Use this procedure to troubleshoot the immobiliser system.
*: Use the GTS.
| Proceed to |
|---|
| NEXT |
NEXT
In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
The following 5 items are important points for problem analysis:
| What | Vehicle model, system name |
| When | Date, time, occurrence frequency |
| Where | Whether the problem occurs at a specific location. |
| Under what conditions? | Whether the doors were locked or unlocked, whether the engine switch was on, whether the engine was running. |
| How did it happen? | Problem symptoms |
| Proceed to |
|---|
| NEXT |
NEXT
Measure the battery voltage.
11 to 14 V
If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.
A simple method to determine whether the battery is discharged is to operate the horn.
| Proceed to |
|---|
| NEXT |
NEXT
When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
| Proceed to |
|---|
| NEXT |
NEXT
Using the GTS, check for CAN communication system DTCs.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM
| Result | Proceed to |
|---|---|
| CAN DTCs are not output | A |
| CAN DTCs are output | B |
A
B
Using the GTS, check for LIN communication system DTCs.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| LIN DTCs are not output | A |
| LIN DTCs are output | B |
A
B
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check for DTCs and make a note of any codes that are output.
Based on the DTCs output above, proceed to each diagnostic procedure.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| SFI system DTCs are output (1GR-FE) | B |
| SFI system DTCs are output (2TR-FE) | C |
| ECD system DTCs are output (1GD-FTV) | D |
| ECD system DTCs are output (1GD-FTV (w/ DPF)) | E |
| ECD system DTCs are output (1GD-FTV (w/ Urea SCR System)) | F |
| Steering lock system DTCs are output | G |
| Immobiliser system DTCs are output | H |
A
B
C
D
E
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DIAGNOSTIC TROUBLE CODE CHART
F
G
H
Refer to Problem Symptoms Table.
| Result | Proceed to |
|---|---|
| Fault is not listed in problem symptoms table | A |
| Fault is listed in problem symptoms table | B |
A
B
Data List / Active Test
| Proceed to |
|---|
| NEXT |
NEXT
If the certification ECU (smart key ECU assembly), ID code box (immobiliser code ECU), steering lock ECU (steering lock actuator or upper bracket assembly), main body ECU (multiplex network body ECU), ECM, or electrical key transmitter sub-assembly are replaced, refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
Before checking for DTCs, perform the "DTC Output Confirmation Operation" of each diagnostic procedure.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| Immobiliser system DTCs are output | B |
A
B