Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0442647 ECD SYSTEM(w/ DPF) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P212012  Throttle/Pedal Position Sensor/Switch "D" Circuit Short to Auxiliary Battery  P212014  Throttle/Pedal Position Sensor/Switch "D" Circuit Short to Ground or Open  P21201C  Throttle/Pedal Position Sensor/Switch "D" Circuit Voltage Out of Range  P21201F  Throttle/Pedal Position Sensor/Switch "D" Circuit Intermittent  P212099  Throttle/Pedal Position Sensor/Switch "D" Exceeded Learning Limit  P212512  Throttle/Pedal Position Sensor/Switch "E" Circuit Short to Auxiliary Battery  P212514  Throttle/Pedal Position Sensor/Switch "E" Circuit Short to Ground or Open  P21251F  Throttle/Pedal Position Sensor/Switch "E" Circuit Intermittent  P21382B  Throttle/Pedal Position Sensor/Switch "D"/"E" Signal Cross Coupled  


DESCRIPTION

HINT:
·

This is the repair procedure for the accelerator pedal sensor assembly.

·

This electrical throttle system does not use a throttle cable.

·

This accelerator pedal position sensor is a non-contact type.



The accelerator pedal position sensor is mounted on the accelerator pedal sensor assembly and detects the opening angle of the accelerator pedal. Since this sensor is electronically controlled with Hall-effect elements, accurate control and reliability can be obtained. It has 2 sensors to detect the accelerator position and a malfunction of the accelerator pedal position sensor.

In the accelerator pedal position sensor, the voltage applied to terminals VPA and VPA2 of the ECM changes between 0.5 V and 4.8 V in proportion to the opening angle of the accelerator pedal. The VPA is a signal to indicate the actual accelerator pedal opening angle which is used for engine control, and the VPA2 is a signal to indicate information about the opening angle which is used for detecting malfunctions. The ECM judges the current opening angle of the accelerator pedal using signals from terminals VPA and VPA2, and the ECM controls the injection volume based on these signals.

A255815E39
4.333,2.031 4.208,1.948 false 4.323,2.198 4.208,2.146 false 4.344,2.24 4.229,2.333 false 4.344,2.396 4.229,2.51 false 4.344,2.917 4.219,2.917 false 4.354,3.125 4.208,3.125 false 0.854,2.875 0.5,3.333 true 1.052,2.26 1.302,1.375 1.302,1.375 1.417,1.375 true 4.333,1.833 3.844,0.938 false 1.021,2.542 0.927,1.844 0.927,1.844 0.844,1.844 true 0.552,3.802 1.708,4.135 1.156,0.333 10 false Accelerator Pedal Position Sensor 1.458,1.302 1.938,1.479 0.479,0.177 10 false Magnet 0.313,1.76 0.844,1.938 0.531,0.177 10 false IC No. 1 0.313,3.344 0.844,3.521 0.531,0.177 10 false IC No. 2 2.063,1.74 2.531,1.917 0.469,0.177 10 false VPA 2.063,2.073 2.552,2.271 0.49,0.198 10 false EPA 2.063,2.385 2.583,2.563 0.521,0.177 10 false VCPA 2.063,2.688 2.573,2.865 0.51,0.177 10 false VPA2 2.063,3 2.563,3.198 0.5,0.198 10 false EPA2 2.063,3.323 2.583,3.5 0.521,0.177 10 false VCP2 2.677,3.76 3,3.938 0.323,0.177 10 false ECM 4.271,1.542 4.427,1.719 0.156,0.177 10 false *1 5.865,1.542 6.021,1.719 0.156,0.177 10 false *2 3.917,1.854 4.208,2.031 0.292,0.177 10 false 4.55 3.844,2.063 4.208,2.24 0.365,0.177 10 false 3.988 3.938,2.281 4.229,2.458 0.292,0.177 10 false 3.75 3.875,2.469 4.24,2.646 0.365,0.177 10 false 3.188 3.969,2.823 4.271,3 0.302,0.177 10 false 1.6 3.979,3.042 4.281,3.219 0.302,0.177 10 false 0.8 4.406,3.344 4.698,3.521 0.292,0.177 10 false 0.29 4.26,3.594 4.417,3.771 0.156,0.177 10 false 0 5.781,3.594 6.073,3.771 0.292,0.177 10 false 13.1 4.677,3.583 5.604,3.823 0.927,0.24 10 false Usable Range 4.656,3.938 6.76,4.167 2.104,0.229 10 false Accelerator Pedal Angle (°) 4.344,4.656 6.625,4.833 2.281,0.177 10 false *1: Accelerator Pedal Fully Released 4.344,4.969 6.729,5.135 2.385,0.167 10 false *2: Accelerator Pedal Fully Depressed 2.156,0.813 3.854,1.167 1.698,0.354 10 false Accelerator Pedal Position Sensor Output Voltage (V) 6.479,2.281 6.927,2.51 0.448,0.229 10 false VPA 6.438,1.823 6.865,2 0.427,0.177 10 false VPA2

