Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › from 2020.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0261011 BLIND SPOT MONITOR SYSTEM D

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  OPERATION CHECK  


BLIND SPOT MONITOR BEAM AXIS CONFIRMATION


HINT:

The blind spot monitor beam axis confirmation is performed to confirm whether the sensor's beam axis is correct, and perform adjustment of the beam axis by using reflector.


a.

When performing the blind spot monitor beam axis confirmation, move the vehicle to a place where the space shown in the illustration can be secured.

NOTICE:
·

Perform this inspection on level ground.

·

Make sure that there are no metal objects around the vehicle or on the ground.

·

Unload the vehicle before beginning the inspection.

·

Confirm that the tire pressure is correct before beginning the inspection.

·

Do not place any objects other than the reflector (such as a large metallic object) in or allow people to enter the inspection area (W 6 m [19.68 ft.] x L 6 m [19.68 ft.] x H 3 m [9.84 ft.]) shown in the illustration.



E305141C15
0.927,0.354 1.24,0.51 0.313,0.156 12 false *A 3.854,0.375 4.167,0.531 0.313,0.156 12 false *B 2.688,0.51 3,0.667 0.313,0.156 10 false *a 3.042,1.885 3.354,2.042 0.313,0.156 10 false *b 1.365,4.406 1.677,4.563 0.313,0.156 10 false *c 4.292,0.5 4.604,0.656 0.313,0.156 10 false *a 4.021,1.885 4.333,2.042 0.313,0.156 10 false *b 0.802,1.74 1.115,1.896 0.313,0.156 10 false a 6.24,1.719 6.573,1.885 0.333,0.167 10 false a 6.26,2.521 6.573,2.688 0.313,0.167 10 false b 0.719,2.521 1.031,2.688 0.313,0.167 10 false b 1.865,3.604 2.177,3.76 0.313,0.156 10 false c 5.052,3.563 5.365,3.719 0.313,0.156 10 false c
*A Left Side Of Vehicle *B Right Side Of Vehicle
*a Vehicle Center Line *b Edge of Rear Bumper
*c Inspection Area - -


Standard:
Location Measurement
a 1 m (3.28 ft.)
b 5 m (16.41 ft.)
c 6 m (19.68 ft.)



b.

Place the reflector.

i.

w/o Tire Carrier:

Hang a weight with a pointed tip from the center of the symbol emblem, and mark the front center point of the vehicle (point A) on the ground.

E407539C01
2.906,2.344 3.365,2.208 false 2.896,2.458 3.375,2.552 false 4.948,1.052 5.542,0.833 true 4.948,2.271 5.49,2.458 false 5.604,2.385 5.917,2.583 0.313,0.198 10 false *a 5.083,2.01 5.396,2.208 0.313,0.198 10 false *d 4.677,2.021 4.99,2.219 0.313,0.198 10 false *d 5.604,0.74 5.917,0.938 0.313,0.198 10 false *c 3.427,2.094 3.74,2.292 0.313,0.198 10 false *b 3.448,2.479 3.76,2.677 0.313,0.198 10 false A
*a String *b Weight
*c Center *d Bilateral Symmetry


HINT:

Lightly flick the string with your fingers several times to confirm that the string is perpendicular to the ground.



ii.

w/ Tire Carrier:

Hang a weight with a pointed tip from the center of the rear bumper cover, and mark the front center point of the vehicle (point A) on the ground.

E407540C01
2.927,2.458 3.333,2.573 true 2.927,2.302 3.292,2.271 true 5.469,1.917 5.792,2.115 true 3.396,2.542 3.708,2.74 0.313,0.198 10 false A 3.344,2.188 3.656,2.385 0.313,0.198 10 false *b 5.021,1.781 5.333,1.979 0.313,0.198 10 false *c 5.823,1.792 6.135,1.99 0.313,0.198 10 false *c 5.885,2.063 6.198,2.26 0.313,0.198 10 false *a
*a String *b Weight
*c Bilateral Symmetry - -


HINT:

Lightly flick the string with your fingers several times to confirm that the string is perpendicular to the ground.



iii.

Hang a weight with a pointed tip from the center of the radiator grille emblem, and mark the front center point of the vehicle (point B) on the ground.

