Home › Engine / Hybrid System › 1GD-FTV (FUEL) › FUEL TANK (for 3 Door) › from 2020.08
RM27T0E _51 Engine / Hybrid System _053670 1GD-FTV FUEL _0260581 FUEL TANK(for 3 Door) A

1GD-FTV FUEL  FUEL TANK(for 3 Door)  INSTALLATION  


PROCEDURE

Hide 77651A 1.INSTALL NO. 1 FUEL TANK CUSHION

a.

Install 2 new No. 1 fuel tank cushions to the fuel tank sub-assembly.


Hide 77295C 2.INSTALL FUEL TUBE GROMMET

a.

Attach the clamp to install the fuel tube grommet.


Hide 77011 3.INSTALL FUEL TANK FILLER PIPE LOWER SUB-ASSEMBLY

a.

Install a new gasket and the fuel tank filler pipe lower sub-assembly with the 8 screws.

Torque:
3.0 N*m (31 kgf*cm, 27 in.*lbf)


Hide 77269A 4.INSTALL FUEL TANK BREATHER HOSE

a.

Install the fuel tank breather hose to the fuel tank sub-assembly, and tighten the clamp to secure the hose.


Hide 77213B 5.INSTALL FUEL TANK TO FILLER PIPE HOSE

a.

Install the fuel tank to filler pipe hose to the fuel tank sub-assembly, and tighten the clamp to secure the hose.


Hide 83320 6.INSTALL FUEL SENDER GAUGE ASSEMBLY

a.

Install a new gasket and the fuel sender gauge assembly with the 5 screws.

Torque:
1.5 N*m (15 kgf*cm, 13 in.*lbf)

NOTICE:

Be careful not to bend the arm of the fuel sender gauge assembly.



Hide 77380 7.INSTALL FUEL CUT OFF VALVE ASSEMBLY

a.

Install the fuel cut off valve assembly to the fuel tank sub-assembly.


Hide 77026B 8.INSTALL NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY

a.

Install a new gasket and the No. 1 fuel evaporation tube sub-assembly with the 4 screws.

Torque:
1.5 N*m (15 kgf*cm, 13 in.*lbf)


Hide 77017D 9.INSTALL FUEL TANK VENT TUBE SUB-ASSEMBLY

a.

Install a new gasket and the fuel tank vent tube sub-assembly with the 7 screws and attach the 2 clamps.

Torque:
3.5 N*m (36 kgf*cm, 31 in.*lbf)


Hide 77701T 10.INSTALL FUEL TANK CHECK VALVE

a.

Connect the hose and install the fuel tank check valve.


Hide 77298C 11.INSTALL NO. 4 FUEL TUBE CLAMP

a.

Install the No. 4 fuel tube clamp to the fuel tank check valve and attach the clamp.


Hide 77100U 12.INSTALL FUEL TANK SUB-ASSEMBLY

a.

Set the fuel tank sub-assembly on a transmission jack and lift up the transmission jack.


b.

Install the 2 fuel tank bands with the 2 pins and 2 clips.


c.

Connect the 2 fuel tank bands with the 2 bolts.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 77269A 13.CONNECT FUEL TANK BREATHER HOSE

a.

Connect the fuel tank breather hose to the filler pipe, and tighten the clamp to secure the hose.


Hide 77213B 14.CONNECT FUEL TANK TO FILLER PIPE HOSE

a.

Connect the fuel tank to filler pipe hose to the filler pipe, and tighten the clamp to secure the hose.


Hide 15.CONNECT FUEL HOSE

a.

Connect the 2 fuel hoses to the fuel tank vent tube sub-assembly, and slide the 2 clamps to secure the hoses.


Hide 77606 16.INSTALL NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY

a.

Install the No. 1 fuel tank protector sub-assembly with the 5 bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 58325E 17.INSTALL REAR FLOOR SERVICE HOLE COVER

a.

Connect the fuel sender gauge connector and fuel tank ground connector.


b.

Install the rear floor service hole cover with the 3 screws.


Hide 19.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 20. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART