engine mounting)turns on and off according to ON/OFF switching of a transistor inside the ECM.

If a continuous mismatch occurs between the ECM transistor state and the output voltage, the ECM determines there is a malfunction in the vacuum switching valve sub-assembly (for engine mounting)circuit and stores a DTC.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0A1412
P0A1414
Engine switch on (IG) for 3 seconds or more

WIRING DIAGRAM

A474994E11
2.698,1.135 5.167,1.729 2.469,0.594 10 false Vacuum Switching Valve Sub-Assembly (for Engine Mounting) 2.698,0.99 3.313,1.188 0.615,0.198 10 false C173 1.854,0.802 3.229,1 1.375,0.198 10 false EFI NO. 2 1.854,0.521 2.01,0.719 0.156,0.198 10 false 1 2.302,0.51 2.458,0.708 0.156,0.198 10 false 2 6.302,0.667 6.917,0.865 0.615,0.198 10 false ACM 5.844,0.646 6.458,0.844 0.615,0.198 10 false G184 4.51,0.49 4.667,0.688 0.156,0.198 10 false 2 3.104,0.5 3.26,0.698 0.156,0.198 10 false 1 5.917,0.458 6.156,0.656 0.24,0.198 10 false 34 4.281,2.813 4.896,3.01 0.615,0.198 10 false 1W 4.354,2.646 4.51,2.844 0.156,0.198 10 false 3 2.469,2.708 2.625,2.906 0.156,0.198 10 false 2 2.031,2.698 2.188,2.896 0.156,0.198 10 false 1 2.938,3.552 4.313,3.75 1.375,0.198 10 false EFI MAIN NO. 2 1.813,4.146 3.188,4.344 1.375,0.198 10 false EFI MAIN NO. 1 1.823,2.958 3.198,3.156 1.375,0.198 10 false EFI MAIN NO. 2 2.99,4.76 4.365,4.958 1.375,0.198 10 false EFI MAIN NO. 1 4.281,3.219 4.896,3.417 0.615,0.198 10 false 1W 4.354,3.042 4.51,3.24 0.156,0.198 10 false 2 4.313,3.979 4.927,4.177 0.615,0.198 10 false 1V 4.313,4.406 4.927,4.604 0.615,0.198 10 false 1V 5.844,4.396 6.458,4.594 0.615,0.198 10 false G184 5.938,4.229 6.208,4.427 0.271,0.198 10 false 14 1.323,2.813 1.938,3.01 0.615,0.198 10 false 1S 1.292,3.219 1.906,3.417 0.615,0.198 10 false 1W 4.365,3.781 4.521,3.979 0.156,0.198 10 false 6 4.354,4.24 4.51,4.438 0.156,0.198 10 false 7 4.948,3.635 6.323,3.833 1.375,0.198 10 false EFI MAIN NO. 3 1.365,2.635 1.979,2.833 0.615,0.198 10 false 1 1.365,3.052 1.521,3.25 0.156,0.198 10 false 4 6.479,5.292 7.01,5.604 0.531,0.313 10 false ECM 0.417,4.063 1.792,4.26 1.375,0.198 10 false 70A FL 0.594,5.719 1.969,5.917 1.375,0.198 10 false Battry 2.104,5.24 3.896,5.5 1.792,0.26 10 false No. 1 Integration Relay 6.323,4.302 6.938,4.5 0.615,0.198 10 false MREL

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT VACUUM SWITCHING VALVE SUB-ASSEMBLY (FOR ENGINE MOUNTING) (RESISTANCE)
a.

Inspect the vacuum switching valve sub-assembly (for engine mounting).

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>VACUUM SWITCHING VALVE (for Engine Mounting)>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK VACUUM SWITCHING VALVE SUB-ASSEMBLY (FOR ENGINE MOUNTING) (POWER SOURCE CIRCUIT)

NG

7.REPLACE VACUUM SWITCHING VALVE SUB-ASSEMBLY (FOR ENGINE MOUNTING)
2.CHECK VACUUM SWITCHING VALVE SUB-ASSEMBLY (FOR ENGINE MOUNTING) (POWER SOURCE CIRCUIT)
a.

Disconnect the vacuum switching valve sub-assembly (for engine mounting) connector.


b.
A249191C18
1.448,0.094 1.969,0.417 0.521,0.323 0.281,0.302 0.594,0.5 0.313,0.198 10 false *a 1.5,0.188 2.115,0.385 0.615,0.198 10 false C173
*a Front view of wire harness connector
(to Vacuum Switching Valve Sub-assembly (for Engine Mounting))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C173-1 - Body ground Engine switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE ASSEMBLY SUB-ASSEMBLY (FOR ENGINE MOUNTING) - ECM)

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE ASSEMBLY SUB-ASSEMBLY (FOR ENGINE MOUNTING) - ECM)
a.

Disconnect the vacuum switching valve sub-assembly (for engine mounting) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C173-2 - G184-34 (ACM) Always Below 1 Ω
C173-2 or G184-34 (ACM) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.

HINT:

If the voltage at the vacuum switching valve sub-assembly (for engine mounting) connector is not 11 to 14 V, repair or replace the harness and connector between the vacuum switching valve sub-assembly (for engine mounting) and No. 1 integration relay.



Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.


c.

Turn the engine switch on (IG) for 3 seconds or more.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

7.REPLACE VACUUM SWITCHING VALVE SUB-ASSEMBLY (FOR ENGINE MOUNTING)
a.

Replace the vacuum switching valve sub-assembly (for engine mounting).

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>VACUUM SWITCHING VALVE (for Engine Mounting)>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED