Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2020.08
RM27T0E _58 Vehicle Interior _053733 METER / GAUGE / DISPLAY _0261082 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Tachometer Malfunction  


DESCRIPTION

In this circuit, the meter CPU receives engine speed signals from the ECM. The meter CPU displays the engine speed calculated based on the data received from the ECM.

WIRING DIAGRAM

E349711E03
1.375,2.635 1.833,2.833 0.458,0.198 10 false ECM 4.219,2.646 6.417,2.885 2.198,0.24 10 false Combination Meter Assembly 0.75,3.385 2.563,3.594 1.813,0.208 10 false : CAN Communication Line

PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication DTC is output.


ii.

w/o Central Gateway ECU (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM).

Result
Result Proceed to
CAN communication DTC is not output. A
CAN communication DTC is output. (w/ Central Gateway ECU) B
CAN communication DTC is output. (w/o Central Gateway ECU) C




A

2.PERFORM ACTIVE TEST USING GTS (TACHO METER OPERATION)

B

C

2.PERFORM ACTIVE TEST USING GTS (TACHO METER OPERATION)
a.

Using the GTS, perform the Active Test (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

Combination Meter
Tester Display Test Part Control Range Diagnostic Note
Tacho Meter Operation Tachometer OFF, 0, 1000, 2000, 3000, 4000, 5000, 6000 or 7000* (rpm) -

*: for 1GR-FE, 2TR-FE

OK:

Tachometer indication is normal.



Result
Result Proceed to
CAN communication DTC is not output. A
CAN communication DTC is output. (w/ Central Gateway ECU) B
CAN communication DTC is output. (w/o Central Gateway ECU) C



A

3.READ VALUE USING GTS (ENGINE RPM)

B

C

3.READ VALUE USING GTS (ENGINE RPM)
a.

Using the GTS, read the Data List (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Engine Rpm Engine speed/Min.: 0 rpm, Max.: 12750 rpm 600 to 700 rpm (When idling) If the data received from the ECM exceeds the range that can be displayed on the meter, the meter continues to display the maximum value of the range.

OK:

Engine speed displayed on the intelligent tester is almost the same as the tachometer indication.



b.

Record the engine speed displayed on the intelligent tester.

HINT:

Check the engine speed when the engine is fully warmed up and the air conditioning and all electrical accessories are off.




OK

REPLACE COMBINATION METER ASSEMBLY

NG

4.READ VALUE USING GTS (ENGINE SPEED)
4.READ VALUE USING GTS (ENGINE SPEED)
a.

Using the GTS, read the Data List (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

Engine and ECT (except 1GD-FTV)
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Engine Speed Vehicle speed/Min.: 0 rpm, Max.: 16383.75 rpm Actual engine speed -

Engine (for 1GD-FTV)
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Engine Speed Vehicle speed/Min.: 0 rpm, Max.: 16383.75 rpm
·

50 to 400 rpm: Cranking

·

610 to 750 rpm: Idling with warm engine


When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 or varies greatly from the actual engine speed.

OK:

Engine speed displayed on GTS is almost same as actual engine speed.


Result
Result Proceed to
OK A
NG (for Gasoline Engine) B
NG (for Diesel Engine) C

HINT:
·

for 1GR-FE:

If it is necessary to refer to the SFI system, refer to the following procedures (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

for 2TR-FE:

If it is necessary to refer to the SFI system, refer to the following procedures (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

for 1GD-FTV:

If it is necessary to refer to the ECD system, refer to the following procedures (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

for 1GD-FTV (w/ Urea SCR System):

If it is necessary to refer to the ECD system, refer to the following procedures (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

for 1GD-FTV (w/ DPF):

If it is necessary to refer to the ECD system, refer to the following procedures (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>HOW TO PROCEED WITH TROUBLESHOOTING)

·

for 5L-E:

If it is necessary to refer to the ECD system, refer to the following procedures (See page Engine / Hybrid System>5L-E (ENGINE CONTROL)>ECD SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).





A

5.CHECK ECM

B

C

5.CHECK ECM

b.

Check that the operation of the tachometer returns to normal.

OK:

The operation of the tachometer returns to normal.




OK

END (ECM IS DEFECTIVE)

NG

REPLACE COMBINATION METER ASSEMBLY