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P212012 Throttle/Pedal Position Sensor/Switch "D" Circuit Short to Auxiliary Battery VPA is 4.8 V or higher for 2 seconds or more.
(1 trip detection logic)
·

Accelerator pedal sensor assembly

·

Open in EPA circuit

·

Short in VPA circuit

·

ECM


Comes on DTC stored SAE Code: P2123
P212014 Throttle/Pedal Position Sensor/Switch "D" Circuit Short to Ground or Open VPA is 0.4 V or less for 0.5 seconds or more when the accelerator pedal is depressed.
(1 trip detection logic)
·

Accelerator pedal sensor assembly

·

Open in VCPA circuit

·

VPA circuit open or shorted to ground

·

ECM


Comes on DTC stored SAE Code: P2122
P21201C Throttle/Pedal Position Sensor/Switch "D" Circuit Voltage Out of Range Difference between VPA and VPA2 is greater than or equal to the specified value for 2 seconds.
(1 trip detection logic)
·

Accelerator pedal sensor assembly

·

ECM


Comes on DTC stored SAE Code: P2121
P21201F Throttle/Pedal Position Sensor/Switch "D" Circuit Intermittent VPA fluctuates rapidly beyond the upper and lower malfunction thresholds for 0.5 seconds or more.
(1 trip detection logic)
·

Accelerator pedal sensor assembly

·

Accelerator pedal sensor assembly circuit

·

ECM


Comes on DTC stored SAE Code: P2120
P212099 Throttle/Pedal Position Sensor/Switch "D" Exceeded Learning Limit Difference between VPA and VPA2 is less than 0.4 V, or higher than 1.2 V (learned value of accelerator off position).
(1 trip detection logic)
·

Accelerator pedal sensor assembly

·

ECM


Comes on DTC stored SAE Code: P2121
P212512 Throttle/Pedal Position Sensor/Switch "E" Circuit Short to Auxiliary Battery Both of the following conditions are met for 2 seconds or more:
(a) VPA2 is 4.8 V or higher.
(b) VPA is between 0.4 V and 3.45 V.
(1 trip detection logic)
·

Accelerator pedal sensor assembly

·

Open in EPA2 circuit

·

Short in VPA2 circuit

·

ECM


Comes on DTC stored SAE Code: P2128
P212514 Throttle/Pedal Position Sensor/Switch "E" Circuit Short to Ground or Open VPA2 is 1.2 V or less for 0.5 seconds or more when the accelerator pedal is depressed.
(1 trip detection logic)
·

Accelerator pedal sensor assembly

·

Open in VCP2 circuit

·

VPA2 circuit open or shorted to ground

·

ECM


Comes on DTC stored SAE Code: P2127
P21251F Throttle/Pedal Position Sensor/Switch "E" Circuit Intermittent VPA2 fluctuates rapidly beyond the upper and lower malfunction thresholds for 0.5 seconds or more.
(1 trip detection logic)
·

Accelerator pedal sensor assembly

·

Accelerator pedal sensor assembly circuit

·

ECM


Comes on DTC stored SAE Code: P2125
P21382B Throttle/Pedal Position Sensor/Switch "D"/"E" Signal Cross Coupled Difference between VPA and VPA2 is 0.02 V or less for 2.0 seconds or more.
(1 trip detection logic)
·

Accelerator pedal sensor assembly

·

Accelerator pedal sensor assembly circuit

·

ECM


Comes on DTC stored SAE Code: P2138

Related Data List
DTC No. Data List
P212012
P212014
P21201C
P21201F
P212099
P212512
P212514
P21251F
P21382B
·

Accel Position

·

Accelerator Position Sensor No.1 Voltage %

·

Accelerator Position Sensor No.2 Voltage %



CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P212012
P212014
P21201C
P21201F
P212099
P212512
P212514
P21251F
P21382B
Engine switch on (IG)
·