E407541C01
2.031,1.01 2.656,0.833 true 2.021,2.167 2.448,2.323 false 3.615,2.156 4.042,2.313 false 3.635,2.583 4.042,2.458 false 2.719,0.74 3.031,0.938 0.313,0.198 10 false *c 2.146,1.927 2.458,2.125 0.313,0.198 10 false *d 1.729,1.927 2.042,2.125 0.313,0.198 10 false *d 2.531,2.271 2.844,2.469 0.313,0.198 10 false *a 3.448,2.063 3.76,2.26 0.313,0.198 10 false *b 3.49,2.531 3.802,2.729 0.313,0.198 10 false B
*a String *b Weight
*c Center *d Bilateral Symmetry


HINT:

Lightly flick the string with your fingers several times to confirm that the string is perpendicular to the ground.



iv.
E238824C16
0.635,1.26 1.094,0.448 false 1.094,0.448 1.292,0.448 false 1.281,1.302 1.438,1.458 0.156,0.156 10 false A 3.052,1.323 3.208,1.479 0.156,0.156 10 false B 1.344,0.385 1.656,0.583 0.313,0.198 10 false *a
*a Vehicle center line


Draw a vehicle center line so that it passes through mark A and B (front and rear center points).


v.

Enlarge and print out the poster shown in the illustration.

E444637C01
6.25,3.854 6.083,3.854 6.083,3.854 6.083,4.438 false 3.25,8.167 3.083,8.167 3.083,8.167 2.938,8.521 false 3.177,1.021 3.01,1.021 3.01,1.021 2.896,0.563 false 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.292,3.771 1.604,3.969 0.313,0.198 10 false *b 2.542,3.865 2.854,4.063 0.313,0.198 10 false a 2.594,4.771 2.906,4.969 0.313,0.198 10 false a 1.865,4.458 2.177,4.656 0.313,0.198 12 false A 3.302,0.938 3.615,1.135 0.313,0.198 10 false *c 3.313,8.083 3.625,8.281 0.313,0.198 10 false *c 6.302,3.781 6.615,3.979 0.313,0.198 10 false *d
*a Poster *b Edge Of Rear Bumper
*c Line C *d Vehicle center line


Standard:
Part Angle
a 77.8°



vi.
E334361C16
0.844,1.531 1.115,1.531 1.115,1.531 1.813,1.938 true 1.833,2.906 2.385,2.896 false 2.833,2.49 2.438,2.49 2.438,2.49 1.969,2.156 true 0.729,1.469 0.885,1.667 0.156,0.198 10 false A 2.427,2.854 2.74,3.052 0.313,0.198 10 false *b 2.875,2.438 3.188,2.635 0.313,0.198 10 false *a
*a Poster
*b Vehicle Center Line


Attach the printed poster to the floor with the vehicle center line aligned with point A as shown in the illustration.


vii.
E334362C16
2.073,3.771 1.865,3.771 1.865,3.771 1.813,3.375 false 2.781,3.292 2.479,3.292 2.479,3.292 2.344,3.542 false 2.813,2.438 2.344,2.448 2.344,2.448 1.729,3.167 true 0.583,3.74 0.74,3.938 0.156,0.198 10 false D 2.771,3.719 2.927,3.917 0.156,0.198 10 false D 0.271,0.302 0.583,0.479 0.313,0.177 10 false *a 1.625,4.396 1.938,4.573 0.313,0.177 10 false *b 2.146,3.719 2.458,3.896 0.313,0.177 10 false *d 2.833,3.219 3.146,3.396 0.313,0.177 10 false *c 2.885,2.365 3.042,2.563 0.156,0.198 10 false A
*a Vehicle Front
*b Vehicle Center Line
*c String
*d Poster


Align a piece of string with line C and mark point D at a distance of 3753 mm (12.31 ft.) from point A.


viii.

Set the reflector at the point D shown in the illustration below.

