The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the fuel tank sub-assembly removal/installation are shown below.
When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
3.REMOVE REAR SEAT ASSEMBLY LH
for 60/40 Split Double-folding Seat Type LH Side:
for 60/40 Split Slide Walk-in Seat Type LH Side:
58371F
4.REMOVE REAR NO. 1 FLOOR STEP COVER (w/ Rear No. 2 Seat)
67934
5.REMOVE QUARTER SCUFF PLATE LH (w/ Rear No. 2 Seat)
67918D
6.REMOVE REAR DOOR SCUFF PLATE LH
58325E
7.REMOVE REAR FLOOR SERVICE HOLE COVER
Remove the 3 screws and rear floor service hole cover.
| *A | for Single Tank Type |
| *B | for Double Tank Type |
Disconnect the fuel pump and sender gauge connector.
77606
8.REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY
for Type A:
Remove the 6 bolts and No. 1 fuel tank protector sub-assembly.
for Type B:
Remove the 4 bolts and No. 1 fuel tank protector sub-assembly.
77209D
9.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY (for Single Tank Type)
Disconnect the fuel tank main tube sub-assembly (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>PRECAUTION).
77207A
10.DISCONNECT FUEL RETURN TUBE SUB-ASSEMBLY (for Single Tank Type)
Disconnect the fuel return tube sub-assembly (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>PRECAUTION).
77209D
11.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY (for Double Tank Type)
Disconnect fuel tank main tube sub-assembly (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>PRECAUTION).
12.DISCONNECT FUEL CUT OFF TUBE (for Single Tank Type)
Disconnect the fuel cut off tube (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>PRECAUTION).
77012
13.DISCONNECT FUEL TANK BREATHER TUBE SUB-ASSEMBLY (for Single Tank Type)
Disconnect the fuel tank breather tube sub-assembly (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>PRECAUTION).
77208A
14.DISCONNECT NO. 4 FUEL MAIN TUBE SUB-ASSEMBLY AND FUEL SUCTION TUBE SUB-ASSEMBLY (for Double Tank Type)
Disconnect the No. 4 fuel main tube sub-assembly and fuel suction tube sub-assembly (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>PRECAUTION).
15.DISCONNECT FUEL CUT OFF TUBE (for Double Tank Type)
Disconnect the fuel cut off tube (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>PRECAUTION).
77207A
16.DISCONNECT FUEL RETURN TUBE SUB-ASSEMBLY AND NO. 2 FUEL MAIN TUBE SUB-ASSEMBLY (for Double Tank Type)
Disconnect the fuel return tube sub-assembly and No. 2 fuel main tube sub-assembly (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>PRECAUTION).
77012
17.DISCONNECT FUEL TANK BREATHER TUBE SUB-ASSEMBLY (for Double Tank Type)
Disconnect the fuel tank breather tube sub-assembly (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>PRECAUTION).
77213B
18.DISCONNECT FUEL TANK TO FILLER PIPE HOSE
Loosen the clamp and disconnect the fuel tank to filler pipe hose from the filler pipe.
77100U
19.REMOVE FUEL TANK SUB-ASSEMBLY
Place a transmission jack under the fuel tank sub-assembly.
Remove the 2 bolts, 2 clips, 2 pins and 2 fuel tank bands.
Slowly lower the transmission jack slightly.
77651A
20.REMOVE FUEL TANK CUSHION
| *1 | No. 1 Fuel Tank Cushion |
| *2 | No. 2 Fuel Tank Cushion |
| *3 | No. 3 Fuel Tank Cushion |
Remove the No. 1, No. 2 and No. 3 fuel tank cushions from the fuel tank sub-assembly.
77207A
21.REMOVE FUEL RETURN TUBE SUB-ASSEMBLY AND FUEL TANK MAIN TUBE SUB-ASSEMBLY (for Single Tank Type)
| *1 | Fuel Tube |
| *2 | Fuel Tube Joint |
| *3 | Fuel Tube Joint Clip |
| *4 | O-Ring |
Remove the 2 fuel tube joint clips and pull out the fuel return tube sub-assembly and fuel tank main tube sub-assembly.
Remove any dirt and foreign matter on the fuel tube joint before performing this work.
Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.
Perform this work by hand. Do not use any tools.
Do not forcibly bend, twist or turn the nylon tube.
Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tubes.
Remove the fuel return tube sub-assembly and fuel tank main tube sub-assembly from the fuel tank sub-assembly.
77208A
22.REMOVE NO. 4 FUEL MAIN TUBE SUB-ASSEMBLY AND FUEL SUCTION TUBE SUB-ASSEMBLY (for Double Tank Type)
| *1 | Fuel Tube |
| *2 | Fuel Tube Joint |
| *3 | Fuel Tube Joint Clip |
| *4 | O-Ring |
Remove the 2 fuel tube joint clips and pull out the No. 4 fuel main tube sub-assembly and fuel suction tube sub-assembly.
Remove any dirt and foreign matter on the fuel tube joint before performing this work.
Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.
Perform this work by hand. Do not use any tools.
Do not forcibly bend, twist or turn the nylon tube.
Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tubes.
Detach the clamp and remove the No. 4 fuel main tube from the fuel tank sub-assembly.
Detach the clamp and remove the fuel suction tube sub-assembly from the fuel tank sub-assembly.