Accelerator pedal fully released for 3 seconds

·

Accelerator pedal depressed partway for 3 seconds

·

Accelerator pedal fully depressed for 3 seconds



WIRING DIAGRAM

A348544E28
0.396,3.052 0.854,3.25 0.458,0.198 10 false A19 0.375,3.229 3.177,3.583 2.802,0.354 10 false Accelerator Pedal Position Sensor (Accelerator Pedal Sensor Assembly) 5.906,3.073 6.365,3.271 0.458,0.198 10 false G185 5.906,3.24 6.365,3.438 0.458,0.198 10 false ECM 1.604,0.542 2.063,0.74 0.458,0.198 10 false VPA 1.594,0.969 2.052,1.167 0.458,0.198 10 false EPA 1.51,1.396 2.219,1.615 0.708,0.219 10 false VCPA 1.531,1.802 1.99,2 0.458,0.198 10 false VPA2 1.531,2.219 1.99,2.417 0.458,0.198 10 false EPA2 1.531,2.635 1.99,2.833 0.458,0.198 10 false VCP2 2,2.74 2.458,2.938 0.458,0.198 10 false 1 2,2.333 2.458,2.531 0.458,0.198 10 false 2 2.01,1.927 2.469,2.125 0.458,0.198 10 false 3 2.01,1.479 2.469,1.677 0.458,0.198 10 false 4 2.01,1.083 2.469,1.281 0.458,0.198 10 false 5 1.99,0.656 2.448,0.854 0.458,0.198 10 false 6 5.333,0.646 5.792,0.844 0.458,0.198 10 false 28 5.323,1.073 5.781,1.271 0.458,0.198 10 false 22 5.333,1.5 5.792,1.698 0.458,0.198 10 false 29 5.333,1.917 5.792,2.115 0.458,0.198 10 false 31 5.333,2.333 5.792,2.531 0.458,0.198 10 false 25 5.333,2.75 5.792,2.948 0.458,0.198 10 false 30 5.615,2.521 6.073,2.719 0.458,0.198 10 false VCP2 5.583,2.094 6.042,2.292 0.458,0.198 10 false EPA2 5.594,1.667 6.052,1.865 0.458,0.198 10 false VPA2 5.594,1.229 6.302,1.448 0.708,0.219 10 false VCPA 5.594,0.833 6.052,1.031 0.458,0.198 10 false EPA 5.615,0.417 6.073,0.615 0.458,0.198 10 false VPA

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (ACCELERATOR POSITION SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Primary / Accelerator Position Sensor No.1 Voltage % and Accelerator Position Sensor No.2 Voltage %.


d.
C129061C03
0.833,1.594 1.042,1.802 0.208,0.208 10 false *a 0.271,0.323 0.479,0.531 0.208,0.208 10 false *1 2.24,1.594 2.5,1.802 0.26,0.208 10 false *b
*1 Accelerator Pedal Sensor Assembly
*a Depressed
*b Released


Read the values.

Standard:
Accelerator Pedal Accelerator Position Sensor No.1 Voltage % Accelerator Position Sensor No.2 Voltage %
Released 10 to 22% 24 to 40%
Depressed 52 to 90% 68 to 99%



Result:
Result Proceed to
NG A
OK B



A

2.CHECK ECM (ACCELERATOR PEDAL POSITION SENSOR VOLTAGE)

B

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.CHECK ECM (ACCELERATOR PEDAL POSITION SENSOR VOLTAGE)
a.
A460802C43
2.708,0.833 3.125,1.083 0.417,0.25 2.344,2.302 2.875,1.698 true 3,2.323 3,1.708 true 1.708,2.302 2.823,1.646 true 3.042,1.625 2.323,1.031 2.323,1.031 2.146,1.031 true 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a 2.76,0.875 3.219,1.073 0.458,0.198 10 false G185 1.125,2.396 1.865,2.625 0.74,0.229 10 false 25 (EPA2) 1.927,2.406 2.667,2.594 0.74,0.188 10 false 30 (VCP2) 2.656,2.396 3.385,2.583 0.729,0.188 10 false 29 (VCPA) 1.5,0.969 2.229,1.177 0.729,0.208 10 false 22 (EPA)
*a Component with harness connected
(ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G151-29 (VCPA) - G151-22 (EPA) Engine switch on (IG) 4.5 to 5.5 V
G151-30 (VCP2) - G151-25 (EPA2) Engine switch on (IG) 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

3.INSPECT ACCELERATOR PEDAL POSITION SENSOR (VPA, VPA2 VOLTAGE)

NG

10.REPLACE ECM
3.INSPECT ACCELERATOR PEDAL POSITION SENSOR (VPA, VPA2 VOLTAGE)
a.
A460802C44
2.708,0.833 3.125,1.083 0.417,0.25 2.344,2.302 2.833,1.698 true 3,2.323 3.042,1.688 true 1.708,2.302 2.823,1.646 true 3.042,1.625 2.323,1.031 2.323,1.031 2.146,1.031 true 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a 2.76,0.875 3.219,1.073 0.458,0.198 10 false G185 1.125,2.396 1.865,2.625 0.74,0.229 10 false 25 (EPA2) 1.927,2.406 2.667,2.594 0.74,0.188 10 false 31 (VPA2) 2.688,2.396 3.417,2.583 0.729,0.188 10 false 28 (VPA) 1.5,0.969 2.229,1.177 0.729,0.208 10 false 22 (EPA)
*a Component with harness connected
(ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G185-28 (VPA) - G185-22 (EPA) Engine switch on (IG), accelerator pedal fully released 0.5 to 1.1 V
Engine switch on (IG), accelerator pedal fully depressed 3.0 to 4.6 V
G185-31 (VPA2) - G185-25 (EPA2) Engine switch on (IG), accelerator pedal fully released 0.9 to 2.3 V
Engine switch on (IG), accelerator pedal fully depressed 3.4 to 5.0 V



Result:
Proceed to
OK
NG



OK

10.REPLACE ECM

NG

4.INSPECT ECM TERMINAL VOLTAGE (VCPA AND VCP2 TERMINALS)
4.INSPECT ECM TERMINAL VOLTAGE (VCPA AND VCP2 TERMINALS)
a.