SST
09870-60000  (09870-60010)
09870-60040  

E334360C19
1.229,2.927 0.969,2.5 0.969,2.5 0.646,2.5 true 5.948,2.896 6.281,2.531 6.281,2.531 6.604,2.531 true 2.406,2.24 2.75,2.479 false 4.365,2.438 4.74,2.26 false 1.521,0.615 1.854,0.854 0.333,0.24 12 false *A 3.958,0.604 4.271,0.917 0.313,0.313 12 false *B 2.323,3.281 2.635,3.438 0.313,0.156 10 false *a 0.458,2.438 0.771,2.594 0.313,0.156 10 false *b 4.656,3.24 4.969,3.396 0.313,0.156 10 false *a 1.625,2.427 2.063,2.615 0.438,0.188 10 false a 5.385,2.385 5.823,2.573 0.438,0.188 10 false a 1.01,3 1.354,3.188 0.344,0.188 10 false D 6.083,3.021 6.427,3.208 0.344,0.188 10 false D 6.656,2.458 6.969,2.615 0.313,0.156 10 false *b 2.792,2.49 2.948,2.688 0.156,0.198 10 false A 4.25,2.448 4.406,2.646 0.156,0.198 10 false A
*A Left Side Of Vehicle *B Right Side Of Vehicle
*a Vehicle Center Line *b Reflector


Standard:
Part Length
a 3753 mm (12.31 ft.)


NOTICE:
·
E238830C07
1.469,0.667 1.979,0.667 1.979,0.667 1.625,1.177 false 2.031,0.594 2.344,0.792 0.313,0.198 10 false *a 0.604,1.563 0.917,1.76 0.313,0.198 10 false *b
*a SST (reflector)
*b 870 mm (2.85 ft.)


Set the reflector so that its center is 870 mm (2.85 ft.) above the ground.

·
B569107C04
2.625,1.563 2.417,1.563 2.417,1.563 2.167,0.948 true 3.031,3.677 2.823,3.677 2.823,3.677 2.635,4.198 true 2.677,1.49 2.99,1.688 0.313,0.198 10 false *a 3.083,3.594 3.396,3.792 0.313,0.198 10 false *b
*a Center Of Triangular Pyramid
*b SST (reflector)


The center of triangular pyramid is the reference point for the setting position and angle.

·

Set the reflector as shown in the illustration so that its center of triangular pyramid faces the blind spot monitor sensor.

·

Perform the operation as precisely as possible.





c.

Perform the blind spot monitor beam axis display.

i.

Connect the GTS to the DLC3.


ii.

Turn the engine switch on (IG).


iii.

Turn the blind spot monitor system on.


iv.

Turn the GTS on.


v.

Enter the following menus: Body Electrical / Blind spot monitor Master or Blind spot monitor Slave / Utility / BSM Master beam axis display or BSM Slave beam axis display.


vi.

Check the results displayed for the BSM beam axis display.

Allowable Range:
Item Blind Spot Monitor Sensor LH (Master) Blind Spot Monitor Sensor RH (Slave)
Angle -3.6 to +3.6° -3.6 to +3.6°


HINT:

If the displayed results are outside the permissible range, the following are possible causes. Therefore, implement countermeasures, check the blind spot monitor beam axis and perform the procedure again.

Possible Causes Countermeasure
Incorrect SST (reflector) position Check the position of SST (reflector) and checking space and perform the procedure again
A metallic object is located in the vicinity of the checking space Check the position of SST (reflector) and checking space and perform the procedure again
The blind spot monitor sensor installation is abnormal Check the installation condition of the blind spot monitor sensor



vii.

Perform the blind spot monitor beam axis adjustment using the GTS. Enter the following menus: Body Electrical / Blind spot monitor Master or Blind spot monitor Slave / Utility / BSM Master beam axis adjustment or BSM Slave beam axis adjustment.

HINT:

When values on the axis display are in the allowable range, performing this adjustment compensates for any deviation from the normal value.





BLIND SPOT MONITOR INSTALLATION CONDITION INSPECTION


NOTICE:
·

Perform this inspection on level ground.

·

Unload the vehicle before beginning the inspection.

·

Confirm that the tire pressure is correct before beginning the inspection.



HINT:

The blind spot monitor sensor installation condition inspection is performed to confirm whether the sensor is perpendicular to the floor surface (+/-2.2°) by using a digital angle gauge, and that the sensor is 16 to 24° from the line parallel to the vehicle center line.


a.

b.

Place the digital angle gauge on a level (gradient within 1%) and perform zero-point adjustment as shown in the illustration.

E369196C04
0.958,1.063 1.125,1.063 1.125,1.063 1.708,1.396 true 0.958,1.781 1.125,1.781 1.125,1.781 1.708,1.531 true 5.792,0.458 5.625,0.458 5.625,0.458 5.292,1.042 true 4.719,0.479 4.885,0.479 4.885,0.479 5.135,1.063 true 1.958,2.417 2.135,2.625 0.177,0.208 10 false *c 5.073,2.167 5.313,2.375 0.24,0.208 10 false *d 0.698,0.979 1.156,1.177 0.458,0.198 10 false *a 0.719,1.698 1.177,1.896 0.458,0.198 10 false *b 4.552,0.396 5.01,0.594 0.458,0.198 10 false *b 5.906,0.365 6.365,0.563 0.458,0.198 10 false *a
*a (+) *b (-)
*c When Storing Zero Point *d After Storing Zero Point, Indicates 90° When Fully Horizontal



c.
E444638C01
1.146,3.219 1.229,3.219 1.229,3.219 1.615,2.708 true 1,1.281 1.083,1.281 1.083,1.281 1.854,1.906 true 2.031,1.396 2.427,0.583 2.427,0.583 2.51,0.583 true 0.781,1.188 0.99,1.417 0.208,0.229 10 true *a 0.948,3.125 1.156,3.354 0.208,0.229 10 true *b 2.531,0.49 2.74,0.719 0.208,0.229 10 true *c
*a Digital Angle Gauge
*b Blind Spot Monitor Sensor
*c Outward Facing Surface


Set the digital angle gauge to the outward facing surface of the blind spot monitor sensor as shown in the illustration, and check that the perpendicular angle of the blind spot monitor sensor is within the permissible range.

HINT:
E367769C05
2.49,1.229 2.74,0.979 2.74,0.979 2.823,0.979 true 1.333,0.75 1.583,0.25 1.583,0.25 1.667,0.25 true 0.719,1.833 0.802,1.833 0.802,1.833 0.927,1.542 true 2.26,0.75 2.646,0.948 0.385,0.198 10 false *a 2.25,1.583 2.635,1.781 0.385,0.198 10 false *b 2.896,0.917 3.281,1.115 0.385,0.198 10 false *c 1.75,0.198 2.833,0.396 1.083,0.198 10 false *d 0.521,1.76 1.188,2.01 0.667,0.25 10 false *e
*a (+)
*b (-)
*c Horizontal Line
*d Digital Angle Gauge
*e Outward Facing Surface


The outward facing surface (installation angle) is positive (+) when it faces higher than horizontal.


Standard:
Item Allowable Range
Blind Spot Monitor Sensor LH +87.8 to +92.2°
Blind Spot Monitor Sensor RH +87.8 to +92.2°



d.
E338854C05
0.698,2.073 1.073,2.396 true 2.135,3.125 2.51,3.448 true 0.479,2.75 0.917,2.74 true 1.813,3.458 2.115,3.688 true 0.083,0.094 0.396,0.25 0.313,0.156 12 false *A 1.104,2.948 1.417,3.104 0.313,0.156 10 false A 1.771,4.344 2.083,4.5 0.313,0.156 10 false *b 2.885,0.969 3.198,1.125 0.313,0.156 10 false *c 0.5,1.969 0.813,2.125 0.313,0.156 10 false *d 0.292,2.656 0.604,2.813 0.313,0.156 10 false *e 0.875,0.969 1.188,1.125 0.313,0.156 10 false *c 2.563,3.458 2.875,3.615 0.313,0.156 10 false *d 1.365,3.396 1.521,3.594 0.156,0.198 10 false y 1.667,0.167 1.979,0.365 0.313,0.198 10 false *a 2.146,3.708 2.458,3.865 0.313,0.156 10 false *e 1.927,2.083 2.094,2.281 0.167,0.198 10 true a
*A Vehicle Rear (LH)
*a Vehicle Front
*b Vehicle Rear
*c Line Parallel To The Vehicle Center Line
*d Stud Bolt
*e Stud Bolt Center Line


Using the sensor installation stud bolt center lines as a reference, check that the stud bolts are as shown in the illustration.

Standard:
Dimension Specified Value
a 108 mm (4.25 in.)
y 29 to 44 mm
(1.14 to 1.73 in.)

Degree Specified Value
A 16 to 24°


HINT:

If the results are not as specified, it is possible that the blind spot monitor sensor installation area (frame, stud bolt) is deformed, so make corrections as necessary.



e.

Install the rear bumper assembly.