77209D
23.REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY, FUEL RETURN TUBE SUB-ASSEMBLY AND NO. 2 FUEL MAIN TUBE SUB-ASSEMBLY (for Double Tank Type)
| *1 | Fuel Tube |
| *2 | Fuel Tube Joint |
| *3 | Fuel Tube Joint Clip |
| *4 | O-Ring |
Remove the 3 fuel tube joint clips and pull out the fuel tank main tube sub-assembly, fuel return tube sub-assembly and No. 2 fuel main tube sub-assembly.
Remove any dirt and foreign matter on the fuel tube joint before performing this work.
Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.
Perform this work by hand. Do not use any tools.
Do not forcibly bend, twist or turn the nylon tube.
Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tubes.
Detach the clamp and remove the No. 2 fuel main tube sub-assembly from the fuel tank sub-assembly.
Detach the clamp and remove the fuel return tube sub-assembly from the fuel tank sub-assembly.
Remove the fuel tank main tube sub-assembly from the fuel tank sub-assembly.
77010
24.REMOVE FUEL TANK VENT TUBE ASSEMBLY (for Single Tank Type)
Protect the connector and tube joint of the fuel tank vent tube assembly with vinyl tape to prevent foreign matter from entering. Then clean off any mud or other foreign matter before proceeding with work.
| *a | Co-rotation Prevention Check Mark |
Apply a co-rotation prevention check mark to the fuel tank vent tube assembly and fuel tank sub-assembly.
The fuel tank sub-assembly cutout is attached to the protrusion on the fuel tank vent tube assembly.
If the fuel tank vent tube assembly and fuel tank sub-assembly are not firmly attached and the fuel pump gauge retainer is rotated, the fuel tank vent tube assembly will co-rotate and result in the fuel tank vent tube assembly and fuel tank sub-assembly being damaged.
Make sure to apply a co-rotation prevention check mark to prevent the fuel tank vent tube assembly from co-rotating.
| *1 | Fuel Pump Gauge Retainer |
| *a | SST (claw set) |
| *b | Rib |
| *c | Cutout |
| *d | SST (Claw Set) Incorrect Installation Point (Rotational Start Point Mark of Fuel Pump Gauge Retainer) |
Set 4 SSTs (claw sets) to the fuel pump gauge retainer and temporarily install.
Align the cutout of SST (claw set) to the rib of the fuel pump gauge retainer.
Do not place SST on the rotational start point mark of the fuel pump gauge retainer, otherwise SST (claw set) cannot be set correctly.
| *1 | Fuel Pump Gauge Retainer |
| *a | SST (Claw Set) |
| *b | Hook |
|
Press |
|
SST (Bolt) |
While firmly pressing the claw of SST into rib of the fuel pump gauge retainer, tighten the bolt.
| *a | SST (Plate) |
| *b | SST (Claw Set) |
|
SST (Bolt) |
Temporarily install SST (plate) to SST (claw set) with 4 SSTs (bolts).
| *a | Center of Fuel Pump Gauge Retainer |
| *b | SST (Plate) |
Adjust the position of SST (plate) so that the setting hole of SST (handle) aligns with the center of the fuel pump gauge retainer.
| *1 | Fuel Pump Gauge Retainer |
| *a | SST (Plate) |
| *b | SST (Claw Set) |
| *c | SST (Bolt) |
| *d | Rib |
|
Press |
While firmly pressing the SST (claw set) into rib of the fuel pump gauge retainer, tighten SST (bolt).
Install SST (handle) to SST (plate).
| *a | SST (Plate) |
| *b | SST (Handle) |
|
Loosen |
Slowly loosen the fuel pump gauge retainer by approximately 90°.
Do not use any tools other than SST, such as a screwdriver, etc.
Do not use excessive force when pressing down on SST, as the fuel tank vent tube assembly will place excessive force on the pump gauge retainer and be difficult to remove, and parts may be damaged.
Do not use an impact wrench or turn the SST handle with excessive force, as parts may be damaged.
While one person slowly loosens the fuel pump gauge retainer, have another person press down the rising fuel tank vent tube assembly, securely attach the protrusion of the fuel tank vent tube assembly to the groove of the fuel tank sub-assembly, and then remove the fuel pump gauge retainer while making sure that the fuel tank vent tube assembly is properly aligned.
| *a | SST (Plate) | *b | SST (Handle) |
| *c | Person in Charge of Loosening | *d | Person in Charge of Supporting |
| *e | Co-rotation Prevention Check Mark | - | - |
The fuel tank vent tube assembly is equipped with a spring that pushes against the bottom of the fuel tank sub-assembly to constantly lift the fuel tank vent tube assembly upwards.
If the fuel tank vent tube assembly and fuel tank sub-assembly are not firmly attached and the fuel pump gauge retainer is rotated, the fuel tank vent tube assembly will co-rotate and result in the fuel tank vent tube assembly and fuel tank sub-assembly being damaged.
Do not rotate the fuel pump gauge retainer when the co-rotation prevention check mark is out of place.
Do not bend the arm of the fuel sender gauge assembly.
Remove the gasket from the fuel tank sub-assembly.
77020A
25.REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY (for Double Tank Type)
77643A
26.REMOVE NO. 3 FUEL TANK PROTECTOR
Remove the 2 bolts.
Detach the 4 clamps and remove the No. 3 fuel tank protector.
77213B
27.REMOVE FUEL TANK TO FILLER PIPE HOSE
Loosen the clamp and remove the fuel tank to filler pipe hose from the fuel tank sub-assembly.