Disconnect the accelerator pedal sensor assembly connector.


b.
A449481C06
0.25,2.188 0.729,2.5 0.479,0.313 0.948,3.094 1.417,2.458 true 1.281,2.438 0.771,2.823 true 2.01,3.115 1.885,2.469 true 1.729,2.458 1.542,3.115 true 0.219,0.188 0.76,0.552 0.542,0.365 10 false *a 1.938,3.125 2.521,3.427 0.583,0.302 10 false EPA 0.688,3.125 1.365,3.427 0.677,0.302 10 false EPA2 0.375,2.781 1.031,3.104 0.656,0.323 10 false VCP2 1.323,3.125 1.927,3.427 0.604,0.302 10 false VCPA 0.365,2.26 0.688,2.521 0.323,0.26 10 false A19
*a Front view of wire harness connector
(to Accelerator Pedal Sensor Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A19-4 (VCPA) - A19-5 (EPA) Engine switch on (IG) 4.5 to 5.5 V
A19-1 (VCP2) - A19-2 (EPA2) Engine switch on (IG) 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL SENSOR ASSEMBLY - ECM)

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL SENSOR ASSEMBLY - ECM)
a.

Disconnect the accelerator pedal sensor assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A19-6 (VPA) - G185-28 (VPA) Always Below 1 Ω
A19-5 (EPA) - G185-22 (EPA) Always Below 1 Ω
A19-3 (VPA2) - G185-31 (VPA2) Always Below 1 Ω
A19-2 (EPA2) - G185-25 (EPA2) Always Below 1 Ω
A19-6 (VPA) or G185-28 (VPA) - Body ground and other terminals Always 10 kΩ or higher
A19-5 (EPA) or G185-22 (EPA) - Body ground and other terminals Always 10 kΩ or higher
A19-3 (VPA2) or G185-31 (VPA2) - Body ground and other terminals Always 10 kΩ or higher
A19-2 (EPA2) or G185-25 (EPA2) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK ECM (CHECK RESISTANCE)

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.CHECK ECM (CHECK RESISTANCE)
a.

Disconnect the accelerator pedal sensor assembly connector.


b.
A460802C45
2.76,0.833 3.177,1.083 0.417,0.25 2.063,2.354 2.875,1.688 true 2.635,2.354 3,1.708 true 1.354,2.344 2.823,1.688 true 3.052,1.635 2.406,0.76 2.406,0.76 2.208,0.76 true 3.073,2.677 3.042,1.688 true 2.823,1.635 2.396,1.073 2.396,1.073 2.219,1.073 true 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a 2.823,0.875 3.281,1.073 0.458,0.198 10 false G185 2.219,2.375 2.948,2.563 0.729,0.188 10 false 29 (VCPA) 1.594,0.698 2.323,0.906 0.729,0.208 10 false 22 (EPA) 2.74,2.76 3.354,2.958 0.615,0.198 10 false 28 (VPA) 1.438,2.375 2.219,2.583 0.781,0.208 10 false 30 (VCP2) 0.719,2.375 1.458,2.563 0.74,0.188 10 false 31 (VPA2) 1.51,0.99 2.229,1.198 0.719,0.208 10 false 25 (EPA2)
*a Component with harness connected
(ECM)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G185-29 (VCPA) - G185-28 (VPA) Engine switch off No short or no open circuit
G185-28 (VPA) - G185-22 (EPA) Engine switch off No short or no open circuit
G185-30 (VCP2) - G185-31 (VPA2) Engine switch off No short or no open circuit
G185-31 (VPA2) - G185-25 (EPA2) Engine switch off No short or no open circuit



Result:
Proceed to
OK
NG



OK

7.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

NG

10.REPLACE ECM
7.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY
a.

Replace the accelerator pedal sensor assembly.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ACCELERATOR PEDAL>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.


c.

Turn the engine switch off and leave the vehicle for 30 seconds.


d.

Turn the engine switch on (IG) and turn the GTS on.


e.

Fully release the accelerator pedal for 3 seconds or more, then depress it partway for 3 seconds or more, and then fully depress it for 3 seconds or more.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

10.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED